Difference between revisions of "EBC Exercise 08 Installing Development Tools"

From eLinux.org
Jump to: navigation, search
m (Build a small program)
m (Download and Compile the Kernel)
Line 156: Line 156:
Exit gedit and do the following:
Exit gedit and do the following:
  host$ '''source ~/.oe/environment-oecore'''
  host$ '''source ~/.oe/environment-angstromv2012.05'''
  host$ '''cd ~/BeagleBoard/oe'''
  host$ '''cd ~/BeagleBoard/oe'''
  host$ '''bitbake virtual/kernel'''
  host$ '''bitbake virtual/kernel'''
Mine says it has 1032 tasks to do.  It took about XX hours to do them.  Once done you should get a kernel that will work.
Mine says it has 769 tasks to do.  It took about XX hours to do them.  Once done you should get a kernel that will work.
If you accidentally run bitbake without commenting out the above line, after it runs you can comment out the INHERIT line and then run
If you accidentally run bitbake without commenting out the above line, after it runs you can comment out the INHERIT line and then run

Revision as of 18:20, 31 August 2012

thumb‎ Embedded Linux Class by Mark A. Yoder

Early in the class most of the exercises we will do will all run on the BeagleBoard. You'll be able to edit (gedit), compile (gcc) and run all on the Beagle. Later, when we start compiling the kernel [1] or the boot loader, (U-boot) you will need to cross compile on a Linux machine and copy the results to the Beagle.

The purpose of this exercise is to install all the tools needed for compiling on your host so they will be ready when you need them.

Instructions for building Ångström are given here; however there are a few changes you have to make. Here's what I did.

Install development environment

The step is to get the crosscompilers, etc. installed. Generally you do this install on your local copy of Linux. Some of these installs can take a long time (one took me 12 hours, slow download times), so you may want to install on a remote server that's always connected to the internet. If so, see the tips [[ | below]]

Get the setup scripts

First install git by running the following on your host computer.

host$ sudo apt-get install git-core

(Here is a nice git tutorial. Take a look at it if you want to understand the commands that follow. We'll explore it in more depth in a later exercise.)

Then run the following to load the meta data.

I have everything in a ~/BeagleBoard, so here is how I setup things:

host$ cd
host$ mkdir -p BeagleBoard
host$ cd BeagleBoard
host$ git clone git://github.com/Angstrom-distribution/setup-scripts.git oe
host$ cd oe

(The git took 4.5 seconds.) This creates a directory for open embedded (oe) and gets the script to download Ångström. What files do you see?

Setting up for the BeagleBoard

Now let's setup local.conf for our needs:

$ gedit conf/local.conf

Add the following to the end of the file.

MACHINE ?= "beagleboard" 

Look at this block of lines:

# Make use of SMP and fast disks

Here you can tell it how many parallel threads to run. If you have several cores on your machine, make this number big. If you have only one core, you might be better performance setting it to 1. If you have no clue which value to pick, Gentoo users suggest 1 more than the number of cores in your computer. More details are here.

  • PARALLEL_MAKE sets the number "gcc" threads (same as make -j4 at compile time
  • BB_NUMBER_THREADS sets the number of bitbake threads, (one thread can be downloading, while another compiles)

To save you a lot of time, it is useful to disable locale generation for all but the one you need. Add this to local.conf

GLIBC_GENERATE_LOCALES = "en_US.UTF-8 en_GB.UTF-8 de_DE.UTF-8 fr_FR.UTF-8 pt_BR.UTF-8 es_ES.UTF-8 kn_IN.UTF-8 ml_IN.UTF-8 ta_IN.UTF-8"

Now run:

host$ ./oebb.sh config beagleboard

I got some errors; some things are missing

host$ ls -ls /bin/sh
0 lrwxrwxrwx 1 root root 4 Mar 29 14:53 /bin/sh -> dash
host$ sudo rm /bin/sh
host$ sudo ln -s /bin/bash /bin/sh
host$ ls -ls /bin/sh
0 lrwxrwxrwx 1 root root 9 Aug 30 10:38 /bin/sh -> /bin/bash
host$ sudo apt-get install gawk

Now try again

host$ ./oebb.sh config beagleboard
host$ ./oebb.sh update

This will bring in all the tools you need. The config took about 3.5 minutes on my machine, update took about 1 minute.

