Difference between revisions of "Hammer How to Enc28j60"

From eLinux.org
Jump to: navigation, search
Line 8: Line 8:
 
Next we will be soldering it on to the [[Hammer_Carrier]]
 
Next we will be soldering it on to the [[Hammer_Carrier]]
  
We will use the 3.3V regulator of the Hammier Carrrier, but you already need to have
+
We will use the 3.3V regulator of the [[Hammier_Carrier]], but you already need to have
 
done the [[How_to_Swtching_5V_Regulator]]
 
done the [[How_to_Swtching_5V_Regulator]]
  
  
Wire the ENC28J60 th the hammer carrier pins as follows:
+
Wire the Olimex [[Enc28j60]] board to the [[Hammer_Carrier]] pins as follows:
 +
 
 +
{| border="1" cellspacing="0" cellpadding="5" align="center"
 +
! ENC28J60
 +
! Pin
 +
! Pin
 +
! Hammer
 +
|-
 +
|
 +
| 1
 +
| 7
 +
|
 +
|-
 +
|
 +
| 2
 +
| 6
 +
|
 +
|-
 +
|
 +
| 3
 +
| 5
 +
|
 +
|-
 +
|
 +
| 4
 +
| N/C
 +
|
 +
|-
 +
|
 +
| 5
 +
| 8
 +
|
 +
|-
 +
|
 +
| 6
 +
| N/C
 +
|
 +
|-
 +
|
 +
| 7
 +
| 11
 +
|
 +
|-
 +
|
 +
| 8
 +
| 9
 +
|
 +
|-
 +
|
 +
| 9
 +
| GND
 +
|
 +
|-
 +
|
 +
| 10
 +
| TP9
 +
|
 +
|-
 +
|}
  
 
enc -- hammer.  1 - 7, 2 - 6, 3 - 5, 4 - nc, 5 - 8, 6 - nc, 7 - 11, 8 - 9, 9 - gnd, 10 - tp9
 
enc -- hammer.  1 - 7, 2 - 6, 3 - 5, 4 - nc, 5 - 8, 6 - nc, 7 - 11, 8 - 9, 9 - gnd, 10 - tp9

Revision as of 07:08, 11 September 2007

First you have to get an Enc28j60, the following links may be usefull:

Next we will be soldering it on to the Hammer_Carrier

We will use the 3.3V regulator of the Hammier_Carrier, but you already need to have done the How_to_Swtching_5V_Regulator


Wire the Olimex Enc28j60 board to the Hammer_Carrier pins as follows:

ENC28J60 Pin Pin Hammer
1 7
2 6
3 5
4 N/C
5 8
6 N/C
7 11
8 9
9 GND
10 TP9

enc -- hammer. 1 - 7, 2 - 6, 3 - 5, 4 - nc, 5 - 8, 6 - nc, 7 - 11, 8 - 9, 9 - gnd, 10 - tp9

Also make sure that your 5V main power supply can supply the Hammer as well as the ENC28J60-H.

Enc28j60.jpg

Enc28j60 wireing.jpg

Software driver info:

The Good  Kernel SPI API
  The Bad  &
    The Ugly  The current "driver"