Flameman/routerstation-pro/dmesg

From eLinux.org
Jump to: navigation, search

dmesg

2.6.37.my

sion is: 00019374 (MIPS 24Kc)
SoC: Atheros AR7161 rev 2
Clocks: CPU:720.000MHz, DDR:360.000MHz, AHB:180.000MHz, Ref:40.000MHz
Determined physical RAM map:
 memory: 08000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00008000
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat 8058f5e0, node_mem_map 81000000
  Normal zone: 256 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 32512 pages, LIFO batch:7
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: root=/dev/sdb4 console=ttyS0,115200 init=/bin/bash rootdelay=2 fbcon=font:VGA8x16,scrollback:32k,map:0,rotate:0 board=UBNT-RSPRO
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00002002
Readback ErrCtl register=00002002
Memory: 123904k/131072k available (3816k kernel code, 7168k reserved, 1498k data, 176k init, 0k highmem)
SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:80
fbdummycon: startup
fbdummycon: init
dummyfb: 60x25 vc_can_do_color=1
Console: colour fbdummy 60x25
Calibrating delay loop... 479.23 BogoMIPS (lpj=2396160)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
devtmpfs: initialized
NET: Registered protocol family 16
this MIPS machine is my Ubiquiti RouterStation Pro
registering PCI controller with io_map_base unset
ar71xx: using random MAC address for eth0
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: [0700:1107] type 0 class 0x000000
pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0fffffff pref]
pci 0000:00:00.0: reg 14: [io  0x0000-0x00ff]
pci 0000:00:00.0: supports D1 D2
pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:00.0: PME# disabled
pci 0000:00:12.0: [168c:0029] type 0 class 0x000280
pci 0000:00:12.0: reg 10: [mem 0x00000000-0x0000ffff]
pci 0000:00:12.0: PME# supported from D0 D3hot
pci 0000:00:12.0: PME# disabled
pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
pci 0000:00:12.0: BAR 0: set to [mem 0x10000000-0x1000ffff] (PCI address [0x10000000-0x1000ffff])
PCI: mapping irq 73 to pin1@0000:00:12.0
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource MIPS
FS-Cache: Loaded
CacheFiles: Loaded
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 0 bytes, default 32
msgmni has been set to 242
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled
loop: module loaded
lkdtm: No crash points registered, enable through debugfs
Atheros AR71xx SPI Controller driver version 0.2.4
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
eth0: connected to PHY at ag71xx-mdio:04 [uid=004dd041, driver=Atheros AR8216/AR8316]
eth1: Atheros AG71xx at 0xba000000, irq 5
eth1: AR8316 switch driver attached.
ar8316: Using port 4 as PHY
eth1: connected to PHY at ag71xx-mdio:00 [uid=004dd041, driver=Atheros AR8216/AR8316]
PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
ath: EEPROM regdomain: 0x809c
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x52
ath: Country alpha2 being used: CN
ath: Regpair used: 0x52
cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (N/A mBi, 2000 mBm)
cfg80211: Disabling freq 2467 MHz as custom regd has no rule that fits a 20 MHz wide channel
cfg80211: Disabling freq 2472 MHz as custom regd has no rule that fits a 20 MHz wide channel
cfg80211: Disabling freq 2484 MHz as custom regd has no rule that fits a 20 MHz wide channel
cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (600 mBi, 2000 mBm)
cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
cfg80211: 2474000 KHz - 2494000 KHz @  KHz), (600 mBi, 2000 mBm)
ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
cfg80211: Pending regulatory request, waiting for it to be processed...
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=73
usbcore: registered new interface driver ath9k_htc
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ar71xx-ohci ar71xx-ohci: Atheros AR71xx built-in OHCI controller
ar71xx-ohci ar71xx-ohci: new USB bus registered, assigned bus number 1
ar71xx-ohci ar71xx-ohci: irq 14, io mem 0x1c000000
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Atheros AR71xx built-in OHCI controller
usb usb1: Manufacturer: Linux 2.6.39-flesh-eating-bats-ubiquiti ohci_hcd
usb usb1: SerialNumber: ar71xx-ohci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver wusb-cbaf
usbcore: registered new interface driver uas
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
rtc-pcf2123 spi0.1: chip found, driver version 0.6
rtc-pcf2123 spi0.1: spiclk 1000 KHz.
rtc-pcf2123 spi0.1: rtc core: registered rtc-pcf2123 as rtc0
Atheros AR71xx hardware watchdog driver version 0.1.0
ar71xx-wdt: timeout=15 secs (max=23)
TCP westwood registered
NET: Registered protocol family 17
net: 802.1Q VLAN Support v1.8
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
lib80211_crypt: registered algorithm 'WEP'
lib80211_crypt: registered algorithm 'CCMP'
lib80211_crypt: registered algorithm 'TKIP'
rtc-pcf2123 spi0.1: setting system clock to 1980-03-23 09:27:57 UTC (322651677)
Waiting 2sec before mounting root device...
usb 1-1: new full speed USB device number 2 using ar71xx-ohci
usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: Product: USB2.0 Hub
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-2: new full speed USB device number 3 using ar71xx-ohci
usb 1-2: New USB device found, idVendor=05e3, idProduct=0723
usb 1-2: New USB device strings: Mfr=3, Product=4, SerialNumber=2
usb 1-2: Product: USB Storage
usb 1-2: Manufacturer: Generic 
usb 1-2: SerialNumber: 000000009454
scsi0 : usb-storage 1-2:1.0
usb 1-1.2: new full speed USB device number 4 using ar71xx-ohci
usb 1-1.2: New USB device found, idVendor=07ff, idProduct=00ff
usb 1-1.2: New USB device strings: Mfr=10, Product=11, SerialNumber=5
usb 1-1.2: Product: USB20
usb 1-1.2: Manufacturer: USBID
usb 1-1.2: SerialNumber: 5DB072272222
scsi1 : usb-storage 1-1.2:1.0
usb 1-1.4: new full speed USB device number 5 using ar71xx-ohci
usb 1-1.4: New USB device found, idVendor=0011, idProduct=7788
usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.4: Product: Mass Storage
usb 1-1.4: Manufacturer: Generic
usb 1-1.4: SerialNumber: 0BB7F18A
scsi2 : usb-storage 1-1.4:1.0
scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   9454 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] 15523840 512-byte logical blocks: (7.94 GB/7.40 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1 sda2 sda3
scsi 1:0:0:0: Direct-Access     ST310211 A                     PQ: 0 ANSI: 2 CCS
sd 1:0:0:0: [sdb] 19746720 512-byte logical blocks: (10.1 GB/9.41 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 38 00 00
sd 1:0:0:0: [sdb] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 1:0:0:0: [sdb] Assuming drive cache: write through
 sdb: [mac] sdb1 sdb2 sdb3 sdb4
sd 1:0:0:0: [sdb] Assuming drive cache: write through
sd 1:0:0:0: [sdb] Attached SCSI disk
EXT3-fs (sdb4): recovery required on readonly filesystem
EXT3-fs (sdb4): write access will be enabled during recovery
EXT3-fs: barriers not enabled
scsi 2:0:0:0: Direct-Access     Generic  Flash Disk       8.00 PQ: 0 ANSI: 2
sd 2:0:0:0: [sdc] 8192000 512-byte logical blocks: (4.19 GB/3.90 GiB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] Assuming drive cache: write through
 sdc: [mac] sdc1 sdc2
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] Attached SCSI removable disk
EXT3-fs (sdb4): recovery complete
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sdb4): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:20.
devtmpfs: mounted
Freeing unused kernel memory: 176k freed
FPU: CPU has no floating point unit
FPU: IEEE754 floating MIPS floating point support provided as kernel float emulation
FPU: you'll get much better performance by compiling with -msoft-float!
EXT3-fs (sdb4): using internal journal
Adding 524284k swap on /dev/sdb3.  Priority:-1 extents:1 across:524284k 
ar71xx: pll_reg 0xb8050010: 0x1099
eth0: link up (100Mbps/Full duplex)
usb 1-1.3: new full speed USB device number 6 using ar71xx-ohci
usb 1-1.3: New USB device found, idVendor=059f, idProduct=1053
usb 1-1.3: New USB device strings: Mfr=2, Product=3, SerialNumber=1
usb 1-1.3: Product: P'9230 Desktop Drive
usb 1-1.3: Manufacturer: LaCie
usb 1-1.3: SerialNumber: 00000000d4ca9f79203e
scsi3 : usb-storage 1-1.3:1.0
scsi 3:0:0:0: Direct-Access     ST2000DL 001-9VT156       CC41 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Mode Sense: 23 00 00 00
sd 3:0:0:0: [sdd] Assuming drive cache: write through
sd 3:0:0:0: [sdd] Assuming drive cache: write through
 sdd: [mac] sdd1 sdd2 sdd3 sdd4 sdd5 sdd6
sd 3:0:0:0: [sdd] Assuming drive cache: write through
sd 3:0:0:0: [sdd] Attached SCSI disk
EXT3-fs: barriers not enabled
EXT3-fs (sdd4): warning: checktime reached, running e2fsck is recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sdd4): using internal journal
EXT3-fs (sdd4): recovery complete
EXT3-fs (sdd4): mounted filesystem with writeback data mode
EXT3-fs (sdb4): using internal journal
EXT3-fs: barriers not enabled
EXT3-fs (sdd4): warning: checktime reached, running e2fsck is recommended
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sdd4): using internal journal
EXT3-fs (sdd4): mounted filesystem with writeback data mode

Launching bash as the first Process ...

mips32-routerboard-pro / # 

note