Difference between revisions of "RPI vcgencmd usage"

From eLinux.org
Jump to: navigation, search
m
(One intermediate revision by the same user not shown)
Line 77: Line 77:
  
 
If you also follow the instructions in this [http://www.raspberrypi.org/phpBB3/viewtopic.php?p=269992#p269992 Forum post] then the codec options for VP6 and VP8 (WEBM) also work, this is experimental and unsupported at present so any changes are at your own risk.
 
If you also follow the instructions in this [http://www.raspberrypi.org/phpBB3/viewtopic.php?p=269992#p269992 Forum post] then the codec options for VP6 and VP8 (WEBM) also work, this is experimental and unsupported at present so any changes are at your own risk.
 +
 +
 +
'''<code>vcgencmd get_config ''[config|int|str]''</code>'''
 +
Will print the configurations you have set. Argument can ether be a specific option or int, showing all configs with number-datatype, or str showing all conifgurations with datatype sting (aka text).
 +
vcgencmd get_config int
 +
arm_freq=1000
 +
core_freq=500
 +
sdram_freq=600
 +
over_voltage=6
 +
disable_overscan=1
 +
force_pwm_open=1
 +
  
 
'''<code>vcgencmd get_mem ''arm/gpu''</code>'''
 
'''<code>vcgencmd get_mem ''arm/gpu''</code>'''
Line 83: Line 95:
 
  arm=448M
 
  arm=448M
 
  gpu=64M
 
  gpu=64M
 +
  
 
'''<code>vcgencmd version</code>'''
 
'''<code>vcgencmd version</code>'''
Line 95: Line 108:
  
 
Parameters and function of other commands are not known.
 
Parameters and function of other commands are not known.
 +
 +
== Links ==
 +
* [https://github.com/nezticle/RaspberryPi-BuildRoot/wiki/VideoCore-Tools This list] also lists and describes vcgencmd options

Revision as of 22:00, 4 June 2013

Verified commands

Command outputs are from firmware version 362371.


vcgencmd commands

Shows a list of possible commands.

root@raspberrypi:~# vcgencmd commands
commands="vcos, ap_output_control, ap_output_post_processing, vchi_test_init, vchi_test_exit,
pm_set_policy, pm_get_status, pm_show_stats, pm_start_logging, pm_stop_logging, version, commands,
set_vll_dir, led_control, set_backlight, set_logging, get_lcd_info, set_bus_arbiter_mode,
cache_flush, otp_dump, codec_enabled, measure_clock, measure_volts, measure_temp, get_config,
hdmi_ntsc_freqs, render_bar, disk_notify, inuse_notify, sus_suspend, sus_status, sus_is_enabled,
sus_stop_test_thread, egl_platform_switch, mem_validate, mem_oom, mem_reloc_stats, file,
vctest_memmap, vctest_start, vctest_stop, vctest_set, vctest_get"


vcgencmd measure_clock <clock>

Shows clock frequency, clock can be one of arm, core, h264, isp, v3d, uart, pwm, emmc, pixel, vec, hdmi, dpi.

root@raspberrypi:~# \
> for src in arm core h264 isp v3d uart pwm emmc pixel vec hdmi dpi ; do \
>     echo -e "$src:\t$(vcgencmd measure_clock $src)" ; \
> done
arm:    frequency(45)=700000000
core:   frequency(1)=250000000
h264:   frequency(28)=0
isp:    frequency(42)=250000000
v3d:    frequency(43)=250000000
uart:   frequency(22)=3000000
pwm:    frequency(25)=0
emmc:   frequency(47)=100000000
pixel:  frequency(29)=154000000
vec:    frequency(10)=0
hdmi:   frequency(9)=163682000
dpi:    frequency(4)=0


vcgencmd measure_volts <id>

Shows voltage. id can be one of core, sdram_c, sdram_i, sdram_p, and defaults to core if not specified.

root@raspberrypi:~# \
> for id in core sdram_c sdram_i sdram_p ; do \
>     echo -e "$id:\t$(vcgencmd measure_volts $id)" ; \
> done
core:   volt=1.20V
sdram_c:        volt=1.20V
sdram_i:        volt=1.20V
sdram_p:        volt=1.23V


vcgencmd measure_temp

Shows core temperature of BCM2835 SoC.

root@raspberrypi:~# vcgencmd measure_temp
temp=42.8'C


vcgencmd codec_enabled <codec>

Shows if the specified codec is enabled, codec can be one of H264, MPG2, WVC1, MPG4, MJPG, WMV9. Please note this was run on a Pi with the MPG2 and VC1 licences enabled.

root@raspberrypi:~# \
> for codec in H264 MPG2 WVC1 MPG4 MJPG WMV9 ; do \
>     echo -e "$codec:\t$(vcgencmd codec_enabled $codec)" ; \
> done
H264:   H264=enabled
MPG2:   MPG2=enabled
WVC1:   WVC1=enabled
MPG4:   MPG4=enabled
MJPG:   MJPG=enabled
WMV9:   WMV9=enabled

If you also follow the instructions in this Forum post then the codec options for VP6 and VP8 (WEBM) also work, this is experimental and unsupported at present so any changes are at your own risk.


vcgencmd get_config [config|int|str] Will print the configurations you have set. Argument can ether be a specific option or int, showing all configs with number-datatype, or str showing all conifgurations with datatype sting (aka text).

vcgencmd get_config int
arm_freq=1000
core_freq=500
sdram_freq=600
over_voltage=6
disable_overscan=1
force_pwm_open=1


vcgencmd get_mem arm/gpu Shows how many memory is used by the CPU (arm) and GPU.

root@raspberrypi:~# vcgencmd get_mem arm && vcgencmd get_mem gpu
arm=448M
gpu=64M


vcgencmd version

Shows the firmware version

root@raspberrypi:~# vcgencmd version
Jan 13 2013 16:24:29
Copyright (c) 2012 Broadcom
version 362371 (release)


Parameters and function of other commands are not known.

Links

  • This list also lists and describes vcgencmd options