Build a small program

Before the first time you run bitbake you need to do the following to set up the environmental variables:

host$ source ~/.oe/environment-angstromv2012.05

Take a look in the file and see what it is doing.

host$ less ~/.oe/environment-angstromv2012.05

To see if everything is ready, run the following

host$ bitbake nano

nano is a small editor. We really don't need nano, but if it can be compiled we know we have everything in place. I get the following error when I run the bitbake:

Pseudo is not present but is required, building this first before the main build
ERROR:  Poky's config sanity checker detected a potential misconfiguration.
    Either fix the cause of this error or at your own risk disable the checker (see sanity.conf).
    Following is the list of potential problems / advisories:

    Please install following missing utilities: diffstat,texi2html,makeinfo,cvs,svn,chrpath

ERROR: Execution of event handler 'check_sanity_eventhandler' failed

So, some programs are missing. Install them with:

host$ sudo apt-get install diffstat texi2html texinfo subversion chrpath gettext

This took just a few minutes.

Now run:

host$ bitbake nano

This will take a while. Mine first said it has 77 tasks to do. Once those were done it had 1113 tasks.

Below is a table of the times from last year. Add your bitbake time to this year's table.

Initial bitbake nano Winter 2011-2012 runtimes
Processor Settings Run Time
8 Core virtual machine PARALLEL_MAKE = "-j8"
2.5 hours
Intel Core 2 Duo T7800, 2.60 GHz PARALLEL_MAKE = "-j2"
Initial bitbake nano 2011 runtimes
Processor Settings Run Time
Dell E521 with AMD Athlon 64 dual-core PARALLEL_MAKE = "-j4"
Psyco? Yes.
1.5 hours
Intel Core 2 Duo T7800, 2.60 GHz PARALLEL_MAKE = "-j1"
Psyco? No.
Intel Core 2 Duo T7800, 2.60 GHz PARALLEL_MAKE = "-j4"
Psyco? Yes.
Ubuntu 10.04 Running in VMWare Workstation 7.1.3 Under Windows 7 32-bit

Once nano is done building you can find it with:

host$ find . -name nano

Can you figure out which one is the nano that will run on your Beagle? I found it here:


Download and Compile the Kernel

The next step is to download and compile the kernel.

We want to keep the kernel source code around so we can experiment with it. Do this:

host$ gedit conf/local.conf

Find the line near the top that says INHERIT += " rm_work " and comment it out. This will save the source code.

# INHERIT += " rm_work

Exit gedit and do the following:

host$ source ~/.oe/environment-angstromv2012.05
host$ cd ~/BeagleBoard/oe
host$ bitbake virtual/kernel

Mine says it has 769 tasks to do. It took about XX hours to do them. Once done you should get a kernel that will work.

If you accidentally run bitbake without commenting out the above line, after it runs you can comment out the INHERIT line and then run

host$ bitbake -c clean virtual/kernel
host$ bitbake -f -c compile virtual/kernel

This second run should take less time (one timing: first run took 3.5 hours; the recompiling took 25 minutes).

Finding the Correct Kernel

When you do the bitbake virtual/kernel you get the most recent kernel. How do you know which version you got? Look in the source directory.

host$ cd ~/BeagleBoard/oe; ls -F
build/  conf/  oebb.sh*  pseudodone  scripts/  sources/

Take a look in the sources directory.

host:~/BeagleBoard/oe$ ls -F sources
bitbake/        meta-efikamx/   meta-nslu2/         meta-smartphone/
downloads/      meta-ettus/     meta-openembedded/  meta-ti/
layers.txt      meta-handheld/  meta-openpandora/   meta-xilinx/
meta-angstrom/  meta-intel/     meta-opie/          openembedded-core/

Here you see directories that contain information about various repositories that were used in pulling together all the sources used to build the kernel, u-boot, and the cross-compilers. Look around a bit an see what you can learn.

Let's see what was built when we made the kernel.

host:~/BeagleBoard/oe$ cd build; ls -F
sstate-cache/  tmp-angstrom_2010_x-eglibc/

We are interested in the second directory. This is where the Angstrom build is kept, it's the 2010 version. Open Embedded can support other distributions and the software is set up so you can can work with more than one distribution as the time. We're only working with Angstrom though.

