Pixter Expansion Slot - Revision history

Wmat: Fixing broken links.

2010-01-28T00:19:58Z

Fixing broken links.

Chris at 12:50, 14 July 2007

2007-07-14T12:50:12Z

Wmat: Legacy Content Conversion

2007-03-01T03:29:42Z

Legacy Content Conversion

New page

The Pixter expansion slot is a 60 pin double sided card edge connector. the pads are .035" wide, with a .015" gap between pads, and a total of .050" center-to-center of the pads. the pcb is .047" thick which is a somewhat non-standard thickness. most pcb board houses with manufactor either .031 or .062 for their express and reduced cost production. there are a few production houses that will do the .047 for no additional cost, but only do them on a specific day of the week. Pin 60 is tied to the control(on/off) line of the S-1131 ( [[Media:PixterChipList/S1131.pdf]] ) voltage regulator which allows the external cart to power the unit on and off. By using a [[Pixter Dev Cart]], all the following pins can be used to develop projects:

{|
|-
| 1
| A0
| 2
| D0
|-
| 3
| A1
| 4
| D1
|-
| 5
| A2
| 6
| D2
|-
| 7
| A3
| 8
| D3
|-
| 9
| A4
| 10
| D4
|-
| 11
| A5
| 12
| D5
|-
| 13
| A6
| 14
| D6
|-
| 15
| A7
| 16
| D7
|-
| 17
| A8
| 18
| D8
|-
| 19
| A9
| 20
| D9
|-
| 21
| A10
| 22
| D10
|-
| 23
| A11
| 24
| D11
|-
| 25
| A12
| 26
| D12
|-
| 27
| A13
| 28
| D13
|-
| 29
| A14
| 30
| D14
|-
| 31
| A15
| 32
| D15
|-
| 33
| A16
| 34
| PE1/UARTTX2
|-
| 35
| A17
| 36
| PE0/UARTRX2
|-
| 37
| A18
| 38
| nCS2
|-
| 39
| A19
| 40
| nCS3
|-
| 41
| A20
| 42
| nOE
|-
| 43
| A21
| 44
| nWE
|-
| 45
| A22
| 46
| Vdd
|-
| 47
| A23
| 48
| PE4/SSPTX
|-
| 49
| PD2/INT2
| 50
| PE3/UARTTX0
|-
| 51
| PD4/INT4/UARTRX1
| 52
| PF6
|-
| 53
| PD3/INT3/UARTTX1
| 54
| PF4
|-
| 55
| PD5/INT5/DACK
| 56
| Vss
|-
| 57
| PD6/INT6/DREQ
| 58
| Vdd
|-
| 59
| Vss
| 60
| power control
|}

<hr />
[[Category Pixter]]

← Older revision		Revision as of 00:19, 28 January 2010
Line 1:		Line 1:
−	The Pixter expansion slot is a 60 pin double sided card edge connector. the pads are .035" wide, with a .015" gap between pads, and a total of .050" center-to-center of the pads. the pcb is .047" thick which is a somewhat non-standard thickness. most pcb board houses with manufactor either .031 or .062 for their express and reduced cost production. there are a few production houses that will do the .047 for no additional cost, but only do them on a specific day of the week. Pin 60 is tied to the control(on/off) line of the S-1131 ( [[Media:~~PixterChipList/~~S1131.pdf]] ) voltage regulator which allows the external cart to power the unit on and off. By using a [[Pixter Dev Cart]], all the following pins can be used to develop projects:	+	The Pixter expansion slot is a 60 pin double sided card edge connector. the pads are .035" wide, with a .015" gap between pads, and a total of .050" center-to-center of the pads. the pcb is .047" thick which is a somewhat non-standard thickness. most pcb board houses with manufactor either .031 or .062 for their express and reduced cost production. there are a few production houses that will do the .047 for no additional cost, but only do them on a specific day of the week. Pin 60 is tied to the control(on/off) line of the S-1131 ( [[Media:S1131.pdf]] ) voltage regulator which allows the external cart to power the unit on and off. By using a [[Pixter Dev Cart]], all the following pins can be used to develop projects:

← Older revision		Revision as of 12:50, 14 July 2007
Line 156:		Line 156:

	<hr />		<hr />
−	[[Category Pixter]]	+
		+	[[Category:Pixter]]