Difference between revisions of "BeagleBoard/DSP Howto"
(Add kernel driver information.) |
(Add OpenMAX IL stuff.) |
||
| Line 24: | Line 24: | ||
modprobe bridgedriver base_img=baseimage.dof | modprobe bridgedriver base_img=baseimage.dof | ||
</code> | </code> | ||
| + | |||
| + | '''note''': baseimage.dof will be mentioned in later steps. | ||
| + | |||
| + | == TI binaries == | ||
| + | |||
| + | In order to get the DSP binaries for multimedia processing you need to download TI's OpenMAX IL [https://omapzoom.org/gf/download/frsrelease/111/396/tiopenmax-0.3.tar.gz package]. Once you have extracted the tarball you'll have to run the installer ''TI-OMX-Sample-Firmware-0.3-Linux-x86-Install'' and accept the license agreement. | ||
| + | |||
| + | You would end up with a bunch of binaries in <code>lib/dsp</code>, copy them to your root filesystem at the same location (/lib/dsp). | ||
| + | |||
| + | == OpenMAX IL == | ||
| + | |||
| + | The easiest way to use the DSP capabilities is through the [http://www.khronos.org/openmax/ OpenMAX IL] API, but in order to compile TI's implementation a special DSP library is required. | ||
| + | |||
| + | === libdspbridge === | ||
| + | |||
| + | git clone git://github.com/felipec/libdspbridge.git | ||
| + | cd libdspbridge | ||
| + | make DESTDIR='''rootfs''' install | ||
| + | |||
| + | === libomxil-ti === | ||
| + | |||
| + | git clone git://github.com/felipec/libomxil-ti.git | ||
| + | cd libomxil-ti | ||
| + | make BRIDGE_CFLAGS=-I../'''libdspbridge'''/inc BRIDGE_LIBS=-L../'''libdspbridge'''/lib DESTDIR='''rootfs''' install | ||
Revision as of 08:54, 22 September 2008
This article explains how to use the DSP with TI's deliverables.
Kernel driver
In order to use the DSP you would need TI's bridgedriver module on the kernel. For that you would need Hiroshi's patches on top of linux-omap:
git clone http://www.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
cd linux-omap-2.6
wget http://4869037.web.fc2.com/tidspbridge-20080920.tgz
tar xvzf tidspbridge-20080920.tgz
git am *.patch
make omap3_beagle_defconfig
Then make menuconfig and add the following options in the menuconfig:
CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE=14 CONFIG_MPU_BRIDGE=m
On the board use this to load the module:
modprobe bridgedriver base_img=baseimage.dof
note: baseimage.dof will be mentioned in later steps.
TI binaries
In order to get the DSP binaries for multimedia processing you need to download TI's OpenMAX IL package. Once you have extracted the tarball you'll have to run the installer TI-OMX-Sample-Firmware-0.3-Linux-x86-Install and accept the license agreement.
You would end up with a bunch of binaries in lib/dsp, copy them to your root filesystem at the same location (/lib/dsp).
OpenMAX IL
The easiest way to use the DSP capabilities is through the OpenMAX IL API, but in order to compile TI's implementation a special DSP library is required.
libdspbridge
git clone git://github.com/felipec/libdspbridge.git cd libdspbridge make DESTDIR=rootfs install
libomxil-ti
git clone git://github.com/felipec/libomxil-ti.git cd libomxil-ti make BRIDGE_CFLAGS=-I../libdspbridge/inc BRIDGE_LIBS=-L../libdspbridge/lib DESTDIR=rootfs install
