RPi Xorg rpi Driver
This is the documentation for the Xorg Raspberry Pi driver developed in this thread 
By default, each Raspberry Pi Linux distro uses the generic framebuffer driver to draw the X display. All rendering of the display is done by the CPU into off- or on-screen buffers which eventually are shown on the output by the scan-out hardware. As the CPU on the Raspberry Pi is reasonably weak this makes for a sluggish user interface that at the same time causes a high CPU load, that slows down other programs.
In the modern 2D X11 desktop environment however there are two major ways that an application can choose to render itself,
- all rendering done by the X server
- nearly all rendering done by the application, with the X server simply presenting the rendered output
The primary goals of this project are to improve the performance of the first case and leave the second to other projects - there are many different user libraries that can do application-side rendering and boosting the performance of each of those would be a huge undertaking. The driver accomplishes this by offloading common tasks onto other hardware on the SoC that can process the work asynchronously, allowing the X server to be pre-empted by the OS yet still allowing progress to be made. This should allow other processes to see more CPU time.
Unfortunately this means that even if the X server runs infinitely faster, applications can still seem unresponsive if extensive application-side rendering is used. This is a common problem in optimisation. 
No effort has been made so far to allow applications access to OpenGL/GL ES through the X server eg via GLX - basic 2D has been the priority so far.
Xorg provides a mechanism for drivers to accelerate a number of important rendering tasks. This is called EXA . EXA allows easy overriding of,
- block copy aka blitting
- solid colour fills
- compositing, aka alpha blending
This driver implements the required functionality of EXA by using different parts of the Raspberry Pi SoC.
- 2D A->B block copies are performed using asynchronous DMA. A DMA engine is programmed to copy - in either a linear or 2D fashion - from A(x, y) to B(x2, y2) with an incrementing source address and incrementing destination address.
- Solid colour fills are also performed by asynchronous DMA. A DMA engine is programmed to copy (again either linear or 2D) from a non-moving source address to a moving destination address starting at B(x, y). The source address holds the colour that is to be used in the fill.
DMA commands are enqueued one after the other to ensure correct results. They are constructed as a chain of DMA control blocks (CBs), and passed to the DMA controller to be kicked in one go.
For cases where the DMA set-up time would take longer than a naive CPU copy or fill, a CPU fallback is used instead.
Composition is more complex as the inputs vary much more. The operation allows many different operating modes, eg with different filtering, transformations, pixel formats, blend equations, wrapping modes - but some operations are much more common than others. These are handled in three different ways:
- synchronous acceleration by the VPU's vector unit . This covers the fewest cases but ideally the ones in which the most pixels need to be processed, where a speed-up will be most appreciated. Hand coded in assembly.
- synchronous low-latency CPU implementation using 32-bit ARM SIMD, catching all common cases. This should perform a "good enough" job, as it is primarily designed for low-pixel-count operations, eg rendering small antialiased characters.
- fallback to the generic X implementation: this covers all other composition modes. This is the worst case, as the overhead reaching the first actual image processing instruction is high.
SoC hardware used
As mentioned above, the driver leverages three things that the generic driver wouldn't otherwise use.
ARM CPU SIMD
This is not as comprehensive  as the NEON instruction set found in some v7 ARM implementations but is still useful for the task of composition. Through C++ template metaprogramming, a careful consideration of what a compiler can and cannot optimise, and finally eyeballing the code generated we can have composition functions that are of a comparable speed to those hand-optimised functions in pixman. The templating helps here by generating hundreds of these functions, rather than the handful that are specially implemented in pixman.
The Raspberry Pi SoC includes a decent number of DMA engines which can be used by the ARM for moving data around memory. They can all access the full bandwidth of the memory - more than the ARM could itself. They all share the bandwidth, and one DMA is sufficient to saturate the bus. The DMA engines are not all the same however - some have greater performance or features than the others. For instance, half of them have the ability to perform '2D' DMAs rather than straight linear transfers. Also one of the DMA engines (DMA zero) has a deeper FIFO allowing it to do larger read bursts.
