Please note that User Registration has been temporarily disabled due to a recent increase in automated registrations. If anyone needs an account, please request one here: RequestAccount. Thanks for your patience!--Wmat (talk)
Please email User:Wmat if you experience any issues with the Request Account form.

Difference between revisions of "Adafruit: 2-Axis Thumb Joystick"

From eLinux.org
Jump to: navigation, search
(BeagleBone Usage)
(BeagleBone Usage)
Line 18: Line 18:
  
 
[[File:BeagleBone_Adafruit_2axis_Joystick_mmoravec.jpg|300px]]
 
[[File:BeagleBone_Adafruit_2axis_Joystick_mmoravec.jpg|300px]]
 +
 +
  
 
The pinout is as shown:
 
The pinout is as shown:
  
 
[[File:Bone_P9_pinout.jpg|300px]]
 
[[File:Bone_P9_pinout.jpg|300px]]
 +
 +
  
 
Pins 36 and 38 I have wired to the 0-1.8V analog inputs. I have wired VCC to the Beagle's 1.8V analog VCC output(pin 32). The ground wire from the joystick is wired to the analog ground on the beagle(pin 34). The select GPIO signal I have routed to the GPIO_7 pin(pin 42).
 
Pins 36 and 38 I have wired to the 0-1.8V analog inputs. I have wired VCC to the Beagle's 1.8V analog VCC output(pin 32). The ground wire from the joystick is wired to the analog ground on the beagle(pin 34). The select GPIO signal I have routed to the GPIO_7 pin(pin 42).
  
 
Using this configuration one can take the analog inputs with the GPIO selector and do about anything that requires two axises of movement and a selection knob. Enjoy!
 
Using this configuration one can take the analog inputs with the GPIO selector and do about anything that requires two axises of movement and a selection knob. Enjoy!

Revision as of 06:04, 21 September 2012

2axisthumbstick MED.jpg

Overview

The Adafruit: 2-Axis Thumb Joystick uses 2 10 kOhm pots which are adjusted by moving the joystick. The joystick and development board can be purchased from the Adafruit Website. The joystick is simplistic enough that Adafruit does not provide a datasheet.

From the Manufactorer: This mini-kit makes it easy to mount a PSP/Xbox-like thumb joystick to your project. The thumbstick is an analog joystick - more accurate and sensitive than just 'directional' joysticks - with a 'press in to select' button. Since it's analog, you'll need to analog reading pins on your microcontroller to determine X and Y. Having an extra digital input will let you read the switch.

Inputs and Outputs

The Adafruit joystick takes a supply voltage (Vs) of up to 5V. The analog outputs have a direct correlation to the resistance observed by the analog joystick. At the resting position, the resistance in both axis is at its middle resistance or 5k. At either extreme of the range of motion, there is either enough resistance for the analog inputs to register a 0 or so little resistance that the supply line to the analog input looks open.

BeagleBone Usage

The BeagleBone can support up to 8 analog inputs and has the ability to supply an analog 1.8 V voltage and an analog ground. I have connected my beagle as shown after soldering the joystick and some wires to the dev board:

BeagleBone Adafruit 2axis Joystick mmoravec.jpg


The pinout is as shown:

Bone P9 pinout.jpg


Pins 36 and 38 I have wired to the 0-1.8V analog inputs. I have wired VCC to the Beagle's 1.8V analog VCC output(pin 32). The ground wire from the joystick is wired to the analog ground on the beagle(pin 34). The select GPIO signal I have routed to the GPIO_7 pin(pin 42).

Using this configuration one can take the analog inputs with the GPIO selector and do about anything that requires two axises of movement and a selection knob. Enjoy!