The x-eglibc tells us what libraries were used in making the build. We'll talk about libraries later. Look further:

host:~/BeagleBoard/oe/build$ cd tmp-angstrom_2010_x-eglibc/; ls -F
abi_version  ccache/   qa.log           stamps/    work-shared/
buildstats/  deploy/   saved_tmpdir     sysroots/
cache/       pkgdata/  sstate-control/  work/

I'm not sure what all of these are for, but I know the cross-compilers are kept in sysroots. Go and explore. See if you can find them. We'll work with them in a later exercise. What we want is in the work directory:

host:~/BeagleBoard/oe/build/tmp-angstrom_2010_x-eglibc$ cd work; ls -F
all-angstrom-linux/             beagleboard-angstrom-linux-gnueabi/
armv7a-angstrom-linux-gnueabi/  x86_64-linux/

These directories contain tools based on what they work on. x86_64-linux, for example, has the tools that run on your host computer. armv7a-angstrom-linux-gnueabi has things that run on all arm processors. beagleboard-angstrom-linux-gnueabi has things that are Beagle specific, and that's where we find the kernel.

host:~/BeagleBoard/oe/build/tmp-angstrom_2010_x-eglibc/work$ cd beagleboard-angstrom-linux-gnueabi/; ls -F
linux-3.0.9-r110a/ shadow- u-boot-2011.09-r4/

It looks like we have the 3.0.9 version of the kernel. Here's how you find out what kernel version have we've been running on the Beagle. On the Beagle run:

beagle$ uname -a
Linux beagleboard 2.6.32 #3 PREEMPT Tue May 10 10:06:15 CEST 2011 armv7l GNU/Linux

It looks like we're running the 2.6.32 kernel. But what if you don't want the most recent kernel? You need to find the bitbake recipe for the kernel you are running. Here's how I did it, back to the host:

host$ cd ~/BeagleBoard/oe
host$ find . -name "*2.6.32*" | grep recipe

The find command looks for files and directories that contain the string 2.6.32, the grep command then displays only those that contain the string recipe in the name. What you find is the the name of the recipe for building the kernel we're interested in. Now all you have to do is bitbake it. Be sure the conf/local.conf file is set as described earlier so that the sources aren't deleted.

host$ source ~/.oe/environment-oecore
host$ bitbake linux-omap-psp-2.6.32

I think mine took a couple of hours.

Download and Compile U-boot

While were' at it, let's get the boot loader we'll be using...

$ bitbake u-boot

I think this took a half hour or so.

Once installed you are ready for kernel work.

Installing on a Remove Machine

Installing the cross development tools and the kernel on a laptop is nice, but sometimes the downloads are too long for such a portable device. I've had a bitbake run some 12 hours. Another option is to use a remote machine. In my case our CSSE department has created a virtual machine with Ubuntu 10.4 installed on it.

To install on a remote machine are the same as above; However here's a couple of tips to make it easier.

First, ssh to the remote machine. Assume the machine is called csse and your login name is beagle.

local$ ssh -CX beagle@csse

You can leave the beagle@ off if you have the same login on both machine. The -C says to compress everything that's moved between the machines over the network. This is good for slow connections. The X says to pass the X11 display information to the remote machine. This way you can run graphical programs, such as gedit, on the remote machine and the graphics will display on your local machine (assuming you are running X11 on your local machine).

If you are sshing a lot check out the tip here about suspending ssh and the tip here about authorizing ssh so you don't have to enter your password every time.

Once logged on to the removed machine run

remote$ sudo apt-get install byobu

This installs byobu which is a program that lets you connect to the same shell from multiple machines. Once installed run

remote$ byobu

You'll see something like:

Screenshot-beagle@ubu-may - byobu.png

So what? Run a couple of commands, like ls or who, then hit F6. This will suspend your session. Now run byobu again. You'll be back in the same session. The session keeps running, even when you aren't connected.

Do you see the use?

  • Fire up byobu
  • Start a long bitbake
  • Once you are sure it running OK, hit F6 and go home.
  • From home fire up byobu and you'll see your bitbake (probably still running).
  • You can F6 and check on it later.

Try opening another terminal and running byobu in both terminals. You'll see the same thing in both.


$ man byobu

to see what it can do. Here's a list of shortcuts:

      F2 - Create a new window
      F3 - Move to previous window
      F4 - Move to next window
      F5 - Reload profile
      F6 - Detach from this session
      F7 - Enter copy/scrollback mode
      F8 - Re-title a window
      F9 - Configuration Menu
      F12 -  Lock this terminal
      Ctrl-a $ - show detailed status
      Ctrl-a R - Reload profile
      Ctrl-a ! - Toggle key bindings on and off
      Ctrl-a k - Kill the current window

But there is much more. Go and explore.

thumb‎ Embedded Linux Class by Mark A. Yoder