Difference between revisions of "LeapFrog Pollux Platform: Networking"

From eLinux.org
Jump to: navigation, search
(Hardware Needed)
(Undo revision 57043 by Jrspruitt (talk))
Line 7: Line 7:
  
 
== Hardware Needed ==
 
== Hardware Needed ==
[[LeapFrog_Pollux_Platform:_Cartridge| Cartridge]]
+
[[LeapFrog_Pollux_Platform:_Console_Access| Console Access]]
 +
 
  
 
== Configure Device ==
 
== Configure Device ==

Revision as of 02:19, 14 July 2011

Summary

This tutorial shows the basics steps to configur a network connection between a host PC and your LeapFrog Pollux Platform device. The LeapPad_Explorer and Leapster_Explorer both come with everything you need for networking, minus a few configuration steps, while the Didj requires a more involved process Enable Didj Networking.

Prerequisites

For the Didj you'll need to Enable Networking


Hardware Needed

Console Access


Configure Device

Temporary Device Setup

This is the easiest way to get networking up and working quickly. But all configuration will be lost once the device is rebooted or turned off.

Set the devices IP address. On Device

ifconfig usb0 10.0.0.2 netmask 255.255.255.0

Once the host is also configured you can test connectivity by running..

ping 10.0.0.1

You should see ping return the packet times.


Static IP on Avahi Systems

For the Leapster Explorer and LeapPad Explorer you may want to disable the random IP. They use a DHCP type system called Avahi. This will force it to a static IP address, which will make it much easier if you use networking on your device a lot.

You can start the explorer and have it default to a static IP address by simply holding down the brightness button at boot time. Simply edit /etc/init.d/networking, look for any place there is an IP address and replace it with yours, you should also change the bit after the slash to set your netmask), edit lines 32 and 41:

ifconfig usb0 192.168.0.111/24


and make them look like this:

ifconfig usb0 10.0.0.2 netmask 255.255.255.0


Now plug in a mini usb cable and Reboot and as soon as you see: Emerald Base: Starting /etc/init.d/networking ... Emerald Base: /etc/init.d/networking: Holding brightness: forcing static IP

on the console then it is safe to let go.

You can make this permanent so that you don't have to hold down brightness by removing the avahi flag:

 rm /flags/avahi

now reboot and you will get your static IP address assigned


Configure Host

For the host PC you'll need to know which interface it is using, after connecting and turning on your device, you can run dmesg, it should be something like usb0, eth1, eth2, etc. This will depend on your particular host PC's netorking set up, in this example I use usb0.


Temporary Host Setup

Like the temporary device set up, once it is rebooted, turned off, or unplugged, you will loose your settings.

On Host

ifconfig 10.0.0.1 netmask 255.255.255.0

Once the device is also configured you can test connectivity by running.

ping 10.0.0.2

You should see ping return the packet times.

Once this is done you need to configure the host:

Using Local-link

I'm using ubuntu 10.04, it has a automatic configuration, I've set mine so that auto usb0 has the ipv4, method setting of 'local-link only' and in auto eth2 I have hardcoded the ip address to 10.0.0.1, netmask 255.255.255.0, gateway of 0.0.0.0


Route or Bridging Configuration

The Internet Access tutorial also provides some methods of permanent host configuration. If you don't need access to the internet, you can leave out configuring the nameservers.