Revision as of 07:50, 30 October 2014

This page is about running a (ARM EABIhf) Debian distribution at BeagleBoard. BeagleBoard will boot the (ARM EABIhf) Debian distribution from SD card. Debian's NetInstall will be used to install Debian onto your Beagle.

Help

If you need any help:

Kernel related help:
- Email Beagleboard user group *Recommended method
- #beagle: Beagle irc on freenode, accessible also by web interface (logs)
- Kernel Tree's
  - v3.17.x kernel branch
  - Development Kernel source code

When asking for help, please provide some debugging information:
- U-Boot Version installed on board
- Kernel Version: uname -a
- pastebin dmesg
  - Copy from serial port or use "dmesg | pastebinit" (sudo apt-get install pastebinit)

Official BeagleBoard.org Images for shipping with BeagleBone Black

http://beagleboard.org/source

Recommended Beagle Software

Mainline U-Boot:

All old Ax, Bx, Cx and Dx boards are required to upgrade to at least these U-Boot versions.
XM Boards have no NAND, so MLO/u-boot.img is always required on the first partition
Directions: Upgrade X-loader and U-Boot

Debian NetInstall

Scripts:

git clone https://github.com/RobertCNelson/netinstall.git
cd netinstall

Device Options:

BeagleBoard --dtb omap3-beagle
BeagleBoard xM --dtb omap3-beagle-xm
BeagleBone (serial) --dtb am335x-bone-serial
BeagleBone (video via cape) --dtb am335x-bone-video
BeagleBone Black --dtb am335x-boneblack
PandaBoard (A1->A3) --dtb omap4-panda
PandaBoard (A4->Ax) --dtb omap4-panda-a4
PandaBoard ES  --dtb omap4-panda-es

You will need a 1GB SD card or greater.

Standard System : ~455MB
+ Desktop environment (GNOME) : ~2.9GB

Debian Wheezy

Quick Install script for "board"

sudo ./mk_mmc.sh --mmc /dev/sdX --dtb "board" --distro wheezy-armhf

So For the BeagleBoard xM:

sudo ./mk_mmc.sh --mmc /dev/sdX --dtb omap3-beagle-xm --distro wheezy-armhf

Options:
- --firmware : installs firmware
- --serial-mode : debian-installer uses Serial Port

Demo Image

Debian Stable (wheezy)

Default username/password:

username: debian
password: temppwd

Image Updated:

2014-10-29
- Beagle/Beagle xM: v3.17.1-armv7-x3 kernel
- BeagleBone/BeagleBone Black: v3.14.22-ti-r31 kernel
- OMAP5432 uEVM: v3.14.22-ti-r31 kernel
2014-08-13
- Beagle/Beagle xM: v3.16.0-armv7-x4 kernel
- BeagleBone/BeagleBone Black: v3.8.13-bone63 kernel
- OMAP5432 uEVM: v3.16.0-armv7-lpae-x2 kernel
2014-07-06
- repo now enabled (repos.rcn-ee.net/debian)
- Beagle/Beagle xM: v3.15.3-armv7-x4 kernel
- BeagleBone/BeagleBone Black: v3.8.13-bone59 kernel
- OMAP5432 uEVM: v3.15.3-armv7-lpae-x5 kernel

Services Active:

Note: Depending on your internal network these may work out of the box
Apache, Port 80: http://arm.local/ (Bone: via usb) http://192.168.7.2
SSH, Port 22: ssh debian@arm.local (Bone: via usb) debian@192.168.7.2
Getty, Serial Port

Default user: debian pass: temppwd

Get prebuilt image:

wget https://rcn-ee.net/deb/rootfs/wheezy/debian-7.7-console-armhf-2014-10-29.tar.xz

Verify Image with:

md5sum debian-7.7-console-armhf-2014-10-29.tar.xz
81f8a0ac3b44937cf0baefa82100ff27  debian-7.7-console-armhf-2014-10-29.tar.xz

Unpack Image:

tar xf debian-7.7-console-armhf-2014-10-29.tar.xz
cd debian-7.7-console-armhf-2014-10-29

Install Image:

Quick install script for [board]

sudo ./setup_sdcard.sh --mmc /dev/sdX --dtb board

board options:

BeagleBoard Ax/Bx/Cx/Dx - omap3-beagle
BeagleBoard xM - omap3-beagle-xm
BeagleBone/Black - beaglebone
OMAP5432 uEVM - omap5-uevm

So for the BeagleBoard xM:

sudo ./setup_sdcard.sh --mmc /dev/sdX --dtb omap3-beagle-xm

Advanced: Build Image:

Built with a fork of project-rootstock (ARM native mode, runs directly on BeagleBoard), using a script from omap-image-builder:

git clone https://github.com/RobertCNelson/omap-image-builder.git
cd omap-image-builder
git checkout v2014.10 -b tmp

Stable:

./RootStock-NG.sh -c rcn-ee_console_debian_stable_armhf

Testing:

./RootStock-NG.sh -c rcn-ee_console_debian_testing_armhf

Debian Testing (jessie)

Image Updated:

2014-10-29
- Beagle/Beagle xM: v3.17.1-armv7-x3 kernel
- BeagleBone/BeagleBone Black: v3.14.22-ti-r31 kernel
- OMAP5432 uEVM: v3.14.22-ti-r31 kernel
2014-08-13
- Beagle/Beagle xM: v3.16.0-armv7-x4 kernel
- BeagleBone/BeagleBone Black: v3.8.13-bone63 kernel
- OMAP5432 uEVM: v3.16.0-armv7-lpae-x2 kernel
2014-07-06
- repo now enabled (repos.rcn-ee.net/debian)
- Beagle/Beagle xM: v3.15.3-armv7-x4 kernel
- BeagleBone/BeagleBone Black: v3.8.13-bone59 kernel
- OMAP5432 uEVM: v3.15.3-armv7-lpae-x5 kernel

Get prebuilt image:

wget https://rcn-ee.net/deb/rootfs/jessie/debian-jessie-console-armhf-2014-10-29.tar.xz

Verify Image with:

md5sum debian-jessie-console-armhf-2014-10-29.tar.xz
d395f81a1044400ba07cec60e86d4262  debian-jessie-console-armhf-2014-10-29.tar.xz

Unpack image:

tar xf debian-jessie-console-armhf-2014-10-29.tar.xz
cd debian-jessie-console-armhf-2014-10-29

Then follow the directions shown above with the other images...

Flasher

eMMC: BeagleBone Black

This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager First press and hold the boot select button (next to the microSD card), then apply power (same procedure as the official CircuitCo images). The board should boot into Debian and begin flashing the eMMC, once completed all 4 LED's should be full ON. Simply remove power, remove the microSD card and Debian will now boot directly from eMMC.

Script for reference: (this is the script that writes to the eMMC)

https://github.com/RobertCNelson/boot-scripts/blob/master/tools/eMMC/init-eMMC-flasher-v3.sh

BTW: we are only writing about 500 megabytes to the eMMC, so the script will only take about 5-6 Minutes after power on.

Notes:

If only two LED's stay lit and nothing happens, the board has crashed due to lack of power. Retry with a 5Volt DC power supply connected.
If the 4 LED's blink a constant pattern, the eMMC write has failed. First REMOVE ALL capes, then retry again.
- (error -84: which may mean you've reached the max number of erase/write cycles...)

User: debian pass: temppwd

Image Updated:

2014-10-29
- BeagleBone Black: v3.14.22-ti-r31 kernel
2014-08-13
- BeagleBone Black: v3.8.13-bone63 kernel
2014-07-06
- repo now enabled (repos.rcn-ee.net/debian)
- BeagleBone Black: v3.8.13-bone59 kernel
- NOTE: You'll need to hold the BOOT button on powerup...

