Difference between revisions of "R-Pi PXE Server"

From eLinux.org
Jump to: navigation, search
m
m (Overview of this project)
Line 38: Line 38:
 
#Deploy to a live network
 
#Deploy to a live network
  
1. General Preparation
+
==General Preparation==
  
 
First, you need to install all of the necessary software.
 
First, you need to install all of the necessary software.
Line 61: Line 61:
 
1C) Disconnect the Raspberry Pi from the network.
 
1C) Disconnect the Raspberry Pi from the network.
  
2. Configuring the DHCP server on the RPi
+
==Configuring the DHCP server on the RPi==
  
 
Now you need to setup the DHCP server.
 
Now you need to setup the DHCP server.
Line 67: Line 67:
 
2A alt 1) Create /etc/dhcpd.conf with the following contents:
 
2A alt 1) Create /etc/dhcpd.conf with the following contents:
  
ddns-update-style interim;
+
ddns-update-style interim;
subnet 192.168.0.0 netmask 255.255.255.0 {
+
subnet 192.168.0.0 netmask 255.255.255.0
range 192.168.0.10 192.168.0.254;
+
{
default-lease-time 3600;
+
  range 192.168.0.10 192.168.0.254;
max-lease-time 4800;
+
  default-lease-time 3600;
option routers 192.168.0.1;
+
  max-lease-time 4800;
option domain-name-servers 192.168.0.1;
+
  option routers 192.168.0.1;
option subnet-mask 255.255.255.0;
+
  option domain-name-servers 192.168.0.1;
option domain-name "llama.net";
+
  option subnet-mask 255.255.255.0;
option time-offset -8;
+
  option domain-name "llama.net";
}
+
  option time-offset -8;
 +
}
  
host llama0 {
+
host llama0
hardware ethernet 04:4B:80:80:80:03;
+
{
fixed-address 192.168.0.254;
+
  hardware ethernet 04:4B:80:80:80:03;
option host-name "llama0";
+
  fixed-address 192.168.0.254;
filename "pxelinux.0";
+
  option host-name "llama0";
}
+
  filename "pxelinux.0";
 +
}
  
 
To explain – the above configuration file sets up a DHCP server that will assign IP address 192.168.0.254 to your client box that has MAC address 04:4B:80:80:80:03 assigned to its PXE-boot capable NIC. Another thing to note is that we're reserving the private 192.168 subnet for this setup. The only thing you need to change in the above, is the MAC address to match that of the NIC on your client box.
 
To explain – the above configuration file sets up a DHCP server that will assign IP address 192.168.0.254 to your client box that has MAC address 04:4B:80:80:80:03 assigned to its PXE-boot capable NIC. Another thing to note is that we're reserving the private 192.168 subnet for this setup. The only thing you need to change in the above, is the MAC address to match that of the NIC on your client box.
Line 116: Line 118:
 
service dhcpd start
 
service dhcpd start
  
3. Configuring the tftp server on the RPi
+
==Configuring the tftp server on the RPi==
  
 
Next you need to activate tftp within xinetd.
 
Next you need to activate tftp within xinetd.
Line 125: Line 127:
  
 
Command:
 
Command:
service xinetd restart
+
service xinetd restart
  
 
3C) Now we need to setup your PXE server to use a static IP on the new private subnet. Create the file /etc/sysconfig/network-scripts/ifcfg-eth0.static with the following contents:
 
3C) Now we need to setup your PXE server to use a static IP on the new private subnet. Create the file /etc/sysconfig/network-scripts/ifcfg-eth0.static with the following contents:
  
DEVICE=eth0
+
DEVICE=eth0
BOOTPROTO=STATIC
+
BOOTPROTO=STATIC
ONBOOT=no
+
ONBOOT=no
TYPE=Ethernet
+
TYPE=Ethernet
IPADDR=192.168.0.2
+
IPADDR=192.168.0.2
NETMASK=255.255.255.0
+
NETMASK=255.255.255.0
GATEWAY=192.168.0.1
+
GATEWAY=192.168.0.1
  
 
3D) Now we need to setup the PXE boot environment on the server. To do this, you need to have either the Linux distribution that you wish to install over PXE either in CD format, or all the content of the CDs available on the network.
 
