Das Oszi Hantek Bootlog

From eLinux.org
Revision as of 06:43, 28 March 2012 by Prpplague (Talk | contribs) (Created page with "Bootlog from UART: <small> ***ARM CPU 400MHz BUS 100MHz (DST1000B bootloader)****(091102) Tekway Bootloader (modify from mizi vivi)v0.10.0 (root@rain-fc4) (gcc version 2.95.3 ...")

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

Bootlog from UART:

***ARM CPU 400MHz BUS 100MHz (DST1000B bootloader)****(091102)
Tekway Bootloader (modify from mizi vivi)v0.10.0 (root@rain-fc4) (gcc version 2.95.3 20010315 (release)) #0.1.4 Tue Dec 1 10:51:38 CST 2009
UPLLCON  : 0x56022
MMU table base address = 0x33DFC000
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung K9D1208V0M)
Found default  parameters
GPfcon :0x5555
Press Return to start the LINUX now, any other key for Bootloader
from : 0x50000, size :0x200000, media_type:0x3
zImage magic = 0x016f2818
Setup linux parameters at 0x30000100
linux command line is: "noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0"
NOW, Booting Linux......
Uncompressing Linux...................................................................................................... done, booting the kernel.
Linux version 2.6.13 (root@rain-fc4) (gcc version 3.4.1) #3 Wed Jun 29 10:13:03 CST 2011
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
Machine: QQ2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
BUG: mapping for 0x19000000 at 0xd0000000 overlaps vmalloc space
S3C2440: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: noinitrd root=/dev/mtdblock2 init=/linuxrc console=ttySAC0
irq: clearing pending ext status 00008000
irq: clearing subpending status 00000002
PID hash table entries: 512 (order: 9, 8192 bytes)
timer tcon=00000000, tcnt a4ca, tcfg 00000200,00000000, usec 00001e57
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 61184KB available (2499K code, 1009K data, 100K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
USB Power Control, (c) 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C2440: Clock Support, UPLL 48.000 MHz
SCSI subsystem initialized
usbcore: registered new driver hub
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
yaffs Jun 29 2011 10:09:19 Installing. 
Initializing Cryptographic API
Console: switching to colour frame buffer device 100x30
S3C24X0 fb0: s3c2410fb frame buffer device initialize done
GPIO L3 bus interface for S3C2440, installed
S3C2410 RTC, (c) 2004 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
Cirrus Logic CS8900A driver for Linux (Modified for SMDK2410)
eth0: incorrect signature 0x0000
Linux video capture interface: v1.00
ovcamchip: v2.27 for Linux 2.6 : OV camera chip I2C driver
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand: mapped registers at c4880000
30 ns is too big for current clock rate 101250
s3c2410-nand: timing: Tacls 0ns, Twrph0 4294ns, Twrph1 0ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00030000 : "bootloader"
0x00050000-0x00250000 : "kernel"
0x00250000-0x03ffc000 : "root"
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
usbcore: registered new driver ov511
drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
usbcore: registered new driver gspca
drivers/usb/media/gspca/gspca_core.c: gspca driver 00.60.00 registered
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
s3c2410 TouchScreen successfully loaded
i2c /dev entries driver
S3C2410_GPECON : 0Xa00002aa , S3C2410_GPEUP: 0X0
open driver log file error!!
dso-i2c: xx install ok
SBC2440 SOUND driver register
SBC2440 SOUND driver probe!
SBC2440 UDA1341 audio driver initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
VFS: Mounted root (yaffs filesystem).
Mounted devfs on /dev
Freeing init memory: 100K
rm: can't remove '/usr/udisk-flag': No such file or directory
dso-iobank: install ok
dso-lcd installed lcd module ok
gpio_major_n = 4, io_minor_n = 4, output 0
kobject_register failed for usb_storage (-17)
insmod: can't insert '/dso/driver/dso-usbstorage.ko': File exists
usb_device: module license 'unspecified' taints kernel.
S3C2410 USB Controller Core Initialized
USB Function Character Driver Interface - 0.5, (C) 2001, Extenex Corp.
usbctl: Opened for usb-char
usbctl: Started for usb-char
usbcore: registered new driver usblp
drivers/dso_drivers/usblp.c: v0.13: USB Printer Device Class driver
fpga bank 11811
dso-fpga: install ok
kobject_register failed for s3c2440-i2c (-17)
dso-i2c: can't register device
insmod: can't insert '/dso/driver/dso-i2c.ko': Device or resource busy
x gpio e: 0xaa0001a6, gpio g :0xfd62f19a , gdata:0x6f8f
dso-spi: install ok
dso-uart: install ok
dso-buzzer: install ok
gpio_major_n = 6, io_minor_n = 12, output 1
fpga download file_name :/dn.rbf
data DOWN finish.
dso-spi:FPGA_DOWNLOAD ok.
no update file to foud
now run app .....
linux kernel version :2.6.13
found /dst* = 

DSTtype= dst1062b
maxSps = 2
bandWidth = 06
bandWidth = 2
###  CheckFileIsExist.  failled.
mkdir: can't create directory '/param': File exists
mkdir: can't create directory '/param/sav': File exists
Kernel version = 0904100...
open all devices......
mmap start addr:0x40373000, phy addr :0x33c80000, mmap size: 0x5e000
readTypeToFile:read ok 0

init kernel event ......[ok].
bank dso 
base volt 400mv=399
base volt 800mv=800
Init Register Run Queue ok
Init Register Run Queue ok
Init Register Run Queue ok
init memory manage....0pWaveMem=(nil)
0get pwaveMem = (nil)..depth=4100
get pwaveMem = 0x40425008
³õʼ»¯²¨ÐÎÄÚ´æ..С³ØÉî¶ÈΪ4100 ÊýÁ¿Îª550 
reg Mem used=0
init calculation magnage param ......arrow position is (0)
init acq wave event......[ok].
init display wave event.....InitDispWaveEvent:0
init wave soft event......ƽ¾ù¿ª¹Ø:0..
init PC_UART_EVENT......[ok].
init SYNC_EVENT......arrow position is (0)
FPGA acq counter acq=203268 delay=0 armed=203252 
msg init start
msg init pt=0xb1c1d0
msg init ok
other show init ok
fpga well configured: fpga version is 0x555583e9
read img languID=1
init_language start
file is Utf_8(including bom)
init_language ok
0auto acq on
init_language start
file is Utf_8(including bom)
init_language ok
menu init ok
msg init start
msg init pt=0xb1c1d0
msg init ok
other show init ok
Status init start
status init ok
arrow show start
arrow show over
1auto acq on
scan mode off
scan mode is off..
init unscan acq
acqmult -used=0
unscan 0 mem valid=548
unscan 1 mem valid=548
Read TDC param from file ok . /tdc_edge125M .
Read TDC param from file ok . /tdc_pulse125M .
Read TDC param from file ok . /tdc_overtime125M .
base volt 8mv=110
base volt 20mv=301
base volt 400mv=399
base volt 800mv=800
write sys.inf ok
init_hardware_io......arrow position is (0)
FPGA acq counter acq=203268 delay=0 armed=203252 
init ....end...2222