Get prebuilt image:

wget https://rcn-ee.net/deb/flasher/wheezy/BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Verify Image with:

md5sum BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
a704e493dd4b2b40e46cf63b41bd3ae5  BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Follow the "standard" update procedure.

http://elinux.org/Beagleboard:Updating_The_Software

Linux:

unxz BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
sudo dd if=./BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX

raw microSD img

BeagleBoard (classic)

This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager

User: debian pass: temppwd

Auto partition resize:

cd /opt/scripts/tools
git pull
./grow_partition.sh
sudo reboot

Image Updated:

2014-10-29
- Beagle: v3.17.1-armv7-x3 kernel
2014-08-13
- Beagle: v3.16.0-armv7-x4 kernel

Get prebuilt image:

wget https://rcn-ee.net/deb/microsd/wheezy/bb-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Verify Image with:

md5sum bb-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
750d02babacae353aae7ae143bd99441  bb-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Linux:

unxz bb-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
sudo dd if=./bb-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX

BeagleBoard xM

This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager

User: debian pass: temppwd

Auto partition resize:

cd /opt/scripts/tools
git pull
./grow_partition.sh
sudo reboot

Image Updated:

2014-10-29
- Beagle xM: v3.17.1-armv7-x3 kernel
2014-08-13
- Beagle xM: v3.16.0-armv7-x4 kernel
2014-07-06
- repo now enabled (repos.rcn-ee.net/debian)
- Beagle xM: v3.15.3-armv7-x4 kernel

Get prebuilt image:

wget https://rcn-ee.net/deb/microsd/wheezy/bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Verify Image with:

md5sum bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
0016b44de68b8a0cdce880dd48e3399e  bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Linux:

unxz bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
sudo dd if=./bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX

BeagleBone/BeagleBone Black

This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager

User: debian pass: temppwd

Auto partition resize:

cd /opt/scripts/tools
git pull
./grow_partition.sh
sudo reboot

Image Updated:

2014-10-29
- BeagleBone/BeagleBone Black: v3.14.22-ti-r31 kernel
2014-08-13
- BeagleBone/BeagleBone Black: v3.8.13-bone63 kernel
2014-07-06
- repo now enabled (repos.rcn-ee.net/debian)
- BeagleBone/BeagleBone Black: v3.8.13-bone59 kernel
- Black: NOTE: You'll need to hold the BOOT button on powerup...

Get prebuilt image:

wget https://rcn-ee.net/deb/microsd/wheezy/bone-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Verify Image with:

md5sum bone-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
b8079657951abc2350f67797a5aeddb9  bone-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Linux:

unxz bone-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
sudo dd if=./bone-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX

OMAP5432 uEVM

This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager

User: debian pass: temppwd

Auto partition resize:

cd /opt/scripts/tools
git pull
./grow_partition.sh
sudo reboot

Image Updated:

2014-10-29
- OMAP5432 uEVM: v3.14.22-ti-r31 kernel
2014-08-13
- OMAP5432 uEVM: v3.16.0-armv7-lpae-x2 kernel
2014-07-06
- repo now enabled (repos.rcn-ee.net/debian)
- OMAP5432 uEVM: v3.15.3-armv7-lpae-x5 kernel

Get prebuilt image:

wget https://rcn-ee.net/deb/microsd/wheezy/omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Verify Image with:

md5sum omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
3ae762eaae9fc712f19273d4ab61e509  omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz

Linux:

unxz omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
sudo dd if=./omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX

Debian Configuration

Serial Ports

To start a login console on ttyO2 (the serial header next to P9), edit /etc/inittab and add:

T0:23:respawn:/sbin/getty -L ttyO2 115200 vt102

To start a console on the USB ACM device, add the following to /etc/inittab,

GS0:23:respawn:/sbin/getty -L ttyGS0 115200 vt102

Install Latest Kernel Image

Script:

cd /opt/scripts/tools
git pull

Stable:

./update_kernel.sh

Testing:

./update_kernel.sh --beta-kernel

Custom: (has to be on rcn-ee.net)

./update_kernel.sh --kernel v3.8.13-bone59

Reboot with your new Kernel Image.

Xorg Drivers

Script:

cd /opt/scripts/tools/
git pull

BeagleBoard/PandaBoard:

cd /opt/scripts/tools/graphics/
./ti-omapdrm.sh

BeagleBone/BeagleBone Black:

cd /opt/scripts/tools/graphics/
./ti-tilcdc.sh

SGX Drivers

SGX BeagleBone/BeagleBone Black

Note, these are FBDEV only, no xorg/x11/etc...

Install sgx modules (3.14.x ti kernel):

sudo apt-get install ti-sgx-es8-modules-`uname -r`
sudo depmod -a `uname -r`
sudo update-initramfs -uk `uname -r`

Build SGX userspace (must be done on an x86, due to the TI 5.01.01.01 blob extractor)

git clone https://github.com/RobertCNelson/ti-linux-kernel-dev.git
cd ti-linux-kernel-dev/
git checkout origin/ti-linux-3.14.y -b tmp-sgx
./sgx_create_package.sh

Copy ./deploy/GFX_5.01.01.01.tar.gz to BeagleBone/BeagleBone Black and install

sudo tar xfv GFX_5.01.01.01.tar.gz -C /
cd /opt/gfxinstall/
sudo ./sgx-install.sh
sudo reboot

Verify omaplfb & pvrsrvkm loaded

debian@arm:~$ lsmod | grep omaplfb
omaplfb                12065  0 
pvrsrvkm              178782  1 omaplfb

SGX Demos

cd /opt/gfxsdkdemos/ogles2/
sudo ./OGLES2ChameleonMan

Building Kernel

Note, this section use to have a lot of details, but maintenance of the two wiki's became a pain, so for now on we will just link to my other pages:

Beagle/Beagle xM

http://eewiki.net/display/linuxonarm/BeagleBoard

BeagleBone

http://eewiki.net/display/linuxonarm/BeagleBone

BeagleBone Black

http://eewiki.net/display/linuxonarm/BeagleBone+Black

Panda/Panda ES

http://eewiki.net/display/linuxonarm/PandaBoard

Upgrading from Debian 5 to Debian 6

Upgrading from Debian 5 to Debian 6 report and tutorial.

Upgrading from Debian 6 (Squeeze) to Debian 7 (Wheezy)

Note, this only goes over "armel" -> "armel"... For users wishing to switch from "armel" -> "armhf" just re-install...

sudo apt-get update ; sudo apt-get upgrade
sudo sed -i -e "s/squeeze/wheezy/g" /etc/apt/sources.list
sudo apt-get update ; sudo apt-get install -y apt aptitude udev dpkg
sudo aptitude update ; sudo aptitude -y safe-upgrade ; sudo aptitude -y dist-upgrade