3D) Now we need to setup the PXE boot environment on the server. To do this, you need to have either the Linux distribution that you wish to install over PXE either in CD format, or all the content of the CDs available on the network.
Line 145: Line 147:
 
3E) Next we need to configure pxelinux. First create the directory /tftpboot/pxelinux.cfg (and make it world readable). Inside that directory you need to create a number of zero size files (use touch):
 
3E) Next we need to configure pxelinux. First create the directory /tftpboot/pxelinux.cfg (and make it world readable). Inside that directory you need to create a number of zero size files (use touch):
  
touch /tftpboot/pxelinux.cfg/C
+
touch /tftpboot/pxelinux.cfg/C
touch /tftpboot/pxelinux.cfg/C0
+
touch /tftpboot/pxelinux.cfg/C0
touch /tftpboot/pxelinux.cfg/C0A
+
touch /tftpboot/pxelinux.cfg/C0A
touch /tftpboot/pxelinux.cfg/C0A8
+
touch /tftpboot/pxelinux.cfg/C0A8
touch /tftpboot/pxelinux.cfg/C0A80
+
touch /tftpboot/pxelinux.cfg/C0A80
touch /tftpboot/pxelinux.cfg/C0A800
+
touch /tftpboot/pxelinux.cfg/C0A800
touch /tftpboot/pxelinux.cfg/C0A800F
+
touch /tftpboot/pxelinux.cfg/C0A800F
touch /tftpboot/pxelinux.cfg/C0A800FE
+
touch /tftpboot/pxelinux.cfg/C0A800FE
touch /tftpboot/pxelinux.cfg/01-04-4B-80-80-80-03 #Edit to match your PC
+
touch /tftpboot/pxelinux.cfg/01-04-4B-80-80-80-03 #Edit to match your PC
  
 
The first 8 are the hex representation of the 192.168.0.254 IP address that your PXE boot client will be assigned. The permutations allow a broader IP subnet to be searched first for matches. The last entry is the MAC address of your PXE boot client's NIC (with dashes substituted for the colons), with '01' pre-pended. The "01" at the front represents a hardware type of Ethernet, so pxelinux.0 see's the configuration string as an IP address.
 
The first 8 are the hex representation of the 192.168.0.254 IP address that your PXE boot client will be assigned. The permutations allow a broader IP subnet to be searched first for matches. The last entry is the MAC address of your PXE boot client's NIC (with dashes substituted for the colons), with '01' pre-pended. The "01" at the front represents a hardware type of Ethernet, so pxelinux.0 see's the configuration string as an IP address.
Line 159: Line 161:
 
3F) Now create the default pxelinux configuration inside the new file /tftpboot/pxelinux.cfg/default:
 
3F) Now create the default pxelinux configuration inside the new file /tftpboot/pxelinux.cfg/default:
  
prompt 1
+
prompt 1
default linux
+
default linux
timeout 100
+
timeout 100
  
label linux
+
label linux
kernel vmlinuz
+
kernel vmlinuz
append initrd=initrd.img ramdisk_size=9216 noapic acpi=off
+
append initrd=initrd.img ramdisk_size=9216 noapic acpi=off
  
  
4. Configuring the web server on the RPi
+
==Configuring the web server on the RPi==
  
 
4A) Now you need to put the full contents of your Linux distro (all CDs) somewhere on disk. I put it under /tftpboot/RHEL4U1. In order to allow for installation over HTTP (apache), edit/etc/httpd/conf/httpd.conf and add the following:
 
4A) Now you need to put the full contents of your Linux distro (all CDs) somewhere on disk. I put it under /tftpboot/RHEL4U1. In order to allow for installation over HTTP (apache), edit/etc/httpd/conf/httpd.conf and add the following:
  
<Directory /tftpboot/RHEL4U1>
+
<Directory /tftpboot/RHEL4U1>
Options Indexes
+
Options Indexes
AllowOverride None
+
AllowOverride None
</Directory>
+
</Directory>
Alias /linux /tftpboot/RHEL4U1
+
Alias /linux /tftpboot/RHEL4U1
  
 
4B) Start web server
 
4B) Start web server
  
 
Command:
 
Command:
service httpd start
+
service httpd start
  
5. Test with a single PC
+
==Test with a single PC==
  
 
5A) At this stage, you're ready to hook up the switch. You should have CAT5 running between the switch & the PXE boot server, and the client box.
 
5A) At this stage, you're ready to hook up the switch. You should have CAT5 running between the switch & the PXE boot server, and the client box.
Line 197: Line 199:
  
 
   
 
   
Extra text from http://www.debian-administration.org/articles/478
+
=Extra useful text=
 +
From http://www.debian-administration.org/articles/478
  
 
If you're looking to perform a lot of system recovery, or system installation, then network booting with PXE is ideal. PXE allows you to boot up a system and have it automatically get an IP address via DHCP and start booting a kernel over the network.
 
