Difference between revisions of "DHT-Walnut -Debian Install"

From eLinux.org
Jump to: navigation, search
m (Bot (Edward's framework))
 
m (Fix a wiki link)
 
(3 intermediate revisions by 2 users not shown)
Line 51: Line 51:
 
* When the installer asks you to choose a kernel to install, simply choose one of the provided options.  The kernel will be installed in /boot, but we will not use it with the DHT-Walnut board.  Later, you may remove the /boot directory entirely if you wish.
 
* When the installer asks you to choose a kernel to install, simply choose one of the provided options.  The kernel will be installed in /boot, but we will not use it with the DHT-Walnut board.  Later, you may remove the /boot directory entirely if you wish.
  
* Use the instructions in [wiki:DHT-WalnutBootingFromHdd How to boot from hard disk] to boot from the hard disk. Since in my system, /dev/hda1 contains my kernel image and partition 4 contains the Debian root (/) directory, I use the following commands to boot from the hard disk.
+
* Use the instructions in [[DHT-Walnut_Booting_From_Hdd|How to boot from hard disk]] to boot from the hard disk. Since in my system, /dev/hda1 contains my kernel image and partition 4 contains the Debian root (/) directory, I use the following commands to boot from the hard disk.
  
 
''setenv bootargs console=ttyS0,115200 root=/dev/hda4''
 
''setenv bootargs console=ttyS0,115200 root=/dev/hda4''
Line 58: Line 58:
  
 
Please let me know of any success or problems you encounter by sending an e-mail to [mailto:dale-elinux@farnsworth.org dale-elinux@farnsworth.org] .
 
Please let me know of any success or problems you encounter by sending an e-mail to [mailto:dale-elinux@farnsworth.org dale-elinux@farnsworth.org] .
 +
 +
[[Category:DHT-Walnut]]

Latest revision as of 04:25, 13 April 2011

This page contains information on installing Debian on the DHT-Walnut board.

uImage.2.6.15.4-walnut-debinstall-df4 contains a kernel and a ramdisk containing the Debian Netboot Installer. The installer will download a basic Debian System from the internet and install it to your hard disk. Your DHT-Walnut board must have internet access in order to use this installer.

Download uImage.2.6.15.4-walnut-debinstall-df4 and boot it on your walnut with commands similar to:

setenv bootargs console=ttyS0,115200 root=/dev/ram

tftpboot 1000000 uImage.2.6.15.4-walnut-debinstall-df4 bootm

If you are using a different console device or baudrate, please adjust the bootargs environment variable as required.

After the kernel boots, the Debian Installer will automatically begin and present a series of menus to proceed with the installation.

The Debian Installation Guide for PowerPC is available at http://www.debian.org/releases/stable/powerpc/index.html.en

Since the Debian Installer image used here was not built specifically for the DHT-Walnut board or for the specific kernel being used, the following notes may be helpful.

  • The modules on the Installer image don't match the kernel, so you will see messages like

No kernel modules were found. This probably is due to a mismatch between the kernel used by this version of the installer and the kernel version available in the archive.

This is not a problem, since the needed modules are already built into the kernel.
When this question
 Continue the install without loading kernel modules?
appears, simply answer Yes
  • You may see a message like

Partition disks This partitioner doesn't have information about the default type of the partition tables on your architecture.

If so, answer Yes to this question:
 Continue with partitioning?
  • When partitioning the hard disk, create a small (large enough to hold any kernel image you would want to boot) partition for the kernel image.
  • I have only had success installing the stable (sarge) distribution. testing (etch) and unstable (sid) would not install for me. This isn't really a problem because you can easily upgrade distributions after installing the base system.
  • When the installer asks you to choose a kernel to install, simply choose one of the provided options. The kernel will be installed in /boot, but we will not use it with the DHT-Walnut board. Later, you may remove the /boot directory entirely if you wish.
  • Use the instructions in How to boot from hard disk to boot from the hard disk. Since in my system, /dev/hda1 contains my kernel image and partition 4 contains the Debian root (/) directory, I use the following commands to boot from the hard disk.

setenv bootargs console=ttyS0,115200 root=/dev/hda4 bootdisk 0:1


Please let me know of any success or problems you encounter by sending an e-mail to dale-elinux@farnsworth.org .