@@ Line 3: / Line 3: @@
 [[Category:Development Boards]]
 [[Category: BeagleBoard]]
-This page is about running a (ARM EABI) [http://www.debian.org/ Debian] distribution at [[BeagleBoard]]. BeagleBoard will boot the (ARM EABI) Debian distribution from [[BeagleBoard#MMC.2FSD_boot|SD card]]. To prepare the SD card and install (ARM EABI) Debian on it, [http://bellard.org/qemu/ QEMU] on host PC will be used, following Aurélien Jarno's excellent [http://www.aurel32.net/info/debian_arm_qemu.php Debian on an emulated ARM machine] howto.
+This page is about running a (ARM EABIhf) [https://www.debian.org/ Debian] distribution at [[BeagleBoard]]. BeagleBoard will boot the (ARM EABIhf) Debian distribution from [[BeagleBoard#MMC.2FSD_boot|SD card]]. Debian's NetInstall will be used to install Debian onto your Beagle.
-Note: Debian armel deb's are compiled for armv4t, this allows debian to support a larger number of arm devices with a single port, at only the sacrifice of speed.
-= KNOWN ISSUES =
-.6.29-oer* USB still flaky on the RevC ehci port.. --[[User:RobertCNelson|RobertCNelson]] 18:17, 6 May 2009 (UTC)
 = Help =
@@ Line 16: / Line 10: @@
 *Kernel related help:
+** [https://groups.google.com/group/beagleboard Email Beagleboard user group] *Recommended method
 ** ''#beagle'': Beagle irc on freenode, accessible also by [http://beagleboard.org/discuss web interface] ([http://www.beagleboard.org/irclogs/index.php logs])
-** [http://beagleboard.org/discuss Email beagleboard user groups]
+** Kernel Tree's
-** [https://launchpad.net/~beagleboard-kernel Launchpad Project "Beagleboard Kernel"]
+*** [https://github.com/RobertCNelson/armv7-multiplatform/ v3.17.x kernel branch]
-*** [https://code.launchpad.net/~beagleboard-kernel/+junk/2.6-stable Launchpad Stable Kernel 2.6.31 src]
+*** [https://github.com/RobertCNelson/linux-dev Development Kernel source code]
-*** [https://code.launchpad.net/~beagleboard-kernel/+junk/2.6-dev Launchpad Development Kernel 2.6.32 src]
-*** [https://code.launchpad.net/~beagleboard-kernel/+junk/2.6-mainline Launchpad Kernel git src]
-*** [https://code.launchpad.net/~beagleboard-kernel/+junk/omap-lucid Launchpad Kernel for Ubuntu Lucid (10.04)]
-** [http://rcn-ee.net/deb/ trac/svn interface for the kernel builds]
 *When asking for help, please provide some debugging information:
@@ Line 30: / Line 21: @@
 ** pastebin dmesg
 *** Copy from serial port or use "dmesg | pastebinit" (sudo apt-get install pastebinit)
+= Official BeagleBoard.org Images for shipping with BeagleBone Black =
+* http://beagleboard.org/source
 = Recommended Beagle Software =
-* Recent x-loader/MLO
-** RevC2/3 Boards are fine and do not need an upgrade
-** Old RevB Boards should upgrade there MLO from here: http://www.angstrom-distribution.org/beagleboard-demo-image-available
-* Recent U-Boot with 'boot.scr' scripts enabled
+Mainline U-Boot:
-** u-boot.bin from here: http://www.angstrom-distribution.org/beagleboard-demo-image-available
+* All old Ax, Bx, Cx and Dx boards are required to upgrade to at least these U-Boot versions.
-** Or this one I've archived: [http://elinux.org/BeagleBoardUbuntu#Upgrade_U-Boot U-Boot 2009.08+r37 Upgrade]
+* XM Boards have no NAND, so MLO/u-boot.img is always required on the first partition
-*** Version 2009.01 (factory installed on C2/3's) and earlier will not work with this guide
+* Directions: [http://elinux.org/BeagleBoardUbuntu#Upgrade_X-loader_and_U-boot Upgrade X-loader and U-Boot]
-= Native Install via debian-installer (NON QEMU based) =
+= Debian NetInstall =
-Note: This install method requires an LCD+usb(keyboard,etc), and uboot 2008-rc2 (Upgrading u-boot (2.6.27's and later)) or later..
-Testing First Release:
+Scripts:
+ git clone https://github.com/RobertCNelson/netinstall.git
+ cd netinstall
-==Development PC: Format SD Card==
+Device Options:
+ BeagleBoard --dtb omap3-beagle
+ BeagleBoard xM --dtb omap3-beagle-xm
+ BeagleBone (serial) --dtb am335x-bone-serial
+ BeagleBone (video via cape) --dtb am335x-bone-video
+ BeagleBone Black --dtb am335x-boneblack
+ PandaBoard (A1->A3) --dtb omap4-panda
+ PandaBoard (A4->Ax) --dtb omap4-panda-a4
+ PandaBoard ES  --dtb omap4-panda-es
 You will need a 1GB SD card or greater.
@@ Line 52: / Line 52: @@
   + Desktop environment (GNOME) : ~2.9GB
-Starting with an empty SD card and using gparted, create:
+== Debian Wheezy ==
-MiB Primary Partition, fat32
- Leave remaining space for the Debian-Installer
-==Development PC: Setup SD U-boot Partition==
+Quick Install script for "board"
+ sudo ./mk_mmc.sh --mmc /dev/sdX --dtb "board" --distro wheezy-armhf
-Mount your SD card fat32 partition. (/media/disk/)
+So For the BeagleBoard xM:
+ sudo ./mk_mmc.sh --mmc /dev/sdX --dtb omap3-beagle-xm --distro wheezy-armhf
-Debian Lenny Stable
+*Options:
- cd /media/disk/
+**--firmware : installs firmware
- sudo wget http://rcn-ee.net/deb/kernel/CC-beagle-v2.6.29-58cf2f1-oer44.1.uImage
+**--serial-mode : debian-installer uses Serial Port
- sudo wget http://ftp.debian.org/debian/dists/lenny/main/installer-armel/current/images/versatile/netboot/initrd.gz
- sudo mv CC-beagle-v2.6.29-58cf2f1-oer44.1.uImage uImage
- sudo gzip -d initrd.gz
- sudo dd if=initrd of=initrd.pad ibs=8388608 conv=sync
-Tested: 2.6.29-oer44.1 install RevB5 & RevC2 --[[User:RobertCNelson|RobertCNelson]] 18:53, 10 September 2009 (UTC)
+= Demo Image =
-==Beagleboard: Setup U-boot for netboot install==
+== Debian Stable (wheezy)  ==
-Mount SD card
+Default username/password:
- For Linux Kernel 2.6.29 and higher using DSS2
+*username: debian
- setenv bootcmd 'mmcinit; fatload mmc 0:1 0x80300000 uImage; fatload mmc 0:1 0x81600000 initrd.pad; bootm 0x80300000'
+*password: temppwd
- or
- setenv bootcmd 'mmc init; fatload mmc 0:1 0x80300000 uImage; fatload mmc 0:1 0x81600000 initrd.pad; bootm 0x80300000'
- Debian Install over DVI Port
- setenv bootargs 'console=tty0 ramdisk_size=8192 root=/dev/ram0 rw rootfstype=ext2 initrd=0x81600000,8M omapfb.mode=dvi:1280x720MR-16@60'
- Debian Install over the Serial Port *(this seems to be a regression from 2.6.28, which allowed you to specify both...)
- setenv bootargs 'console=ttyS2,115200n8 ramdisk_size=8192 root=/dev/ram0 rw rootfstype=ext2 initrd=0x81600000,8M'
- saveenv
- boot
-The debian-installer should load via the framebuffer, if the screen remains blank, try different resolutions for the bootargs:
+Image Updated:
+*2014-10-29
+** Beagle/Beagle xM: v3.17.1-armv7-x3 kernel
+** BeagleBone/BeagleBone Black: v3.14.22-ti-r31 kernel
+** OMAP5432 uEVM: v3.14.22-ti-r31 kernel
+*2014-08-13
+** Beagle/Beagle xM: v3.16.0-armv7-x4 kernel
+** BeagleBone/BeagleBone Black: v3.8.13-bone63 kernel
+** OMAP5432 uEVM: v3.16.0-armv7-lpae-x2 kernel
+*2014-07-06
+** repo now enabled (repos.rcn-ee.net/debian)
+** Beagle/Beagle xM: v3.15.3-armv7-x4 kernel
+** BeagleBone/BeagleBone Black: v3.8.13-bone59 kernel
+** OMAP5432 uEVM: v3.15.3-armv7-lpae-x5 kernel
-You shall adapt the resolution to you screen as following :
+Services Active:
-  omapfb.mode=dvi:1280x720MR-16@60
+  Note: Depending on your internal network these may work out of the box
-  Modes:
+  Apache, Port 80: http://arm.local/ (Bone: via usb) http://192.168.7.2
-  "1024x768MR-16@60""800x600MR-16@60" ...
+  SSH, Port 22: ssh debian@arm.local (Bone: via usb) debian@192.168.7.2
+ Getty, Serial Port
-Here is more explanation on dss video options : [http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=blob;f=Documentation/fb/modedb.txt;h=ec4dee75a35450376ad13442ea926eaf76de76aa;hb=HEAD]
+Default user: debian pass: temppwd
-  Choose a language
+Get prebuilt image:
-  C - No localization
+  wget https://rcn-ee.net/deb/rootfs/wheezy/debian-7.7-console-armhf-2014-10-29.tar.xz
-  English - English
- Configure the network:
+Verify Image with:
-  usb0: USB net <- See below for 2.6.29. Could not find usb0 with B7 installing 2.6.28.
+ md5sum debian-7.7-console-armhf-2014-10-29.tar.xz
-  eth0: Ethernet <- Your usb-ethernet device
+f8a0ac3b44937cf0baefa82100ff27  debian-7.7-console-armhf-2014-10-29.tar.xz
-  wlan0: Wifi <- Your usb-wifi device.. See [[BeagleBoardDebianWifiInstallInfo]] for my hack to set it up.
-  Configuring usb0 network bridge for 2.6.29:
+Unpack Image:
-  While you chose your keyboard layout, setup a bridge with ethX and usbX.
+  tar xf debian-7.7-console-armhf-2014-10-29.tar.xz
-   # ifconfig ethX 0.0.0.0
+ cd debian-7.7-console-armhf-2014-10-29
-   # ifconfig usbX 0.0.0.0
-   # brctl addbr brX
-   # brctl addif brX ethX
-   # brctl addif brX usbX
-   # ifconfig brX up
-   # dhclient brX
-  ''*Sometimes the first beagle DHCP will fail(probably due PC trying autoconnect), just run the auto configuration again and it will configure it right.''
- Continue the install without loading kernel modules? : <yes>
+Install Image:
-  Partition disks: This partitioner doesn't have the inform.....? : <yes>
+Quick install script for [board]
-  Logical Volume Manager not available: <Continue>
+  sudo ./setup_sdcard.sh --mmc /dev/sdX --dtb board
- Partition disks:
+board options:
-  Guided - Use the largest continuous free space
+*BeagleBoard Ax/Bx/Cx/Dx    - omap3-beagle
+*BeagleBoard xM             - omap3-beagle-xm
+*BeagleBone/Black           - beaglebone
+*OMAP5432 uEVM              - omap5-uevm
-  Partitioning scheme....
+So for the BeagleBoard xM:
+  sudo ./setup_sdcard.sh --mmc /dev/sdX --dtb omap3-beagle-xm
-Example:
+Advanced: Build Image:
- MMC/SD card #1 (mmcblk0) - 2.0 GB Unknown
- >  #1 primary  57.5 MB     fat32
- >  #2 primary   1.8 GB B f ext3  /
- >  #5 logical 148.0 MB   f swap  swap
- Finish partitioning and write changes to disk
-  Write the changes to disk? : <yes>
- No installable kernel was found in the defined APT sources? :
+Built with a fork of project-rootstock (ARM native mode, runs directly on BeagleBoard), using a script from omap-image-builder:
-  Continue without installing a kernel? : <yes>
-  Standard System
+  git clone https://github.com/RobertCNelson/omap-image-builder.git
+ cd omap-image-builder
+ git checkout v2014.10 -b tmp
- No BootLoader: <ok>
+Stable:
-==Beagleboard: Setup U-boot for Normal Boot==
+ ./RootStock-NG.sh -c rcn-ee_console_debian_stable_armhf
-Reboot (aka remove power)
-Uboot update bootcmd & bootargs
+Testing:
-  For Linux Kernel 2.6.29 and higher using DSS2
+  ./RootStock-NG.sh -c rcn-ee_console_debian_testing_armhf
- setenv bootcmd 'mmcinit; fatload mmc 0:1 0x80300000 uImage; bootm 0x80300000'
- or
- setenv bootcmd 'mmc init; fatload mmc 0:1 0x80300000 uImage; bootm 0x80300000'
- DVI Port
- setenv bootargs 'console=tty0 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro omapfb.mode=dvi:1280x720MR-16@60'
- Serial Port
- setenv bootargs 'console=ttyS2,115200n8 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro'
- saveenv
- boot
-Debian will fix the ext3 partition, it'll try to reboot, after halting remove and reapply power.
+== Debian Testing (jessie) ==
-==Beagleboard: install kernel-image==
+Image Updated:
+*2014-10-29
+** Beagle/Beagle xM: v3.17.1-armv7-x3 kernel
+** BeagleBone/BeagleBone Black: v3.14.22-ti-r31 kernel
+** OMAP5432 uEVM: v3.14.22-ti-r31 kernel
+*2014-08-13
+** Beagle/Beagle xM: v3.16.0-armv7-x4 kernel
+** BeagleBone/BeagleBone Black: v3.8.13-bone63 kernel
+** OMAP5432 uEVM: v3.16.0-armv7-lpae-x2 kernel
+*2014-07-06
+** repo now enabled (repos.rcn-ee.net/debian)
+** Beagle/Beagle xM: v3.15.3-armv7-x4 kernel
+** BeagleBone/BeagleBone Black: v3.8.13-bone59 kernel
+** OMAP5432 uEVM: v3.15.3-armv7-lpae-x5 kernel
-===Script File===
+Get prebuilt image:
-Note: this will be updated from time to time. (tested off course, may need "sudo apt-get install wget")
+ wget https://rcn-ee.net/deb/rootfs/jessie/debian-jessie-console-armhf-2014-10-29.tar.xz
-  wget http://www.rcn-ee.net/deb/kernel/update_kernel.sh
+Verify Image with:
-  sudo /bin/bash update-kernel.sh
+  md5sum debian-jessie-console-armhf-2014-10-29.tar.xz
+  d395f81a1044400ba07cec60e86d4262  debian-jessie-console-armhf-2014-10-29.tar.xz
-Note: vmlinuz symbolic link (yes <or> no)... Still not sure this matters, i select <yes>...
+Unpack image:
+ tar xf debian-jessie-console-armhf-2014-10-29.tar.xz
+ cd debian-jessie-console-armhf-2014-10-29
-===Manual Method===
+Then follow the directions shown above with the other images...
- cd /home/<user>
+= Flasher =
- sudo apt-get install uboot-mkimage
- wget http://rcn-ee.net/deb/kernel/beagle/lenny/v2.6.29-58cf2f1-oer44.1/linux-image-2.6.29-oer44.1_1.0lenny_armel.deb
- sudo dpkg -i linux-image*
-Extract linux-image's vmlinuz-*
+== eMMC: BeagleBone Black ==
- dpkg -x linux-image* ./temp
-Mount fat32 partition