If you're looking to perform a lot of system recovery, or system installation, then network booting with PXE is ideal. PXE allows you to boot up a system and have it automatically get an IP address via DHCP and start booting a kernel over the network.

Revision as of 18:22, 7 February 2012

Classroom boot server

This is very preliminary, do not try to follow these instructions.

I just happen to need a PXE server at the moment, so I am documenting all of the necessary steps.

As yet, I have not decided on Fedora or Debian, so the instructions are a bit of a mix at the moment.



What does it do?

This server allows your to use cheap PCs in a classroom/library/café which do not have their own hard disks. When the PCs are turned on, they will fetch the boot information from a PXE/netboot server. The major advantage is that the cost of each PC is reduced because individual hard disks are not needed. Also, there is no information stored locally on each PC for the user to tamper with. If the user messes up a PC, just reboot the PC to return to normal.

What do you need?

  • A Raspberry Pi, model B.
  • A boot SD card for the Raspberry Pi. [What size? Needs to hold ISO image]
  • An Ethernet cable to connect to the local network.

How does it work?

PXE (Preboot eXecution Environment) is a method to allow a PC without a hard disk to boot from the network. It is also known as net booting or LAN13 booting.

If a PC is configured to boot over the network, it will search the local network for a DHCP (Dynamic Host Configuration Protocol) server. The DHCP server will assign an IP address to the PC and tell the PC the address of a tftp (trivial file transport protocol) server where a boot image is available.

The PC connects to the tftp server and downloads the basic boot image. This boot image will then instruct the PC to fetch the complete operating system from a web server.

The Raspberry Pi will act as the DCHP server, the tftp server, and the web server.

Overview of this project

  1. General Preparation
  2. Configuring the DHCP server on the RPi
  3. Configuring the tftp server on the RPi
  4. Configuring the web server on the RPi
  5. Test with a single PC
  6. Deploy to a live network

General Preparation

First, you need to install all of the necessary software.

1A) Connect your Raspberry Pi to a network. Check that you have an internet connection

Command:

ping www.google.com

1B) Install the following packages [To be checked: these ship with Fedora Core 4 already, so they may be part of the default RPi installation]

  • tftp-server
  • dhcp
  • httpd
  • syslinux

Command:

yum install tftp-server dhcp httpd syslinux

answer Y to all dependency/installation questions.

1C) Disconnect the Raspberry Pi from the network.

Configuring the DHCP server on the RPi

Now you need to setup the DHCP server.

2A alt 1) Create /etc/dhcpd.conf with the following contents:

ddns-update-style interim;
subnet 192.168.0.0 netmask 255.255.255.0
{
 range 192.168.0.10 192.168.0.254;
 default-lease-time 3600;
 max-lease-time 4800;
 option routers 192.168.0.1;
 option domain-name-servers 192.168.0.1;
 option subnet-mask 255.255.255.0;
 option domain-name "llama.net";
 option time-offset -8;
}
host llama0
{
 hardware ethernet 04:4B:80:80:80:03;
 fixed-address 192.168.0.254;
 option host-name "llama0";
 filename "pxelinux.0";
}

To explain – the above configuration file sets up a DHCP server that will assign IP address 192.168.0.254 to your client box that has MAC address 04:4B:80:80:80:03 assigned to its PXE-boot capable NIC. Another thing to note is that we're reserving the private 192.168 subnet for this setup. The only thing you need to change in the above, is the MAC address to match that of the NIC on your client box. This configuration says that the client PC should be informed that the file “pxelinux.0” is available.

Question – Why are we using a static IP assignment?

2A alt 2) Create /etc/dhcpd.conf with the following contents:

option domain-name-servers 192.168.0.1; default-lease-time 3600; max-lease-time 4800; authoritative;

subnet 192.168.0.0 netmask 255.255.255.0 {

       range 192.168.0.70 192.168.1.100;
       filename "pxelinux.0";
       next-server 192.168.0.50;
       option subnet-mask 255.255.255.0;
       option broadcast-address 192.168.0.255;
       option routers 192.168.0.1;

}

Here we've configured the server to give out IP addresses from the range 192.168.0.70-100, set the default gateway to be 192.168.0.1

We've also used next-server to point to the TFTP server we're using (which is the same host as our DHCP server, but doesn't need to be). We've chosen the default name of pxelinux.0 as the name of the file for booting clients to request.

2B) Now start dhcpd

Command: service dhcpd start

Configuring the tftp server on the RPi

Next you need to activate tftp within xinetd.

3A) Edit the file /etc/xinetd.d/tftp to change disable=yes to disable=no

3B) Then restart xinetd.

Command:

service xinetd restart

3C) Now we need to setup your PXE server to use a static IP on the new private subnet. Create the file /etc/sysconfig/network-scripts/ifcfg-eth0.static with the following contents:

DEVICE=eth0
BOOTPROTO=STATIC
ONBOOT=no
TYPE=Ethernet
IPADDR=192.168.0.2
NETMASK=255.255.255.0
GATEWAY=192.168.0.1

3D) Now we need to setup the PXE boot environment on the server. To do this, you need to have either the Linux distribution that you wish to install over PXE either in CD format, or all the content of the CDs available on the network.

On the first CD of every RH/FC distribution there is a subdirectory called 'isolinux'. In that directory you will find two files, vmlinuz and initrd.img. These are the kernel & initrd.img that the RH/FC bootable CDs use to get the installer (anaconda) booted for performing the installation. Copy both of those files into /tftpboot and make sure that they are world readable. If you are planning to allow more than one version/distribution to be PXE boot installable, then you should rename both files so that its clear that they are for whatever version/distribution they came from (such as vmlinuz-RHEL4, initrd-RHEL4).

Next, you need the actual pxe boot linux kernel (what is actually run immediately after your PXE boot client box gets a DHCP lease). In this case, that file is pxelinux.0, and is part of the syslinux RPM. For FC4, you can find it at /usr/lib/syslinux/pxelinux.0. Copy that file into /tftpboot and make sure that it is world readable.

3E) Next we need to configure pxelinux. First create the directory /tftpboot/pxelinux.cfg (and make it world readable). Inside that directory you need to create a number of zero size files (use touch):

touch /tftpboot/pxelinux.cfg/C
touch /tftpboot/pxelinux.cfg/C0
touch /tftpboot/pxelinux.cfg/C0A
touch /tftpboot/pxelinux.cfg/C0A8
touch /tftpboot/pxelinux.cfg/C0A80
touch /tftpboot/pxelinux.cfg/C0A800
touch /tftpboot/pxelinux.cfg/C0A800F
touch /tftpboot/pxelinux.cfg/C0A800FE
touch /tftpboot/pxelinux.cfg/01-04-4B-80-80-80-03 #Edit to match your PC

The first 8 are the hex representation of the 192.168.0.254 IP address that your PXE boot client will be assigned. The permutations allow a broader IP subnet to be searched first for matches. The last entry is the MAC address of your PXE boot client's NIC (with dashes substituted for the colons), with '01' pre-pended. The "01" at the front represents a hardware type of Ethernet, so pxelinux.0 see's the configuration string as an IP address.

3F) Now create the default pxelinux configuration inside the new file /tftpboot/pxelinux.cfg/default:

prompt 1
default linux
timeout 100
label linux
kernel vmlinuz
append initrd=initrd.img ramdisk_size=9216 noapic acpi=off


Configuring the web server on the RPi

4A) Now you need to put the full contents of your Linux distro (all CDs) somewhere on disk. I put it under /tftpboot/RHEL4U1. In order to allow for installation over HTTP (apache), edit/etc/httpd/conf/httpd.conf and add the following:

<Directory /tftpboot/RHEL4U1>
Options Indexes
AllowOverride None
</Directory>
Alias /linux /tftpboot/RHEL4U1

4B) Start web server

Command:

service httpd start

Test with a single PC

5A) At this stage, you're ready to hook up the switch. You should have CAT5 running between the switch & the PXE boot server, and the client box.

5B) On the PXE boot server, bring down your DHCP network connected eth0 (ifdown eth0), disconnect the CAT5 connected to the network, and plug in the cat5 connected to your private switch. Now bring up the static IP for the PXE server with (ifup eth0.static). You can verify that it came up successfully by verifying that you have IP address 192.168.0.2 in ifconfig.

5C) Plug the PXE client box's CAT5 into the switch, and verify that the NIC appears first in the BIOS boot order. (re)boot and you should get a DHCP lease, and start booting successfully off the network.

5D) When you get into the RH/FC installer which asks you for the install method, choose HTTP. Fill in 192.168.0.2 for the name, and 'linux' for the path, and you should be all set.

