Difference between revisions of "Didj U-Boot"

From eLinux.org
Jump to: navigation, search
Line 1: Line 1:
 +
[[Category:Didj]]
 +
 
== Downloads ==
 
== Downloads ==
 
[https://sites.google.com/site/jrspruitt/downloads/u-boot.bin?attredirects=0&d=1 u-boot]
 
[https://sites.google.com/site/jrspruitt/downloads/u-boot.bin?attredirects=0&d=1 u-boot]

Revision as of 12:50, 27 October 2011


Downloads

u-boot

NAND Command Reference

U-Boot provides a single command for interfacing with your NAND storage. It is important to keep in mind when using these commands that 'all values are given in hex, not decimal The general format of the nand command is:

nand <command> [options]

Some of the commands whose functions are understood are listed below.

nand dump

You can dump pages (2K of data) using the nand dump command. The format of the command is

nand dump <page>

Here is an example of using nand dump:

LF1000 # nand dump 0
Page 00000000 dump:
    04 d0 9f e5 01 00 00 eb  6c 0b 00 ea 00 80 22 00
    34 c0 9f e5 01 30 a0 e3  00 30 8c e5 08 30 9c e5
    02 0b a0 e3 04 e0 2d e5  80 30 83 e3 00 e0 a0 e3

nand read

You can read data from the nand into memory using the nand read command. The format of the command is

nand read <address> <nand offset> <size>

Example:

LF1000 # nand read 1800000 0 800

NAND read: device 0 offset 0x0, size 0x800
 2048 bytes read: OK
LF1000 # md 1800000 10
01800000: e59fd004 eb000001 ea000b6c 00228000    ........l.....".
01800010: e59fc034 e3a03001 e58c3000 e59c3008    4....0...0...0..
01800020: e3a00b02 e52de004 e3833080 e3a0e000    ......-..0......
01800030: e1a01000 e3a02b7e e58c3008 e58ce008    ....~+...0......

Comparison of this to the nand dump command above will show that these are the same data. Not that md has dumped the data in little endian format.

nand erase

Disclaimer: This will really erase one or more pages of your nand. Make sure you think this through before doing it.

The nand erase command will reset a range of your nand to its unwritten state. In flash parts, such as Didj, this means all data within an erased page will become 0xFF. The format of the command is:

nand erase <offset> <size>

Example:

LF1000 # nand erase 0 4000

NAND erase: device 0 offset 0x0, size 0x4000
Erasing at 0x0 -- 800% complete.
OK
LF1000 # nand dump 0
Page 00000000 dump:
    ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff
    ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff

It is also important to understand that flash parts cannot erase less than one page. Either the whole page will be erased, or it will not. the size of your erasure should be a multiple of 0x800. In this case I have erased the first 16K of nand, which is where the bootstrap lives.

nand write

Disclaimer: This will write one or more pages to your nand. If those pages have not been erased first, the results will not be what you expect. See disclaimer in the erase nand section.

The nand write command will write a range of pages to your Didj's nand. In flash parts, bits can only be changed from 1 to 0. Therefore it is important to erase the block before you write it. The format of the command is

nand write <memory address> <offset> <size>

Example:

LF1000 # nand write 1800000 0 4000

NAND write: device 0 offset 0x0, size 0x4000
 16384 bytes written: OK

Note that you need to have the data you wish to write already in memory. In the example this data is 16Kbytes starting at physical address 0x1800000.