Difference between revisions of "Hammer How to build Kernel"
(next step link)
|Line 12:||Line 12:|
8 MB =
8 MB =
You may have to increase the size of your '''initramfs/initrd''' to
You may have to increase the size of your '''initramfs/initrd''' to your ramdisk image if the '''uncompressed''' size is larger than about 12 MB. There will be both compressed and uncompressed rootfs images in the buildroot/binaries/<project> directory. To do this, you have to set the size of the '''initramfs/initrd''' in the kernel. Find Block Devices in the kernel configuration and set the size to be just a little larger than your '''uncompressed''' initramfs/initrd. Only add a multiple of 1024 bytes.
Latest revision as of 20:32, 11 April 2011
Here is how to build a custom kernel: NOTE: Kernel 2.6.29 seemed a little easier to build then 2.6.22 did, Check towards bottom for instructions. NOTE: If you are installing a custom rootfs, you may have to increase the size of the space in flash to hold the new rootfs image. You do this by editing the linux-<version>/arch/arm/mach-s3c2410/mach-tct_hammer.c file. Find the .size string and change the value to be a little larger than your rootfs image is. The image size is in hex, so you will have to do a conversion to get the right value.
Some common values for .size are:
2 MB = 0x340000 3 MB = 4 MB = 5 MB = 6 MB = 8 MB =
You may have to increase the size of your initramfs/initrd to accommodate your ramdisk image if the uncompressed size is larger than about 12 MB. There will be both compressed and uncompressed rootfs images in the buildroot/binaries/<project> directory. To do this, you have to set the size of the initramfs/initrd in the kernel. Find Block Devices in the kernel configuration and set the size to be just a little larger than your uncompressed initramfs/initrd. Only add a multiple of 1024 bytes.
tar xzf linux-2.6.22.tar.gz cd linux-2.6.22 zcat ../Hammer-linux-2.6.22-09122007.diff.gz | patch -p1 Edit linux-<version>/arch/arm/mach-s3c2410/mach-tct_hammer.c to change .size if needed. cp hammer-config .config make oldconfig make zImage make modules
The kernel can be found in arch/arm/boot/zImage
If your kernel and rootfs compress size is bigger than 1Mo, you will need to change some Apex config.
If you want to flash the bootloader, do
make menuconfig In Environment Regions (nor:1280k+2048k) Source region for ramdisk image to have a rootfs image smaller than 2048k
and then reflash with the new apex.bin file
newer kernel (2.6.22 to 2.6.29)
If you want to compile a kernel upper than 2.6.22, you don't need to patch the kernel. To make a new kernel, just :
export ARCH=arm export CROSS_COMPILE=arm-linux-uclibc- make tct_hammer_defconfig make menuconfig In Device drivers -> Character devices -> Serial drivers Type Y for Samsung SoC serial support In Device drivers Type 'Y' for: GPIO support, SPI support, and SD Support. make zImage export INSTALL_MOD_PATH=../../buildroot/project_build_arm/Hammer/root/ ==> depend on your kernel source directory location make modules_install
If you don't want to type export ARCH=arm and CROSS_COMPILE=arm-linux-uclibc- every time you make a fresh zImage you could edit the kernel top-level Makefile. Goto ../../buildroot/build_arm/linux-2.6.29.x/Makefile, somewhere on line 193 and 194 you will see:
ARCH ?= $(SUBARCH) CROSS_COMPILE ?= arm-linux-
Change it to:
ARCH := arm CROSS_COMPILE := arm-linux-uclibc-