+This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager  First press and hold the boot select button (next to the microSD card), then apply power (same procedure as the official CircuitCo images). The board should boot into Debian and begin flashing the eMMC, once completed all 4 LED's should be full ON.  Simply remove power, remove the microSD card and Debian will now boot directly from eMMC.
- sudo mount /dev/mmcblk0p1 /mnt
-Build uboot compatible image and copy to fat32 boot partition
+Script for reference: (this is the script that writes to the eMMC)
-  sudo mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 -n "Linux" -d ./temp/boot/vmlinuz-*  /mnt/uImage
+  https://github.com/RobertCNelson/boot-scripts/blob/master/tools/eMMC/init-eMMC-flasher-v3.sh
-Clean up
+BTW: we are only writing about 500 megabytes to the eMMC, so the script will only take about 5-6 Minutes after power on.
- rm -rfd temp
-Sync, umount Partitions and Reboot
+Notes:
+* If only two LED's stay lit and nothing happens, the board has crashed due to lack of power. Retry with a 5Volt DC power supply connected.
+* If the 4 LED's blink a constant pattern, the eMMC write has failed. First REMOVE ALL capes, then retry again.
+** (error -84: which may mean you've reached the max number of erase/write cycles...)
-= QEMU install method via debian-installer (emulated arm core via Desktop PC)=
+User: debian
+pass: temppwd
-This methods lasted 4 hours on a PC Ubuntu/Lenny (P4 2GHz) with an external USB2.0 card reader.
+Image Updated:
-Install QEMU on your host PC. This assumes that your host PC is running Debian as well. If not, install QEMU the way your host PC distribution uses.
+*2014-10-29
- apt-get install qemu
+** BeagleBone Black: v3.14.22-ti-r31 kernel
-Note: If your debian armel image crashes while fscking the partition, rebuild qemu from trunk.
+*2014-08-13
+** BeagleBone Black: v3.8.13-bone63 kernel
+*2014-07-06
+** repo now enabled (repos.rcn-ee.net/debian)
+** BeagleBone Black: v3.8.13-bone59 kernel
+** NOTE: You'll need to hold the BOOT button on powerup...
-==Development PC: Format SD Card==
+Get prebuilt image:
+ wget https://rcn-ee.net/deb/flasher/wheezy/BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-You will need a 1GB SD card or greater, depending on the installation chosen :
+Verify Image with:
-  Standard System (without graphical environment) : ~455MB
+  md5sum BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-  + Desktop environment (GNOME) : ~2.3GB
+  a704e493dd4b2b40e46cf63b41bd3ae5  BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-Please note that installer download all packages before installing them, that's why you'll need more space disk.
-Starting with an empty SD card and using gparted/fdisk, create:
+Follow the "standard" update procedure.
-MiB Primary Partition, fat32
+ http://elinux.org/Beagleboard:Updating_The_Software
- Leave remaining space for the Debian-Installer
-==Development PC: Preparation==
+Linux:
+ unxz BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
+ sudo dd if=./BBB-eMMC-flasher-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX
-Create a working directory to keep your files organized.
+= raw microSD img =
- mkdir debian-armel
+== BeagleBoard (classic) ==
- cd debian-armel/
- wget ftp://ftp.us.debian.org/debian/dists/lenny/main/installer-armel/current/images/versatile/netboot/initrd.gz
- wget ftp://ftp.us.debian.org/debian/dists/lenny/main/installer-armel/current/images/versatile/netboot/vmlinuz-2.6.26-2-versatile
-==Development PC: Install Debian in QEMU==
+This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager
-Quick Note: Debian Lenny is undergoing Beta/RC testing so these debian installers are currently way out of date, so it will tell you their are unavailable kernel modules, just ignore the question and continue. These modules will be provided later, with the provided linux-image deb.
+User: debian
+pass: temppwd
-To install (ARM EABI) Debian inside QEMU:
+Auto partition resize:
+ cd /opt/scripts/tools
+ git pull
+ ./grow_partition.sh
+ sudo reboot
- sudo qemu-system-arm -M versatilepb -kernel vmlinuz-2.6.26-2-versatile -initrd initrd.gz -m 256 -hda /dev/sdX -append "root=/dev/ram mem=256M"
+Image Updated:
-Note: root/sudo access is required to access /dev/sdX directly (verify mmc card with fdisk -l)
+*2014-10-29
+** Beagle: v3.17.1-armv7-x3 kernel
+*2014-08-13
+** Beagle: v3.16.0-armv7-x4 kernel
-Partition disks, default settings should work for most: Guided - use the largest continuous free space
+Get prebuilt image:
+ wget https://rcn-ee.net/deb/microsd/wheezy/bb-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-[[Image:Beagleboarddebian-partitiondisk.png]]
+Verify Image with:
+ md5sum bb-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
+d02babacae353aae7ae143bd99441  bb-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-==Development PC: Running Debian in QEMU (Optional)==
+Linux:
-Note: This section is only useful for people with out a usb-network device for their beagle who would like to install additional applications, otherwise just skip to the next subsection to install your linux-kernel by copying files from your desktop pc to a SD card.
+ unxz bb-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-As ext3 filesystem support is not included in kernel you will need an initrd, just copy the one installed in the SD card in /boot.
+ sudo dd if=./bb-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX
- sudo qemu-system-arm -M versatilepb -kernel vmlinuz-2.6.26-2-versatile -initrd initrd.img-2.6.26-2-versatile -m 256 -hda /dev/sdX -append "root=/dev/sda2 mem=256M"
+== BeagleBoard xM ==
-Note: Time will be incorrect.
+This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager
- sudo apt-get install ntpdate
+User: debian
- ntpdate pool.ntp.org
+pass: temppwd
-Install default deb packages for linux-image.
+Auto partition resize:
+ cd /opt/scripts/tools
+ git pull
+ ./grow_partition.sh
+ sudo reboot
- Stable  2.6.29
+Image Updated:
- wget http://rcn-ee.net/deb/kernel/beagle/lenny/v2.6.29-58cf2f1-oer44.1/linux-image-2.6.29-oer44.1_1.0lenny_armel.deb
+*2014-10-29
- sudo dpkg -i *.deb
+** Beagle xM: v3.17.1-armv7-x3 kernel
+*2014-08-13
+** Beagle xM: v3.16.0-armv7-x4 kernel
+*2014-07-06
