Adafruit: RTC DS1307

Revision as of 20:21, 10 December 2013 by Alvareap (Talk | contribs)

Jump to: navigation, search
Wiring for DS1307 RTC with Beaglebone Black.


Adafruit's DS1307 Real-Time Clock Breakout Kit uses a Maxim Integrated DS1307. The DS1307 can be used to store a the date and time. It may lose or gain 2 seconds a day.

Inputs and Outputs

The RTC must be powered from the BeagleBone's 5V supply (note it must be powered from the DC adapter, or else I2C bus will hang, as there is not enough current provided by the usb bus to power the RTC). The RTC uses an I2C interface to communicate with the BBB.

Bone Usage

On boot BBB is connected power from the DC power adapter, therefore it loads the correct /dev/rtc modules.

Pin mappings:

P9 pin # (BeagleBone pin) -> Panel pin (wire color)

1 (GND) -> GND

5 (VDD_5V) -> VCC

5 (VDD_5V) -> SQW (through 10k pullup resistor)

19 (I2C2_SCL) -> SCL

20 (I2C2_SCL) -> SDA

This code was adapted from Adafruit's sample code, and can be found at Alex Alvarez's github repository. sets up the RTC if it has never been set up before. If the BBB internal clock is lost, the script will copy the time over from the RTC. If the BBB is set up correctly the script will copy update the time from ntp servers, and write that time to the RTC module.

a=$(date +%Y)

if [[ $a < 2013 ]]; then
	echo ds1307 0x68 > /sys/class/i2c-adapter/i2c-1/new_device
	echo "Retrieving time from rtc"
	hwclock -s -f /dev/rtc1
	hwclock -w

	echo "Date has been read from RTC, and copied to system clock"
   # Assumes if date is correct on reboot, that you are connected to network
   echo "Fetching time from ntp server"
   $(/usr/bin/ntpdate -b -s u  

   if [ -e /dev/rtc1 ]; then
     echo "Writing system clock to RTC"
     hwclock -w -f /dev/rtc1
    echo ds1307 0x68 > /sys/class/i2c-adapter/i2c-1/new_device
     echo "Writing system clock to RTC"
     hwclock -w -f /dev/rtc1

# Sets time zone to Eastern (GMT -5)
$( ln -sf /usr/share/zoneinfo/America/New_York /etc/localtime )
echo "The new date is:" $(date)

This file manipulates the rtc-ds1307.service to run from a paramaterized directory. It copies over, and rtc-ds1307.service to the given directory, and manipulates the variables inside of the service file to react accordingly. It then enables the service, so that it will run at startup.

In order to manually start the service execute: systemctl start rtc-ds1306.service and stop: systemctl stop rtc-ds1306.service

# By Alex Alvarez,
# This script creates a new directory if passed as the parameter, and places the rtc script and service files in those given directories. It also manipulates the service file such that the working directories change with the given directory parameter.
# If no paramter is given the working directory is used as the service location

if [ "$1" ]; then

  $(mkdir $2)



SED_ARG="-e 's@WorkingDirectory=.*@WorkingDirectory=$DIR@' rtc-ds1307.service" 

eval sed "$SED_ARG" > tmp.txt

mv tmp.txt rtc-ds1307.service

cp rtc-ds1307.service $DIR
cp $DIR

systemctl enable $DIR/rtc-ds1306.service


Description=DS1307 RTC Service