5E) If you run into any problems, check /var/log/messages for errors (that's where all dhcp & tftp stuff will get logged). /var/log/httpd is where apache logs, but if you get that far, your problem is an apache configuration/setup issue, and not a PXE boot issue.


Extra useful text

From http://www.debian-administration.org/articles/478

If you're looking to perform a lot of system recovery, or system installation, then network booting with PXE is ideal. PXE allows you to boot up a system and have it automatically get an IP address via DHCP and start booting a kernel over the network. PXE itself stands for "Pre-boot eXecution Environment", which describes how it works in the sense that the clients using it haven't booted in a traditional manner. In order to use PXE you need to setup a boot-server which will allow client systems to : • Request an IP address (via DHCP) • Download a kernel (via TFTP) With both of these services in place any system which supports PXE/network-booting (you might need to enable it in the BIOS) should be able to gain an IP address, fetch a kernel, and boot without an installed operating system. (This is ideal for systems which can't be booted by a traditional approach; for example your new AMD-64 system which doesn't have a CD/DVD drive!) Our Setup For the purposes of this article we'll assume: • We're working with a small network 192.168.1.0/24 • We'll allow all local machines to boot and get an IP address via DHCP from the range 196.168.1.70-192.168.1.100 • Our "boot-server" is the host "itchy" with IP address 192.168.1.50 • We will serve the same kernel to each host. In our example we'll configure a PXE-server which will allow remote systems to run the Debian Etch installer, but nothing here is specific to that. PXE allows you to configure a system to boot from an arbitrary kernel (and matching ramdisk if you wish to use one). With the correct configuration you can even cause the clients to mount a remote file-system via NFS and have a diskless thin-client system. TFTP Setup TFTP is a very simple file-transfer protocol, which is very similar to FTP but which doesn't use any kind of authentication. If you're not already running a TFTP server you can install one by running: root@itchy:~# apt-get install tftpd-hpa Once installed you'll need to enable it by editing the file /etc/default/tftpd-hpa. You should change RUN_DAEMON to yes, leaving you with contents like these:

  1. Defaults for tftpd-hpa

RUN_DAEMON="yes" OPTIONS="-l -s /var/lib/tftpboot" Now create the root directory, if it is missing, and start the server: root@itchy:~# mkdir -p /var/lib/tftpboot root@itchy:~# /etc/init.d/tftpd-hpa start Starting HPA's tftpd: in.tftpd. Once our systems have retrieved an IP address via DHCP they will request files from beneath the /var/lib/tftpboot root directory. We'll come back to the contents of this directory shortly. DHCP Setup If you don't already have a DHCP server configured upon your LAN you'll need to install one. If you're using a small home router, or similar, to provide local DHCP services you must disable this first. (Since we require the DHCP server to pass back some extra options to clients which the majority of routers won't allow). Discussing a full DHCP installation is mostly beyond the scope of this introduction but the thing we're trying to do is fairly simple. The goal of the DHCP server in this setup is twofold: • We obviously want to use it to allow clients to request and receive an IP address. • We want to cause the DHCP "answer" to give some extra details to the clients which are requesting an address: o The address of the TFTP server. o The initial filename to request from the TFTP server. The most common DHCP server is the dhcp-server package, and you can install this by running: root@itchy:~# apt-get install dhcp3-server Once installed the server is configured in the file /etc/dhcp3/dhcpd.conf, and there are a lot of available options described there. For our example we'll use the following configuration: option domain-name-servers 62.31.64.39, 62.31.112.39; default-lease-time 86400; max-lease-time 604800; authoritative;

subnet 192.168.1.0 netmask 255.255.255.0 {

       range 192.168.1.70 192.168.1.100;
       filename "pxelinux.0";
       next-server 192.168.1.50;
       option subnet-mask 255.255.255.0;
       option broadcast-address 192.168.1.255;
       option routers 192.168.1.1;