+** repo now enabled (repos.rcn-ee.net/debian)
+** Beagle xM: v3.15.3-armv7-x4 kernel
-Note: It's easier to download these straight to the sd card after you've mounted the SD card to copy uImage to the FAT partition.
+Get prebuilt image:
+ wget https://rcn-ee.net/deb/microsd/wheezy/bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-==Development PC: Linux Kernel Preparation ==
+Verify Image with:
+ md5sum bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
+b44de68b8a0cdce880dd48e3399e  bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-Install uboot-mkimage utility
+Linux:
-  sudo apt-get install uboot-mkimage
+ unxz bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
+  sudo dd if=./bbxm-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX
-Remount SD card, Ubuntu remounts SD card like this:
+== BeagleBone/BeagleBone Black ==
- /media/vfat/ <fat32>
- /media/debian/ <ext3>
-Download Kernel-Image
+This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager
- cd /media/debian/home/<user>/
- wget http://rcn-ee.net/deb/kernel/beagle/lenny/v2.6.29-58cf2f1-oer44.1/linux-image-2.6.29-oer44.1_1.0lenny_armel.deb
-Extract linux-image's vmlinuz-*
+User: debian
- dpkg -x linux-image* ./temp
+pass: temppwd
-Build uboot compatible image and copy to /media/disk/ <fat32 boot partition>
+Auto partition resize:
-  mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 -n "Linux" -d ./temp/boot/vmlinuz-*  /media/vfat/uImage
+ cd /opt/scripts/tools
+ git pull
+  ./grow_partition.sh
+  sudo reboot
-Clean up
+Image Updated:
- rm -rfd temp
+*2014-10-29
+** BeagleBone/BeagleBone Black: v3.14.22-ti-r31 kernel
+*2014-08-13
+** BeagleBone/BeagleBone Black: v3.8.13-bone63 kernel
+*2014-07-06
+** repo now enabled (repos.rcn-ee.net/debian)
+** BeagleBone/BeagleBone Black: v3.8.13-bone59 kernel
+** Black: NOTE: You'll need to hold the BOOT button on powerup...
-Sync, umount Partitions and Install sd card in beagleboard
+Get prebuilt image:
+ wget https://rcn-ee.net/deb/microsd/wheezy/bone-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-== Beagleboard: Setup U-boot for boot ==
+Verify Image with:
+ md5sum bone-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
+ b8079657951abc2350f67797a5aeddb9  bone-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-Insert SD Card and power up Beagleboard.
+Linux:
+ unxz bone-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
+ sudo dd if=./bone-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX
-Using a terminal program, stop u-boot and add these commands:
+== OMAP5432 uEVM ==
- For Linux Kernel 2.6.29 and higher using DSS2
+This image can be written to a 2GB (or larger) microSD card, via 'dd' on linux or on windows: https://wiki.ubuntu.com/Win32DiskImager
- setenv bootcmd 'mmcinit; fatload mmc 0:1 0x80300000 uImage; bootm 0x80300000'
- or
- setenv bootcmd 'mmc init; fatload mmc 0:1 0x80300000 uImage; bootm 0x80300000'
- DVI Port
- setenv bootargs 'console=tty0 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro omapfb.mode=dvi:1280x720MR-16@60'
- Serial Port
- setenv bootargs 'console=ttyS2,115200n8 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro'
- saveenv
- boot
-You shall adapt the resolution to you screen as following :
+User: debian
- omapfb.mode=dvi:1280x720MR-24@60
+pass: temppwd
- Modes:
- "1024x768MR-24@60""800x600-MR24@60" ...
-Here is more explanation on dss video options : [http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=blob;f=Documentation/fb/modedb.txt;h=ec4dee75a35450376ad13442ea926eaf76de76aa;hb=HEAD]
+Auto partition resize:
+ cd /opt/scripts/tools
+ git pull
+ ./grow_partition.sh
+ sudo reboot
-The Beagleboard will reboot 3-4 times while the ext3 filesystem is repaired. (may have to remove power etc)
+Image Updated:
+*2014-10-29
+** OMAP5432 uEVM: v3.14.22-ti-r31 kernel
+*2014-08-13
+** OMAP5432 uEVM: v3.16.0-armv7-lpae-x2 kernel
+*2014-07-06
+** repo now enabled (repos.rcn-ee.net/debian)
+** OMAP5432 uEVM: v3.15.3-armv7-lpae-x5 kernel
-==Debian on Beagleboard==
+Get prebuilt image:
+ wget https://rcn-ee.net/deb/microsd/wheezy/omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-Debian on BeagleBoard uses the following configuration:
+Verify Image with:
+ md5sum omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
+ae762eaae9fc712f19273d4ab61e509  omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
-* Console log = Serial Terminal
+Linux:
-* User Console = HDMI port + usb (keyboard, mouse, etc).
+ unxz omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img.xz
+ sudo dd if=./omap5-uevm-debian-7.7-console-armhf-2014-10-29-2gb.img of=/dev/sdX
-If you want to log in with the serial port, you will have to add to /etc/inittab
-  S:2345:respawn:/sbin/getty 115200 ttyS2
-And if you want to log in as root on the serial port, add ttyS2 to /etc/securetty.
-Note : the beagle board I have was not configured as USB host. I had to modify it to be able to use mouse and keyboards (see [http://elinux.org/BeagleBoard#OTG]). I you do not want to do this, you'll have to install a Vnc server on the beagle to access desktop.
-==Current Issues==
-#Swap disabled: change /dev/hda5 -> /dev/mmcblk0p5 in /etc/fstab (artifact of qemu install to /dev/hdaX)
-#RTC seems to be not enabled: use ntpdate when ethernet works, or issue
- date +"%m%d%y%H%M" -s MMDDYYHHMM
-[[Image:Beagleboarddebian-GNOME.jpg]]
-==Notes==
-#'fbdev' is normally *slow* since it completely relies on the system cpu to update the framebuffer.  Once the video processing core's driver is released this will no longer be an issue.
-# Debian/Gnome actually need the swap to run (up to 90Mo of swap space on my beagle with 128Mo RAM shipped on it) so that it's even slower when using the SD card (try using an external hdd disk).
 = Debian Configuration =
@@ Line 335: / Line 345: @@
 == Serial Ports ==
-Lenny
+To start a login console on ttyO2 (the serial header next to P9), edit /etc/inittab and add:
+ T0:23:respawn:/sbin/getty -L ttyO2 115200 vt102
-edit /etc/inittab and add:
+To start a console on the USB ACM device, add the following to /etc/inittab,
-  S:2345:respawn:/sbin/getty 115200 ttyS2
+  GS0:23:respawn:/sbin/getty -L ttyGS0 115200 vt102
-For root access over the serial port add ttyS2 to /etc/securetty
+==Install Latest Kernel Image==
-== fbdev Drivers ==
+Script:
