Difference between revisions of "BeagleBoard Trainer"
(→ATmega328 (Arduino Hardware Compatible))
(→Prototyping / Breakout Area)
|Line 84:||Line 84:|
== Prototyping / Breakout Area ==
== Prototyping / Breakout Area ==
provides a prototyping / breakout area with a standard 0.1" x 0.1" spacing matrix
to BeagleBoard's level translated signals
to the ATmega328's I/O pins
= PC Board Test Point Locations =
= PC Board Test Point Locations =
Revision as of 14:42, 9 May 2010
- I2C interface(+3.3v or +5v selectable)
- SPI inteface (+3.3v)
- Large prototyping area (0.1" x 0.1" matrix with access to power bus)
- Atmega328 processor (user programmable)
- Arduino compatible
- ATmega328 power is +3.3v or +5v selectable
- Communicate to the ATmega328 via the BeagleBoard's second RS-232 uart
Available from www.tincantools.com
- 1 Hardware
- 2 PC Board Test Point Locations
- 3 PC Board Silkscreen Errata
- 4 Soldering BeagleBoard's Expansion Header
- 5 Creating a bootable SD card in Ubuntu
- 6 Trainer Rev-A Schematic
- 7 Where to purchase the Trainer board
The Trainer provides an interface to the BeagleBoard's I²C port. The I²C signals are level translated to either +3.3V or +5V (user selectable with a jumper). The I²C signals are located next the the prototyping area.
How to access the I2C bus (from software): http://i2c.wiki.kernel.org/index.php/Linux_2.6_I2C_development_FAQ
The Trainer provides an interface the the BeagleBoard's SPI port and the signals are level translated to +3.3V. The SPI signals are located next to the prototyping area.
The Trainer provides an interface to several of the BeagleBoard's GPIO signals. The GPIO signals are level translated to +3.3V and are located next to the prototyping area.
The Trainer board provides an AT24C01 serial EEPROM that contains a Vendor ID and a Device ID that the BeagleBoard uses to identify the type of board connected to the expansion header. This information enables the BeagleBoard to auto-configure the pin mux for signals needed by the Trainer. More information can be found on the Beagle Board Pin Mux Page.
ATmega328 (Arduino Hardware Compatible)
An ATmega328 embedded processor is located on the Trainer board that is user programmable. The ATmega328 is hardware compatible with the Arduino and it's I/O signals are available next to the prototyping area. The ATmega328 can be user jumpered to run at either +3.3V or +5V. One of the BeagleBoard's GPIO signals (GPIO 162) controls the ATmega328's power supply and can turn on or off the power to the ATmega328. The ATmega328 can run off it's internal RC oscillator or it also has an external 8.0 Mhz ceramic resonator.
- Atmel Atmega328 Product Page
- Flash Programming
- Introduction to programming Atmel AVR's under Linux
- Arduino Homepage
- Arduino bootloader compatible with ATmega328 Pro at 8MHz
- Arduino bootloader source can be found at www.arduino.cc
- Arduino bootloader configuration using ISP programmer:
avrdude -c usbtiny -p atmega328p -e -u -U lock:w:0x3f:m -U efuse:w:0x05:m -U hfuse:w:0xda:m -U lfuse:w:0xff:m avrdude -c usbtiny -p atmega328p -U flash:w:ATmegaBOOT_168_atmega328_pro_8MHz.hex -U lock:w:0x0f:m
- AVR code and Arduino sketches can be uploaded using avrdude on the BeagleBoard:
avrdude -V -F -c stk500v1 -p m328p -P /dev/ttyS1 -b 57600 -U flash:w:main.hex
- AVR code and Arduin sketches can be uploaded using avrgal on the BeagleBoard:
Prototyping / Breakout Area
- provides a prototyping / breakout area with a standard 0.1" x 0.1" spacing matrix
- Access to BeagleBoard's level translated signals
- Access to the ATmega328's I/O pins
PC Board Test Point Locations
PC Board Silkscreen Errata
There are errors on four silkscreen labels on the Trainer Rev-A board. The silkscreen for the signals: GP135, GP134, GP133, and GP132 are mislabeled. The correct labels are indicated on the following image:
Soldering BeagleBoard's Expansion Header
This is a quick guide showing you how to solder the 2x14 Header into the BeagleBoard’s Expansion connector (J3).
Insert the 2x14 Header’s SHORT PINS from the back side of the BeagleBoard into the BeagleBoard’s expansion connector (J3).
Position the 2x14 Header so the LONG PINS are on the BACK SIDE of the BeagleBoard.
Solder the SHORT PINS of the 2x14 Header from the TOP SIDE of the BeagleBoard.
Attaching to the BeagleBoard
Attach the four board spacers with the screws provided.
Connect the expansion board onto the BACK SIDE of the BeagleBoard by mating with the 2x14 Header you just soldered. Make sure all of the pins align correctly.
Continue pushing the two boards together until the connectors mate together.
Attach the male standoffs as shown.
Creating a bootable SD card in Ubuntu
This guide will demonstate how to create a dual-partition SD card for the BeagleBoard/Trainer board combination to boot Linux from the first partition and have the root file system located on the second partition.
This guide will use a 2GB SD card for all examples.
