Hammer Board Hardware - Revision history

FransMeulenbroeks: removed ref to nonexisting page (adc)

2008-11-17T20:24:33Z

removed ref to nonexisting page (adc)

FransMeulenbroeks at 08:59, 15 November 2008

2008-11-15T08:59:22Z

Robotguy: /* Hammer-RDP */

2008-08-04T15:20:11Z

‎ Hammer-RDP

Robotguy: /* Hammer-RDP */

2008-08-04T15:19:11Z

‎ Hammer-RDP

Robotguy: /* Hammer Board (the 40 pin DIP module) */

2008-08-04T15:13:06Z

‎Hammer Board (the 40 pin DIP module)

Robotguy: /* Hammer Board Pinouts */

2008-08-04T15:11:45Z

‎Hammer Board Pinouts

Robotguy: /* Hammer Board Photos */

2008-08-04T15:11:22Z

‎Hammer Board Photos

Robotguy: /* Hammer Board Description */

2008-08-04T15:11:05Z

‎Hammer Board Description

Robotguy: /* Hammer-RDP */

2008-08-04T03:11:53Z

‎ Hammer-RDP

Robotguy: /* Hammer-RDP */

2008-08-04T03:11:15Z

‎Hammer-RDP

@@ Line 89: / Line 89: @@
 |33|| AIN1||ADC input 1|| ||(Note - these ADCs are independant, and do not support differential mode)
 |- style="background:red"
-|34|| AIN0||[[ADC]] input 0
+|34|| AIN0||ADC input 0
 |- style="background:#30FFFF"
 |35|| DP1||USB 1 Slave +

@@ Line 87: / Line 87: @@
 |32||style="background:#FF80FF" |EINT13||style="background:#FF80FF" |External interrupt 13||style="background:#AAA0FF" |SPIMISO1||style="background:#AAA0FF" |SPI port 1 MISO
 |- style="background:red"
-|33|| AIN1||[[ADC]] input 1|| ||(Note - these ADCs are independant, and do not support differential mode)
+|33|| AIN1||ADC input 1|| ||(Note - these ADCs are independant, and do not support differential mode)
 |- style="background:red"
 |34|| AIN0||[[ADC]] input 0

@@ Line 104: / Line 104: @@
 |}
-== [[Hammer_RDP| Hammer-RDP]] ==
+== Hammer-RDP ==
 Hammer-RDP stands for Hammer '''R'''obotics '''D'''evelopment '''P'''latform. This is a new carrier board for Hammer being developed by TinCanTools for the Robotics, Process Control, and the general interfacing and hobbiest market. The Hammer-RDP is ideal for tinkering with sensors, servos, and whatever else you might want to connect to Hammer, since it provides both 3.3V and 5V selectable pin sections.

← Older revision		Revision as of 15:19, 4 August 2008
Line 105:		Line 105:

	== [[Hammer_RDP\| Hammer-RDP]] ==		== [[Hammer_RDP\| Hammer-RDP]] ==
		+
		+	Hammer-RDP stands for Hammer '''R'''obotics '''D'''evelopment '''P'''latform. This is a new carrier board for Hammer being developed by TinCanTools for the Robotics, Process Control, and the general interfacing and hobbiest market. The Hammer-RDP is ideal for tinkering with sensors, servos, and whatever else you might want to connect to Hammer, since it provides both 3.3V and 5V selectable pin sections.
		+
		+	'''Please NOTE:''' You must jumper select each four pin section on Hammer-RDP for either 3.3V or 5V operation, and connecting a 5V device to a pin jumpered for 3.3V operation will most likely damage the [[Hammer_Board\|Hammer Board]].
		+
		+	Main Features:
		+
		+	* Small size - just 3" x 3", ideal for space constrained applications.
		+	* Stackable add on boards can be created for custom applications such as process control, home automation, robotics, etc.
		+	* Three pin headers for all GPIO connections, allowing easy interfacing to sensors, servos, and other devices using this pin arrangement.
		+	* Jumperable dual voltage selection for all GPIO connections - 3.3V or 5V. Pins can be jumpered for either voltage in sets of four.
		+	* Dual voltage (3.3V and 5V) I2C bus.
		+	* 8 channel, 12 bit analog inputs via SPI
		+	* Most Hammer signals, including I2C and USB, are available on the stacking connector.
		+
		+	Possible add on boards you might create for the Hammer-RDP:
		+
		+	* Prototyping Board
		+	* Single USB Host 4 port Hub with on board Flyswatter JTAG
		+	* Sound Board with additional analog inputs and GPIOs
		+	* Your application specific interface board
		+
		+	The only limitation is your imagination!

	== [[Hammer_Board_Carrier\| Hammer Carrier Board]] ==		== [[Hammer_Board_Carrier\| Hammer Carrier Board]] ==

← Older revision		Revision as of 15:13, 4 August 2008
Line 1:		Line 1:
−	== Hammer Board ~~(the 40 pin DIP module)~~ ==	+	== Hammer Board ==

	=== Description ===		=== Description ===

@@ Line 15: / Line 15: @@
 [[Image:hammer3.jpg]]
-=== Hammer Board Pinouts ===
+=== Pinouts ===
 [[Image:Hammer-pinouts.jpg]]

@@ Line 7: / Line 7: @@
 The [[Hammer_Kit| Hammer Kit]] comes with everything you will need to begin developing for the Hammer Board, and is '''strongly recommended''' for first time Hammer Board users. All development tools have been created for use with Linux, so you will need a working Linux system to use the Hammer Board and develop applications for it.
-=== Hammer Board Photos ===
+=== Photos ===
 [[Image:hammer1.jpg]]

@@ Line 1: / Line 1: @@
 == Hammer Board (the 40 pin DIP module) ==
-=== Hammer Board Description ===
+=== Description ===
 The Hammer comes preloaded with an open source bootloader, Linux 2.6 kernel, and a uClibc/Busybox based root file system. Board schematics, application notes, and source code are also included on the CD. The Hammer Board is a 40 pin DIP modules that can run full standard GNU/Linux.