+  cd /opt/scripts/tools
-/etc/X11/xorg.conf:
+  git pull
-  Section "Device"
- 	Identifier	"Configured Video Device"
- 	Option		"UseFBDev"		"true"
- 	Driver		"fbdev"
- EndSection
-== WiFi ==
-See [[BeagleBoardDebianWifiInstallInfo|BeagleBoard Debian WiFi install info]].
-== Xorg omapfb Drivers ==
-=== Drivers ===
-Note: In Debian this will eventually move from sid to squeeze: http://packages.qa.debian.org/x/xf86-video-omapfb.html  It's too late for lenny.
-Note: These are built with neon optimizations: http://git.debian.org/?p=collab-maint/xf86-video-omapfb.git;a=blob;f=debian/rules;h=c2f0d5391c96c5abb60b1e691ad86bb27e0c17d8;hb=HEAD  (line 48/49)
-lenny:
- wget -c http://rcn-ee.homeip.net:81/dl/deb-sbuild/lenny/xorg-drivers/xserver-xorg-video-omap3_0.1.1-2_armel.deb
- sudo dpkg -i xserver-xorg-video-omap3_0.1.1-2_armel.deb
-squeeze:
- sudo apt-get install xserver-xorg-video-omap3
-=== xorg.conf ===
-/etc/X11/xorg.conf
- Section "Monitor"
-     Identifier "Configured Monitor"
- EndSection
- Section "Screen"
-     Identifier "Default Screen"
-     Device "Configured Video Device"
-     #Limited by SGX?
-     DefaultDepth 16
- EndSection
- Section "Device"
-     Identifier "Configured Video Device"
-     Driver "omapfb"
-     Option "fb" "/dev/fb0"
- EndSection
-Note: Use xvinfo to check if it works:
-  X-Video Extension version 2.2
- screen #0
-   Adaptor #0: "OMAP XV adaptor"
-     number of ports: 1
-     port base: 56
-     operations supported: PutImage
-     supported visuals:
-       depth 16, visualID 0x21
-     number of attributes: 1
-     etc...
-== SGX Video Acceleration ==
-=== Kernel Modules ===
-Lenny:
- wget -c http://rcn-ee.net/deb/kernel/beagle/lenny/v2.6.29-58cf2f1-oer44.1/omaplfb.ko
- wget -c http://rcn-ee.net/deb/kernel/beagle/lenny/v2.6.29-58cf2f1-oer44.1/pvrsrvkm.ko
- sudo mkdir -p /lib/modules/`uname -r`/kernel/drivers/gpu/pvr/
- sudo mv *.ko /lib/modules/`uname -r`/kernel/drivers/gpu/pvr/
- sudo depmod -a omaplfb
-Squeeze:
- wget -c http://rcn-ee.net/deb/kernel/beagle/squeeze/v2.6.29-58cf2f1-oer44.1/omaplfb.ko
- wget -c http://rcn-ee.net/deb/kernel/beagle/squeeze/v2.6.29-58cf2f1-oer44.1/pvrsrvkm.ko
- sudo mkdir -p /lib/modules/`uname -r`/kernel/drivers/gpu/pvr/
- sudo mv *.ko /lib/modules/`uname -r`/kernel/drivers/gpu/pvr/
- sudo depmod -a omaplfb
-Sid:
- wget -c http://rcn-ee.net/deb/kernel/beagle/sid/v2.6.29-58cf2f1-oer44.1/omaplfb.ko
- wget -c http://rcn-ee.net/deb/kernel/beagle/sid/v2.6.29-58cf2f1-oer44.1/pvrsrvkm.ko
- sudo mkdir -p /lib/modules/`uname -r`/kernel/drivers/gpu/pvr/
- sudo mv *.ko /lib/modules/`uname -r`/kernel/drivers/gpu/pvr/
- sudo depmod -a omaplfb
-=== SDK ===
-Make sure to use a "corporate email" : http://software-dl.ti.com/dsps/forms/export.html?prod_no=/OMAP35x_Graphics_SDK_setuplinux_3_00_00_09.bin
-Note: the SDK will not extract directly on any arm platform, extract it first on an x86 machine and tar the resulting folder before transferring to the beagleboard.
+Stable:
+ ./update_kernel.sh
-System Libraries:
+Testing:
-  sudo ln -sf /usr/lib/libXdmcp.so.6.0.0 /usr/lib/libXdmcp.so.0
+  ./update_kernel.sh --beta-kernel
- sudo ln -sf /usr/lib/libXau.so.6.0.0 /usr/lib/libXau.so.0
-SDK install lib/bin from 3.00.00.09:
+Custom: (has to be on rcn-ee.net)
- sudo mkdir /usr/lib/ES2.0
+  ./update_kernel.sh --kernel v3.8.13-bone59
- sudo mkdir /usr/bin/ES2.0
- sudo mkdir /usr/lib/ES3.0
- sudo mkdir /usr/bin/ES3.0
- sudo cp SDK_EXT_DIR/gfx_rel_es2.x/lib* /usr/lib/ES2.0
-  sudo cp SDK_EXT_DIR/gfx_rel_es2.x/p[dv]* /usr/bin/ES2.0
- sudo cp SDK_EXT_DIR/gfx_rel/lib* /usr/lib/ES3.0
- sudo cp SDK_EXT_DIR/gfx_rel/p[dv]* /usr/bin/ES3.0
-Older:
+Reboot with your new Kernel Image.
-SDK lib's
- sudo cp SDK_EXTRACTED_DIR/gfx_rel/*.so /usr/lib/
-SDK pvrsrvinit
+== Xorg Drivers ==
- sudo cp SDK_EXTRACTED_DIR/gfx_rel/pvrsrvinit /usr/bin/
-=== Startup Script ===
-For 3.00.00.09
-/etc/rcS.d/S60pvr.sh
- #!/bin/sh
- if [ "$1" = "" ]; then
- 	echo PVR-INIT: Please use start, stop, or restart.
- 	exit 1
- fi
- if [ "$1" = "stop" -o  "$1" = "restart" ]; then
- 	echo Stopping PVR
- 	rmmod omaplfb 2>/dev/null
- 	rmmod pvrsrvkm 2>/dev/null
- fi
- if [ "$1" = "stop" ]; then
- 	exit 0
- fi
- echo Starting PVR
- modprobe omaplfb
- pvr_maj=`grep "pvrsrvkm$" /proc/devices | cut -b1,2,3`
- if [ -e /dev/pvrsrvkm ] ; then
- 	rm -f /dev/pvrsrvkm
- fi
- mknod /dev/pvrsrvkm c $pvr_maj 0
- chmod 666 /dev/pvrsrvkm
- touch /etc/powervr-esrev
- SAVED_ESREVISION="$(cat /etc/powervr-esrev)"
- ES_REVISION="$(cat /proc/cpuinfo | grep "CPU revision" | awk -F: '{print $2}')"
- if [ "${ES_REVISION}" != "${SAVED_ESREVISION}" ] ; then
- 	echo -n "Starting SGX fixup for"
- 	if [ "${ES_REVISION}" = " 3" ] ; then
- 	echo " ES3.x"
- 	cp -a /usr/lib/ES3.0/* /usr/lib
- 	cp -a /usr/bin/ES3.0/* /usr/bin
- 	else
- 	echo " ES2.x"
- 	cp -a /usr/lib/ES2.0/* /usr/lib
- 	cp -a /usr/bin/ES2.0/* /usr/bin
- 	fi
- 	echo "${ES_REVISION}" > /etc/powervr-esrev
- fi
- /usr/bin/pvrsrvinit
-For Older:
-Need devmem2:
- wget -c http://free-electrons.com/pub/mirror/devmem2.c
- gcc -o devmem2 devmem2.c
- sudo cp devmem2 /usr/local/bin
 Script:
+  cd /opt/scripts/tools/
-/etc/rcS.d/S60pvr.sh
- #!/bin/sh
- modprobe omaplfb
- pvr_maj=`grep "pvrsrvkm$" /proc/devices | cut -b1,2,3`
- if [ -e /dev/pvrsrvkm ] ; then
-     rm -f /dev/pvrsrvkm
- fi
- mknod /dev/pvrsrvkm c $pvr_maj 0
- chmod 666 /dev/pvrsrvkm
- # This is from the SDK...
- /usr/bin/pvrsrvinit
- # Set SGX to full speed
- /usr/local/bin/devmem2 0x48004b40 w 0
-== DSP ==
-= Advanced =
-== Upgrading U-boot  ==
-Using gparted, create a new 50MB Primary fat32 Partition on a blank SD card, or use your existing fat32 partition.
-  cd /media/disk
- sudo wget http://rcn-ee.homeip.net:81/dl/omap/uboot/u-boot-beagleboard-2009.05+r27+gitrd363f9cb0918a1b6b92e2e20d01543d0c4f53274-r27.bin
- sudo mv u-boot-beagleboard-2009.05+r27+gitrd363f9cb0918a1b6b92e2e20d01543d0c4f53274-r27.bin u-boot-f.bin
-Tested --[[User:RobertCNelson|RobertCNelson]] 20:34, 12 August 2009 (UTC) RevB5 + 2.6.29-oer40.5 & RevC2 + 2.6.29-oer40.5
-Insert SD Card, boot Beagleboard and stop U-Boot from booting
- mmcinit (or "mmc init")
- fatload mmc 0 0x80200000 u-boot-f.bin
- nand unlock
- nandecc sw
- nand erase 80000 160000
- nand write.i 0x80200000 80000 160000
- reset
-== Normal Kernel Build ==