} Here we've configured the server to give out IP addresses from the range 192.168.1.70-100, set the default gateway to be 192.168.1.1 and use our ISP's nameservers. We've also used next-server to point to the TFTP server we're using (which is the same host as our DHCP server, but doesn't need to be). We've chosen the default name of pxelinux.0 as the name of the file for booting clients to request. Using dnsmasq instead Personally I use the dnsmasq package to provide DHCP services upon my LAN, since this is small and simple and provides other useful abilities, setting up PXE booting with dnsmasq just requires the addition of the following line to /etc/dnsmasq.conf: dhcp-boot=pxelinux.0,itchy,192.168.1.50 (Again we've setup the filename along with the name and IP address of the TFTP server which is "itchy" / 192.168.1.50 in this example) Restarting the service after this change is as simple as: root@itchy:~# /etc/init.d/dnsmasq restart Restarting DNS forwarder and DHCP server: dnsmasq. PXE Configuration Now that we've configured the TFTP and DHCP servers we need to go back and complete the configuration. By default when a client boots up it will use its own MAC address to specify which configuration file to read - however after trying several options it will fall back to requesting a default file. We need to create that that file, which will contain the list of kernels which are available to boot, we'll firstly need to create a directory to hold it: root@itchy:~# mkdir /var/lib/tftpboot/pxelinux.cfg Now save the following as /var/lib/tftpboot/pxelinux.cfg/default: DISPLAY boot.txt

DEFAULT etch_i386_install

LABEL etch_i386_install

       kernel debian/etch/i386/linux
       append vga=normal initrd=debian/etch/i386/initrd.gz  --

LABEL etch_i386_linux

       kernel debian/etch/i386/linux
       append vga=normal initrd=debian/etch/i386/initrd.gz  --

LABEL etch_i386_expert

       kernel debian/etch/i386/linux
       append priority=low vga=normal initrd=debian/etch/i386/initrd.gz  --

LABEL etch_i386_rescue

       kernel debian/etch/i386/linux
       append vga=normal initrd=debian/etch/i386/initrd.gz  rescue/enable=true --

PROMPT 1 TIMEOUT 0 This file instructs the client to display the contents of the file boot.txt so create that too: - Boot Menu -

=

etch_i386_install etch_i386_linux etch_i386_expert etch_i386_rescue The only remaining job is to download the official Etch installer kernel and associated files and save them in the directories specified in the default file we created: root@itchy:~# cd /var/lib/tftpboot/ root@itchy:~# wget http://ftp.uk.debian.org/debian/dists/etch/main/installer-i386/current/images/netboot/debian-installer/i386/pxelinux.0

root@itchy:~# mkdir -p /var/lib/tftpboot/debian/etch/i386 root@itchy:~# cd /var/lib/tftpboot/debian/etch/i386 root@itchy:~# wget http://ftp.uk.debian.org/debian/dists/etch/main/installer-i386/current/images/netboot/debian-installer/i386/linux root@itchy:~# wget http://ftp.uk.debian.org/debian/dists/etch/main/installer-i386/current/images/netboot/debian-installer/i386/initrd.gz When these commands have been completed we'll have the following structure: root@itchy:~# tree /var/lib/tftpboot/ /var/lib/tftpboot/ |-- boot.txt |-- debian | `-- etch | `-- i386 | |-- initrd.gz | `-- linux |-- pxelinux.0 `-- pxelinux.cfg

   `-- default

4 directories, 5 files (We only used debian/etch here in case we want to offer other installers in the future. You can put everything in one directory if you wish, just update pxelinux.cfg/default to match.) We should now be ready to test the setup. We've installed a pxelinux.0 file which will instruct booting clients to request pxelinux.cfg/default. This will then make a list of boot options available, which are displayed by the simple boot menu file we created. The files which are used for booting are stored beneath the TFTP root directory and thus accessible to booting clients. Sample Run A sample remote boot looks like this: PXE entry point found (we hope) at 9AE5:00D6 My IP address seems to be C0A80146 192.168.1.70 FTFTP prefix: Trying to load: pxelinux.cfg/01-00-14-22-a1-53-85 Trying to load: pxelinux.cfg/C0A80146 Trying to load: pxelinux.cfg/C0A8014 Trying to load: pxelinux.cfg/C0A801 Trying to load: pxelinux.cfg/C0A80 Trying to load: pxelinux.cfg/C0A8 Trying to load: pxelinux.cfg/C0A Trying to load: pxelinux.cfg/C0 Trying to load: pxelinux.cfg/C Trying to load: pxelinux.cfg/default - Boot Menu -

=

etch_i386_install etch_i386_linux etch_i386_expert etch_i386_rescue As you can see the system here attempted to load several configuration files, based upon its MAC address (01-00-14-22-a1-53-85) initially then falling back to the octets in the IP address it was given by DHCP (192.167.1.70). Finally it managed to load a working configuration using the last-chance default file we created. This in turn instructed it to show the boot menu we created. From here on the system will boot into whichever kernel you specify. (We could configure the system to timeout here and just boot into a default option, but we didn't.)