Determine which device the SD Card Reader is on your system
Insert the SD Card into the SD Card Reader reader on your Linux PC. Then determine which device it is on your system:
dmesg | tail ... [2079456.496092] sd 34:0:0:0: [sdb] Mode Sense: 03 00 00 00 [2079456.496096] sd 34:0:0:0: [sdb] Assuming drive cache: write through [2079456.513743] sd 34:0:0:0: [sdb] Assuming drive cache: write through [2079456.513751] sdb: sdb1 [2079456.529193] sd 34:0:0:0: [sdb] Assuming drive cache: write through [2079456.529201] sd 34:0:0:0: [sdb] Attached SCSI removable disk
In this case it shows up as /dev/sdb (note sdb insite the square brackets above).
Check to see if the automounter has mounted the SD Card:
df -h Filesystem Size Used Avail Use% Mounted on ... 1.8G 0 1.8G 0% /lib/init/rw /dev/sdb1 1.9G 0 1.9G 0% /media/6262-9331 ...
If mounted, unmount the SD card
sudo fdisk /dev/sdb
Print the partition record:
Command (m for help): p Disk /dev/sdb: 1967 MB, 1967128576 bytes 57 heads, 56 sectors/track, 1203 cylinders Units = cylinders of 3192 * 512 = 1634304 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1204 1920955+ 6 FAT16
Note card size in bytes listed above (in this example: 1967128576). Write this number down, it will be needed later below.
Delete any partitions that are already on the SD card
Command (m for help): d Selected partition 1
Set the Geometry of the SD Card
Go into "Expert mode":
Command (m for help): x
Now we want to set the geometry to 255 heads, 63 sectors and calculate the number of cylinders required for the particular SD card you are using:
Expert command (m for help): h Number of heads (1-256, default 57): 255 Expert command (m for help): s Number of sectors (1-63, default 56): 63 Warning: setting sector offset for DOS compatiblity Expert command (m for help): c Number of cylinders (1-1048576, default 1203): 239
The 239 entered in the cylinders above must be calculated based upon the size of your particular SD card.
Now Calculate the number of Cylinders for your SD card:
number of cylinders = FLOOR (the number of Bytes on the SD Card (from above) / 255 heads / 63 sectors / 512 sector size in bytes )
So for this example: 1967128576 / 255 / 63 / 512 = 239.156427 (use Google to calculate). So we use 239 (i.e. truncate, don't round).
Return to "Normal" mode:
Expert command (m for help): r
Print the partition record to check your work:
Command (m for help): p Disk /dev/sdb: 1967 MB, 1967128576 bytes 255 heads, 63 sectors/track, 239 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System
Create the FAT32 partition for booting and transferring files from your PC
Command (m for help): n Command action e extended p primary partition (1-4) p Partition number (1-4): 1 First cylinder (1-15, default 1): 1 Last cylinder or +size or +sizeM or +sizeK (1-239, default 239): 50 Command (m for help): t Selected partition 1 Hex code (type L to list codes): c Changed system type of partition 1 to c (W95 FAT32 (LBA))
We use 50 cylinders of the total of 239 for the FAT32 partition above. The remainder of the cylinders will be used for the Linux root file system below.
Mark this FAT32 partition as bootable:
Command (m for help): a Partition number (1-4): 1
Create the Linux partition for the root file system
Command (m for help): n Command action e extended p primary partition (1-4) ''p'' Partition number (1-4): 2 First cylinder (51-239, default 51): 51 Last cylinder or +size or +sizeM or +sizeK (51-239, default 239): 239
Print the partition record to check your work
Command (m for help): p Disk /dev/sdb: 1967 MB, 1967128576 bytes 255 heads, 63 sectors/track, 239 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 50 1920955+ c w95 FAT32 (LBA) /dev/sdb2 51 239 83 Linux
Save the new partition records on the SD card
This is an important step. All work up to now has been temporary.
Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. WARNING: If you have created or modified any DOS 6.x partitions, please see the fdisk manual page for additional information. Syncing disks.
Format the partitions
sudo mkfs.msdos -F 32 /dev/sdb1 -n boot mkfs.msdos 3.0.3 (18 May 2009) sudo mkfs.ext3 -L rootfs /dev/sdb2 mke2fs 1.41.9 (22-Aug-2009) Filesystem label=rootfs OS type: Linuxsudo mkfs.ext3 -L rootfs /dev/sdb2 mke2fs 1.41.9 (22-Aug-2009) Filesystem label=rootfs OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) 95040 inodes, 379535 blocks 18976 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=390070272 12 block groups 32768 blocks per group, 32768 fragments per group 7920 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912 Writing inode tables: done Creating journal (8192 blocks): done Writing superblocks and filesystem accounting information: done
Copy files onto the BOOT partition
You will need to download the demo/test files for the BeagleBoard/Trainer board combination:
- MLO (save as MLO)
- u-boot.bin (save as u-boot.bin)
- uImage (save as uImage)
- test.rootfs.tar.gz (save as test.rootfs.tar.gz)
And now copy the first three files onto the boot partition (IMPORTANT: Copy MLO FIRST! because of a bug in the X-loader which causes problems if MLO is not the first file written onto the boot partition).
cp MLO /media/boot/MLO cp u-boot.bin /media/boot/u-boot.bin cp uImage /media/boot/uImage
Copy the files onto the Linux partition
The next step is to extract the files in test-rootfs.tar.gz into the rootfs partition (NOT the boot partition) on the SD card. This can only be done by using Linux.
sudo tar -zxvf test-rootfs.tar.gz -C /media/rootfs
Unmount the SD card from the Linux PC and insert it into the BeagleBoard's SD connector.
Then boot your BeagleBoard while holding down the "User" button.
Trainer Rev-A Schematic
The Trainer Rev-A schematic is avalible here:
Where to purchase the Trainer board
The Trainer board can be purchased from: