Difference between revisions of "EBC Exercise 23 Configuring the Kernel"

From eLinux.org
Jump to: navigation, search
(Finding the kernel sources: Updated for non=bitbake version)
m (Making and Installing the kernel: Removed)
 
(20 intermediate revisions by 5 users not shown)
Line 2: Line 2:
 
[[Category:BeagleBoard]]
 
[[Category:BeagleBoard]]
 
{{YoderHead}}
 
{{YoderHead}}
 +
{{EBC3.8}}These instructions are for the 3.8 kernel. See [[EBC Exercise 23 Configuring the Kernel - bitbake]] for the 3.2 kernel.
  
In a previous exercise ([[EBC Exercise 22 Cross-Compiling and Finding the Right Kernel]]) you learned how to get and compile the kernel.  Here we'll look at configuring it.
+
In a previous exercises ([[EBC Exercise 08a Cross-Compiling]] and [[EBC Exercise 08 Installing Development Tools]]) you learned how to get and compile the kernel.  Here we'll look at configuring it.
  
 
== Finding the kernel sources ==
 
== Finding the kernel sources ==
Line 9: Line 10:
 
First set up the environment and go to the kernel directory
 
First set up the environment and go to the kernel directory
  
  host$ '''source ~/.oe/crossCompileEnv.sh'''
+
  host$ '''source ~/crossCompileEnv.sh''' (set up in [[EBC Exercise 08a Cross-Compiling]])
  host$ '''cd ~/BeagleBoard/kernel'''
+
  host$ '''cd ~/BeagleBoard/linux-dev/KERNEL'''
  
 
== Getting kernel make help ==
 
== Getting kernel make help ==
Line 56: Line 57:
  
 
I had to run the following to get these to work.
 
I had to run the following to get these to work.
  host$ '''sudo apt-get install libncurses5-dev'''
+
  host$ '''sudo apt install libncurses5-dev'''
  host$ '''sudo apt-get install qt3-dev-tools'''
+
  host$ '''sudo apt install qt4-dev-tools'''
  host$ '''sudo apt-get install libglade2-dev'''
+
  host$ '''sudo apt install libglade2-dev'''
 +
 
 +
== Recovering ==
 +
If your Beagle fails to boot, follow the [[EBC_Exercise_22_Recovering]] instructions to recover.
  
 
{{YoderFoot}}
 
{{YoderFoot}}

Latest revision as of 12:28, 20 September 2019

thumb‎ Embedded Linux Class by Mark A. Yoder


3.8 Kernel

These instructions are for the 3.8 kernel. See EBC Exercise 23 Configuring the Kernel - bitbake for the 3.2 kernel.

In a previous exercises (EBC Exercise 08a Cross-Compiling and EBC Exercise 08 Installing Development Tools) you learned how to get and compile the kernel. Here we'll look at configuring it.

Finding the kernel sources

First set up the environment and go to the kernel directory

host$ source ~/crossCompileEnv.sh  (set up in EBC Exercise 08a Cross-Compiling)
host$ cd ~/BeagleBoard/linux-dev/KERNEL

Getting kernel make help

Once there try some of the make commands. Help is a good place to start.

host$ make help | less
Cleaning targets:
  clean           - Remove most generated files but keep the config and
                    enough build support to build external modules
  mrproper        - Remove all generated files + config + various backup files
  distclean       - mrproper + remove editor backup and patch files

Configuration targets:
  config          - Update current config utilising a line-oriented program
  menuconfig      - Update current config utilising a menu based program
  xconfig         - Update current config utilising a QT based front-end
  gconfig         - Update current config utilising a GTK based front-end
...

This produces a list of common make targets.

Finding and installing support software

There are several ways to configure the kernel. make config will prompt you line-by-line for each of the settings, very tedious, not recommended. Try

host$ make menuconfig
 *** Unable to find the ncurses libraries or the
 *** required header files.
 *** 'make menuconfig' requires the ncurses libraries.
 *** 
 *** Install ncurses (ncurses-devel) and try again.
 *** 
make[1]: *** [scripts/kconfig/dochecklxdialog] Error 1
make: *** [menuconfig] Error 2

If you get the error above, you need to install the ncurses library. Here are notes on how to discover what to install and installing it.

NOTE FOR UBUNTU USERS: 'sudo apt-get install libncurses5-dev' without quotes will install ncurses

Configuring the kernel

Try the various interfaces for configuring the kernel.

host$ make menuconfig
host$ make xconfig
host$ make gconfig

I had to run the following to get these to work.

host$ sudo apt install libncurses5-dev
host$ sudo apt install qt4-dev-tools
host$ sudo apt install libglade2-dev

Recovering

If your Beagle fails to boot, follow the EBC_Exercise_22_Recovering instructions to recover.




thumb‎ Embedded Linux Class by Mark A. Yoder