Difference between revisions of "HawkboardFAQ"

From eLinux.org
Jump to: navigation, search
(U-Boot)
Line 10: Line 10:
  
 
'''A''': Due to color space issues it is a little bit tricky at the moment. Not much software supports it out of the box. You can find test procedure [[Testing Video Input of Hawkboard | here]]
 
'''A''': Due to color space issues it is a little bit tricky at the moment. Not much software supports it out of the box. You can find test procedure [[Testing Video Input of Hawkboard | here]]
 +
 +
==Kernel/uImage==
 +
 +
'''Q''':How to see Kernel Message for debugging Purpose?
 +
 +
'''A''':You can use earlyprintk=vga", "earlyprintk=ttyS0" in bootargs,you will also need to enable that
 +
in kernel by enabling CONFIG_EARLY_PRINTK
 +
  
 
==U-Boot==
 
==U-Boot==

Revision as of 14:27, 23 May 2010


Camera Interface

Q: How can I use/test camera interface of Hawkboard?

A: Due to color space issues it is a little bit tricky at the moment. Not much software supports it out of the box. You can find test procedure here

Kernel/uImage

Q:How to see Kernel Message for debugging Purpose?

A:You can use earlyprintk=vga", "earlyprintk=ttyS0" in bootargs,you will also need to enable that in kernel by enabling CONFIG_EARLY_PRINTK


U-Boot

Q:I am not getting U-BOOT Prompt/How do i recovery U-Boot ?

A:Please see recovery guide to Reflash uboot on Hawkboard Here


Q:How to Do i autoboot Hawkboard with my RootFS on USB Drive.?

A:To Autoboot hawkboard kernel must reside on NAND & follow these

 setenv serverip 192.168.0.100
 setenv ipaddr 192.168.0.150 
 tftpboot 0xc0700000 u-boot_nand_ais_v1.bin
 nand erase
 nand write.e 0xc0700000 0x20000 0x70000
 tftp c0700000 uImage
 nand write.e 0xc0700000 0x200000 0x200000
 setenv bootargs console=ttyS2,115200n8 console=tty1 noinitrd root=/dev/sda rootwait rw init=/sbin/init
 setenv bootcmd "setenv console=ttyS2,115200n8 console=tty1 noinitrd root=/dev/sda1 rootwait rw init=/sbin/init;nand read.e 0xc0700000 0x200000 0x200000;bootm 0xc0700000"
 saveenv


Q:How Do i flash NAND with U-Boot without using TI's Host Utility or any Linux Application exists?

A:You will need Mono package (DOT NET implementation for Linux) & dvflashutils .Check below for more details http://processors.wiki.ti.com/index.php?title=Serial_Boot_and_Flash_Loading_Utility


Q:Is there alternative to Load uImage beside TFTP or Flashing to NAND

A:Yes there two more methods you could do

  1. Transfer uImage through NFS using:
 hawkboard.org > nfs 0xc0700000 192.168.0.100:/nfsroot/uImage
 hawkboard.org > setenv bootargs ....
 hawkboard.org > bootm c0700000
  1. Transferring uImage through Serial Interface using Ymodem protocol

Check this thread http://groups.google.com/group/hawkboard/browse_thread/thread/ecc57e1b964bc2c4/b0e1ad260a226bd1?lnk=gst&q=ymodem

Ubuntu Rootfs

Q:How to Do i installed new packages in ubuntu jaunty rootfs?

A:If you have made the rootfs using rootstock with "apt" as one of Seed paramter than you can use "apt-get install <package_name> to install required package.


Booting Errors

Q:I am getting "Kernel panic - not syncing: VFS: Unable to mount root fs ..." error how to resolve this?

A:Kernel panic occurs when kernel is not able to find rootfs(init program ),either the bootargs is not correct or source of rootfs is not available.

DSP

Q:How do i start with DSP Programming on Hawkboard?

A:Read Thread

  1. http://groups.google.com/group/hawkboard/browse_thread/thread/3534c1590940688c/f7118c18635d8275
  2. http://groups.google.com/group/hawkboard/browse_thread/thread/661c1ce0f342b1f8/d4d617831983b78d

Hawkboard

Q:Does Hawkboard support SDHC Card?

A:Yes ,it supports SD & SDHC Card.