Difference between revisions of "Hammer How to Thumb Drive"

From eLinux.org
Jump to: navigation, search
m
(Added note about creating /dev/sdaX and copying fstab and inittab into root tree)
Line 22: Line 22:
  
 
  /opt            d      755    0      0      -      -      -      -      -
 
  /opt            d      755    0      0      -      -      -      -      -
 +
 +
You'll also need to ensure that /dev/sda, and /dev/sda1 exist in the '''device_table.txt'''. There are entries in there by default that look llke the following:
 +
 +
# SCSI Devices
 +
#/dev/sda b 640 0 0 8 0 0 0 -
 +
#/dev/sda b 640 0 0 8 1 1 1 15
 +
 +
You'll want to uncomment the two lines that start in /dev/sda. You'll probably also want to change the 15 at the end of the 2nd line to a more reasonable number like 4. Then it will only create /dev/sda1, /dev/sda2, /dev/sda3, and /dev/sda4.
 +
 +
# SCSI Devices
 +
/dev/sda b 640 0 0 8 0 0 0 -
 +
/dev/sda b 640 0 0 8 1 1 1 4
 +
  
 
Now it is time to add the Thumb Drive to your file system. When you build your rootfs, the /opt directory will be created for you with the permissions you set.
 
Now it is time to add the Thumb Drive to your file system. When you build your rootfs, the /opt directory will be created for you with the permissions you set.
Line 32: Line 45:
  
 
You can setup your Thumb drive for any mount point you want using this procedure. You can even mount your Thumb Drive as /usr.  
 
You can setup your Thumb drive for any mount point you want using this procedure. You can even mount your Thumb Drive as /usr.  
 +
 +
NOTE: In order for the changes that you made to '''/etc/inittab''' and '''/etc/fstab''' to take effect, you'll need to copy them into the '''project_build_arm/Hammer/root/etc''' directory.
 
    
 
    
 
[[Category:TCT-Hammer]]
 
[[Category:TCT-Hammer]]
 
[[Category:TinCanTools]]
 
[[Category:TinCanTools]]

Revision as of 14:38, 18 April 2008

You can add a USB Thumb Drive to your Hammer pretty easily. There are a few things you have to have in your kernel. Your Thumb Drive will be recognized as a SCSI device, probably /dev/sda1, if it is the only SCSI type device you have. When the usb-storage module loads, it will show which SCSI device you Thumb Drive is. Modular kernels are nice, and it is not difficult to be sure you have the right modules loaded. This how to is based on building everything possibe as modules.

You must have:

  • USB Core
  • USB Storage
  • SCSI, including SCSI disk and generic support.

configured in your kernel. Also be sure to activate the Kernel Automounter v4 and Automatic Kernel Module Loading so your Thumb Drive will be automatically mounted at bootup.

One way to get the USB Thumb Drive recognized and mounted is:

Add the necessary commands to the inittab file:

  • cd buildroot/target/device/Samsung/Hammer/target_skeleton/etc
  • edit the inittab.
  • Add these commands right below the jffs2 line:
 null::sysinit:/sbin/modprobe usb-storage
 null::sysinit:/bin/sleep 10

This will load the usb-storage module and wait for it to settle down.

Now you have to fix up the mount point where you want the Thumb Drive to appear. You can add a new mount point by editing the buildroot/target/device/Samsung/Hammer/device_table.txt file. If you want to mount your Thumb Drive at /opt (recommended for starters) then add the following line to device_table.txt:

/opt            d       755     0       0       -       -       -       -       -

You'll also need to ensure that /dev/sda, and /dev/sda1 exist in the device_table.txt. There are entries in there by default that look llke the following:

# SCSI Devices
#/dev/sda	b	640	0	0	8	0	0	0	-
#/dev/sda	b	640	0	0	8	1	1	1	15

You'll want to uncomment the two lines that start in /dev/sda. You'll probably also want to change the 15 at the end of the 2nd line to a more reasonable number like 4. Then it will only create /dev/sda1, /dev/sda2, /dev/sda3, and /dev/sda4.

# SCSI Devices
/dev/sda	b	640	0	0	8	0	0	0	-
/dev/sda	b	640	0	0	8	1	1	1	4


Now it is time to add the Thumb Drive to your file system. When you build your rootfs, the /opt directory will be created for you with the permissions you set.

Now edit buildroot/target/device/Samsung/Hammer/target_skeleton/etc/fstab file to add your mount point as follows:

/dev/sda1       /opt            ext2    defaults                0       0

This allows the Thumb Drive to be automatically setup and mounted for use.

You can setup your Thumb drive for any mount point you want using this procedure. You can even mount your Thumb Drive as /usr.

NOTE: In order for the changes that you made to /etc/inittab and /etc/fstab to take effect, you'll need to copy them into the project_build_arm/Hammer/root/etc directory.