Difference between revisions of "Minnowboard:MaxLures"

From eLinux.org
Jump to: navigation, search
(Retried)
(Jetsam Lure: - moving some info that was on the main page to the lure page)
Line 72: Line 72:
 
**[[media:Jetsam-Lure_X1_ccBYNC_Schematic.pdf|Schematic (PDF)]]
 
**[[media:Jetsam-Lure_X1_ccBYNC_Schematic.pdf|Schematic (PDF)]]
 
  |}
 
  |}
 +
 +
'''Note:''' PCIe expansion cards can be added via the Jetsam lure:
 +
* By itself, Jetsam allows both half and full-height mPCIe cards
 +
* Full desktop-style x1 PCIe cards can be added via a mPCIe-PCIe adapter such as those available from:
 +
** [http://amfeltec.com/adapters/ Amfeltec] (e.g. [http://amfeltec.com/products/flexible-minipci-express-to-pci-express-adapter/ Flexible MiniPCI Express to PCI Express Adapter]).
 +
* Although the electrical interface only supports x1, cards with up to x16 physical connections may be installed via an adapter such as those made by:
 +
** [http://www.startech.com/Cards-Adapters/Slot-Extension/ StarTech] (e.g. [http://www.startech.com/Cards-Adapters/Slot-Extension/PCI-Express-X1-to-X16-Low-Profile-Slot-Extension-Adapter~PEX1TO162 PCI Express X1 to X16 Low Profile Slot Extension Adapter]).
  
 
== Flotsam Lure ==
 
== Flotsam Lure ==

Revision as of 17:03, 16 March 2015

Minnowboard Max Lure Information

Lures In production (currently available)

These are lures that are currently available, and obtainable in a pre-built state.

Calamari Lure

Break out board intended mainly for testing gpio and low speed interfaces, as


  • Features:
    • SPI Based ADC
    • 10K Slider POT
    • RGB LED
    • 2 PWM LEDS
    • 2 TTL UART Headers
    • 7-Segment Display with 595 shift register
    • I2C EEPROM
    • 3 Buttons
  • Produced by: CircuitCo
  • Additional Information: none available right now


CalamariLure-SlantedTop01-650.jpg

Jetsam Lure

mPCI-E break out board


  • Features:
    • Single mPCIe Slot
  • Produced by: CircuitCo
  • Additional Information: none available right now


Jetsam-lure-a.jpg

Note: PCIe expansion cards can be added via the Jetsam lure:

Flotsam Lure

mSATA break out board


  • Features:
    • single mSATA Slot
  • Produced by: CircuitCo
  • Additional Information: none available right now


Flotsam-lure-a.jpg


Prototype Lure

Generic Prototype Area on 0.1" grids


  • Features:
    • Generic Prototype Area on 0.1" grids
  • Produced by: CircuitCo
  • Additional Information: none available right now


Prototype-lure-b.jpg ProtoLure-SlantedSide01-650.jpg

IDP JTAG Lure

Intel IDP JTAG lure


  • Features:
    • Adapter for Intel IDP JTAG
  • Produced by: CircuitCo
  • Additional Information: none available right now


Jtaglure-slanted.jpg

Ready to Build

These are lures that are functionally complete, but are not being (or not currently) in production and/or available to buy. To be in this state the lures need to be in a state where an individual has enough information to fully build these on their own.

Cuttle(bone) Lure

Adapter from Low Speed Connector I/O (I2C,I2S,UARTs,SPI,GPIO) to BeagleBone * Capes. Works with a variety of Capes but not all.


  • Features:
    • low speed adapter for MAX to BeagleBone capes
  • Produced by: Tom King
  • Additional Information: none available right now
Cuttle lure.png

Planned Lures

These are lures that are either in the planning or early design stages and are not ready for production.

Retried

These are lures that do not have build files available, but information pertaining to them is still pertinent.

Ika Lure

The Ika lure takes the existing low speed I/O and expands it (through I2C chips) to allow for an Arduino compatible shield to be used with the MinnowBoard MAX.
  • Features:
    • Electrically Arduino Compatible
    • 3.3v & 5.5v tolerant (flipped via jumpers)
MinnowMax - Lure - Ika.png
Ika-lure-a.jpg

Note: Board was cancelled, though some boards were made available at various conferences as give aways.