-Note, this is done native on the BeagleBoard...
-GIT Checkout, Beagleboard patches, and defconfig.
-Requires:
- sudo aptitude install git-core gcc wget kernel-package fakeroot build-essential
-For this example lets look at: http://cgit.openembedded.org/cgit.cgi/openembedded/commit/?id=5777be68163ae84a340a252e59069d722aa534cb
-http://cgit.openembedded.net/cgit.cgi?url=openembedded/tree/conf/machine/include/omap3.inc&id=5777be68163ae84a340a252e59069d722aa534cb -> "oer44"
-http://cgit.openembedded.net/cgit.cgi?url=openembedded/tree/recipes/linux/linux-omap_2.6.29.bb&id=5777be68163ae84a340a252e59069d722aa534cb -> "GIT" and "PATCHES"
-All build that i do are logged in the build folders: http://rcn-ee.net/deb/kernel/beagle/lenny/v2.6.29-58cf2f1-oer44.1/changes.txt
-(easier to mainitain then the old way)
-===Retrieve the GIT checkout===
-GIT Checkout: 58cf2f1425abfd3a449f9fe985e48be2d2555022 or Shorthand: 58cf2f1
- git-clone git://git2.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
- cd linux-omap-2.6/
- or if you already downloaded it..
- cd linux-omap-2.6/
   git pull
- git checkout 58cf2f1 -b v2.6.29-58cf2f1
- git archive --format=tar --prefix=v2.6.29-58cf2f1/ v2.6.29-58cf2f1 | gzip > ../v2.6.29-58cf2f1.tar.gz
- git checkout master
- git branch v2.6.29-58cf2f1 -D
- cd ..
-===Copy patches and defconfig===
-Open linux-omap**.bb: http://cgit.openembedded.net/cgit.cgi?url=openembedded/tree/recipes/linux/linux-omap_2.6.29.bb&id=5777be68163ae84a340a252e59069d722aa534cb
-This contains 50+ patches need to form a specific (oe) Openembedded release, too keep things neat and simple for my beagle builder, I'll usually combine this into a single diff located here along with the defconfig. http://rcn-ee.homeip.net:81/dl/omap/beagle/v2.6.29-58cf2f1-oer44.1/
- wget http://rcn-ee.homeip.net:81/dl/omap/beagle/v2.6.29-58cf2f1-oer44.1/v2.6.29-58cf2f1-oer44.1.diff
- wget http://rcn-ee.homeip.net:81/dl/omap/beagle/v2.6.29-58cf2f1-oer44.1/defconfig
-=== Build uImage ===
-Extract Kernel Source
- tar -xf v2.6.29-58cf2f1.tar.gz
- cd v2.6.29-58cf2f1/
-Apply Patch
+BeagleBoard/PandaBoard:
-  patch -p1 < ../v2.6.29-58cf2f1-oer44.1.diff
+ cd /opt/scripts/tools/graphics/
+  ./ti-omapdrm.sh
-Copy Defconfig
+BeagleBone/BeagleBone Black:
-  cp ../defconfig .config
+ cd /opt/scripts/tools/graphics/
+  ./ti-tilcdc.sh
-Testing Changes
+== SGX Drivers ==
- make menuconfig
-Build uImage
+=== SGX BeagleBone/BeagleBone Black ===
- make CROSS_COMPILE= uImage
-== Build with make-kpkg ==
+Note, these are FBDEV only, no xorg/x11/etc...
-Note: Use newer or patches/defconfig/git commit from previous section.
+Install sgx modules (3.14.x ti kernel):
+ sudo apt-get install ti-sgx-es8-modules-`uname -r`
+ sudo depmod -a `uname -r`
+ sudo update-initramfs -uk `uname -r`
-===Install Dependencies===
+Build SGX userspace (must be done on an x86, due to the TI 5.01.01.01 blob extractor)
+  git clone https://github.com/RobertCNelson/ti-linux-kernel-dev.git
-  apt-get install git-core kernel-package fakeroot build-essential curl libncurses-dev uboot-mkimage
+  cd ti-linux-kernel-dev/
+ git checkout origin/ti-linux-3.14.y -b tmp-sgx
+ ./sgx_create_package.sh
-===Linux Kernel===
+Copy ./deploy/GFX_5.01.01.01.tar.gz to BeagleBone/BeagleBone Black and install
+ sudo tar xfv GFX_5.01.01.01.tar.gz -C /
+ cd /opt/gfxinstall/
+ sudo ./sgx-install.sh
+ sudo reboot
-  git clone git://git2.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
+Verify omaplfb & pvrsrvkm loaded
-  cd linux-omap-2.6/
+  debian@arm:~$ lsmod | grep omaplfb
-  git checkout -b beagle <git commit>
+  omaplfb                12065  0
+  pvrsrvkm              178782  1 omaplfb
-Patch Kernel with patches you need:
+SGX Demos
-  patch -p1 < ~/dl/patches/*.patch
+  cd /opt/gfxsdkdemos/ogles2/
+ sudo ./OGLES2ChameleonMan
-Setup Kernel .config
+= Building Kernel =
- make CROSS_COMPILE= distclean
-Copy or Make your defconfig
+Note, this section use to have a lot of details, but maintenance of the two wiki's became a pain, so for now on we will just link to my other pages:
- cp ~/dl/defconfig .config
- or
- make CROSS_COMPILE= menuconfig
-Create Debian linux-image* Package
+== Beagle/Beagle xM ==
-  make-kpkg --cross_compile - clean
+  http://eewiki.net/display/linuxonarm/BeagleBoard
- fakeroot make-kpkg --cross_compile - kernel_image
-Create U-boot uImage
+== BeagleBone ==
-  make CROSS_COMPILE= uImage
+  http://eewiki.net/display/linuxonarm/BeagleBone
-== Scripted Kernel Build ==
+== BeagleBone Black ==
+ http://eewiki.net/display/linuxonarm/BeagleBone+Black
-https://launchpad.net/~beagleboard-kernel
+== Panda/Panda ES ==
+ http://eewiki.net/display/linuxonarm/PandaBoard
-Register on launchpad.net, install bzr
+= Upgrading from Debian 5 to Debian 6 =
- sudo apt-get install bzr
-Download SRC (2.6.29)
+[http://www.jeremycole.com/blog/2011/03/09/beagleboard-upgrading-from-debian-5-to-debian-6/ Upgrading] from Debian 5 to Debian 6 report and tutorial.
- bzr branch lp:~beagleboard-kernel/+junk/2.6-stable
-Build Kernel
+= Upgrading from Debian 6 (Squeeze) to Debian 7 (Wheezy) =
- . build_kernel.sh
-Build SGX Modules
+Note, this only goes over "armel" -> "armel"... For users wishing to switch from "armel" -> "armhf" just re-install...
- . build_sgx_modules.sh
-Build Deb File
+ sudo apt-get update ; sudo apt-get upgrade
-  . build_deb.sh
+  sudo sed -i -e "s/squeeze/wheezy/g" /etc/apt/sources.list
+ sudo apt-get update ; sudo apt-get install -y apt aptitude udev dpkg
+ sudo aptitude update ; sudo aptitude -y safe-upgrade ; sudo aptitude -y dist-upgrade

Difference between revisions of "BeagleBoardDebian"

Revision as of 07:50, 30 October 2014

Contents

Help

Official BeagleBoard.org Images for shipping with BeagleBone Black

Recommended Beagle Software

Debian NetInstall

Debian Wheezy

Demo Image

Debian Stable (wheezy)

Debian Testing (jessie)

Flasher

eMMC: BeagleBone Black

raw microSD img

BeagleBoard (classic)

BeagleBoard xM

BeagleBone/BeagleBone Black

OMAP5432 uEVM

Debian Configuration

Serial Ports

Install Latest Kernel Image

Xorg Drivers

SGX Drivers

SGX BeagleBone/BeagleBone Black

Building Kernel

Beagle/Beagle xM

BeagleBone

BeagleBone Black

Panda/Panda ES

Upgrading from Debian 5 to Debian 6

Upgrading from Debian 6 (Squeeze) to Debian 7 (Wheezy)

Navigation menu

Search