Difference between revisions of "RPi Tutorial EGHS:Switch Input"
m (→PullUp/PullDown) |
m (→PullUp/PullDown) |
||
Line 70: | Line 70: | ||
''This is covered in a lot more detail here (although note the logic level here is 5V!) <ref>http://www.ladyada.net/learn/arduino/lesson5.html Arduino inputs</ref>.'' | ''This is covered in a lot more detail here (although note the logic level here is 5V!) <ref>http://www.ladyada.net/learn/arduino/lesson5.html Arduino inputs</ref>.'' | ||
+ | |||
+ | |||
One additional thing to note is that the RPi GPIO has internal Pull-Up and Pull-Down resistors which can be enabled through software registers. This means that you can avoid the extra circuit above and simply place a switching circuit between Vcc or GND, but you have to set the registers correctly for it to function correctly. To keep the software simple and to avoid any damage, it is recommended you start with using external Pull-Ups and Pull-Downs until you are confident setting these registers correctly. | One additional thing to note is that the RPi GPIO has internal Pull-Up and Pull-Down resistors which can be enabled through software registers. This means that you can avoid the extra circuit above and simply place a switching circuit between Vcc or GND, but you have to set the registers correctly for it to function correctly. To keep the software simple and to avoid any damage, it is recommended you start with using external Pull-Ups and Pull-Downs until you are confident setting these registers correctly. |
Revision as of 03:52, 13 March 2012
Back to the Hub, or the Tutorials page.
GPIO Hardware & Software Tutorials:
- GPIO Protection Circuits
- Basic Circuits: LED output - DC motor - Switch Input - Analogue Sensor
- Intermediate Circuits: Shift Registers - Analogue to Digital - Driving Circuit - Alpha-Numeric Display
- Advanced Circuits: Control Hardware Over The Internet
This page is part of a work in progress.
Warnings
While most of these circuits may interface directly to the RPi, the use of a buffered interface (such as the one supplied by the Gertboard) is recommended which will help protect against damage. Alternatively, experiment with one of the Alternative Test Platforms.
Extreme caution should be exercised when interfacing hardware at a low level, you may damage your RPi, your equipment and potentially yourself and others. Doing so is at your own risk!
Aims
Note: Until RPi devices are available, I can not confirm this will work on a real RPi. For now, I shall be using the TI LaunchPad (see Alternative Test Platforms for details) to test the hardware on (as it is cheap and the logic levels similar).
The Hardware
Theory
Work in progess...
The GPIO pin on the RPi when defined as an Input allows the state of the pin to be read as with HIGH or LOW. This allows us to use a simple switch to set the state of the pin and the software can read this and respond to the change (i.e. change the audio volume output or light an LED wired to another pin).
For additional theory see [1]
Logic Levels
For the GPIO pin to determine if an input level is HIGH or LOW it has to detect that the voltage on the pin is above or below a set level, you should aim to set the pin to 10% of the logic voltage (HIGH for the RPi this is 3.3V - so 2.97V to 3.3V, LOW is 0V to 0.33V).
If the pin voltage is somewhere between 2.97V and 0.33V then the system may not reliably determine if a HIGH or LOW value is set (particularly as you get closer to 1.65V (halfway)).
If you drive voltages over 3.3V or negative voltages then you will risk damaging the internal GPIO circuits and perhaps even killing the RPi (which is why using extra components to protect and buffer inputs is recommended).
PullUp/PullDown
When a GPIO pin is disconnected and set as an input, the voltage is considered floating since there is no defined voltage level being applied to the pin. Therefore a good input circuit needs to apply either a HIGH voltage or a LOW voltage.
The top circuit with Switch 1 (Double-poll switch) is fine, however, when using other types of switches, such as Switch 2 (i.e. Single-poll switch) you will create a short-circuit when the switch is pressed!
However, by simply using a resistor in-between the short-circuit can be avoided. The value of the resistor is determined by the leakage current of the GPIO pin (the current used by the circuit to read the pin) (although this is not specified for the RPi, it is expected to be in the range of 1uA) and the amount of voltage drop it creates as a result.
If we set R1 to 10kohms, and max drop from Vcc is 10% (0.33V). Max leakage current = Vdrop/R1 = 0.33/10000 = 33uA
By picking a large resistor it ensures less current is drawn by the circuit, when the switch is active (this is why a large value of 10Kohms is usually used).
Current drawn = Vcc/R1 = 3.3/10000 = 0.33mA
The above circuit shows Switch 1 which when pressed will provide a LOW signal to the GPIO pin (otherwise the resistor pulls the circuit UP HIGH), and Switch 2 which when pressed will provide a HIGH signal to the GPIO pin (otherwise the resistor pulls the circuit DOWN LOW).
This is covered in a lot more detail here (although note the logic level here is 5V!) [2].
One additional thing to note is that the RPi GPIO has internal Pull-Up and Pull-Down resistors which can be enabled through software registers. This means that you can avoid the extra circuit above and simply place a switching circuit between Vcc or GND, but you have to set the registers correctly for it to function correctly. To keep the software simple and to avoid any damage, it is recommended you start with using external Pull-Ups and Pull-Downs until you are confident setting these registers correctly.
Output Protection
http://www.ladyada.net/learn/arduino/lesson5.html
Circuit
The Software
While the RPi is not available, I can only confirm the TI LaunchPad code works for me.
TI LaunchPad
The specifics and background behind the code is detailed very well on the following sites:
MSP430 LaunchPad Interrupt vs Polling
Sample test code for switch input (tested on TI MSP430G2553 device).
Circuit
Code:
RPi
References
|