The DMA hardware does not live within the same address space as the ARM CPU. It uses the bus address space instead. A translation must be made to the address to get from one to the other. Also, the ARM's page tables are not used by this hardware. Virtually contiguous ARM addresses are not necessarily physically contiguous the DMA hardware won't know about this - as a result DMA needs to be sometimes broken up into 4kb blocks to ensure the correct result.
There is a start-up cost associated with DMA, and as a result sometimes it is not efficient to use this hardware. Steps include,
- breaking a large transfer up into something which respects 4kb page boundaries
- entering the kernel
- translating user virtual addresses into bus addresses for each DMA CB
- flushing and invalidating parts of the data cache, then kicking off the DMA chain
- returning to user mode to do more work
- entering the kernel
- waiting for the DMA to complete
- returning to user mode
For reference, a user->kernel->user transition takes roughly 1 us. Each DMA CB appears to take the DMA engine around 5 us to start.
Also on the SoC is the a custom processor that appears to be the controlling brains of the GPU, the VPU. This is what the 'firmware' runs on. Rpi_Software#Overview
Within this processor is a 16-way vector unit which is well-suited to image processing operations. Although this processor is ordinarily clocked nearly three times slower than the ARM core, the vector unit and improved memory interface more than make up for it. Some composition functions that commonly operate on thousands of pixels have been coded to run on this unit.
Like the DMA hardware, it lives within the bus address memory space. User virtual ARM addresses need translation, and the 4kb page boundary/page table issues still apply. Also from the viewpoint of the driver the VPU appears as an asynchronous co-processor: there is a ~56 us overhead at stock clock speeds communicating with it from X so work should really only be sent to it if worthwhile.
The workload sent to the driver from the running applications is not known in advance. The structure of the work is generally the same though. Allocate some images, upload some data from the user application, perform a handful of operations, synchronisation point. Perform some more operations, synchronisation point.
The point of the frequent synchronisation points is to allow the application to get a hold of the rendered pixel data. It is also there to allow the application to release memory. By knowing that all rendering has completed by a given point, it knows what is sees in the buffer is correct and also that a given image buffer is no longer in use and can be freed.
This behaviour is contrary to a game-style render loop: for the majority of a frame a command buffer is filled with drawing commands. At the end of a frame this command buffer is sent to the GPU for processing. However whilst this was going on, the GPU was processing the last frame's command buffer. This contrasts the X update loop as,
- there are many more synchronisation points, and it is unknown when they will appear
- there is not a double-buffered command buffer, meaning the GPU cannot be processing "last frame's image" whilst the CPU is building this frame's command buffer
- image data cannot go too far away from the CPU as the application may want to inspect it with the minimum of delay
This means OpenGL and other run-times are not appropriate for an X driver on a system like the Raspberry Pi that lacks horsepower. If GL or a similar run-time was used, the high CPU cost of setting up and tearing down images and command lists etc would drawf the actual amount of time the GPU would be doing rendering. Also the fact that on the Raspberry Pi textures are not trivially accessible by the CPU means that when an application needs to gain access to pixel data a high cost must be paid stopping the GPU and then downloading the textures. Even the 6 us start-up time of a DMA CB is noticeable in some applications - if instead the whole 3D stack is traversed many applications would be far slower than the generic CPU route.
That said applications which expect the driver to be implemented on a run-time like OpenGL will tailor their workload to properly suit it. For example, the Chromium browser. This is an exception though - most applications expect a synchronous driver with easily-reachable memory
When to synchronise
As mention before, the driver treats the VPU and DMA hardware as asynchronous co-processors. The CPU overhead of reaching them is relatively high and as CPU time is not in abundance this overhead needs to be amortised over as many operations as possible. This means the CPU builds up a list of work to send to the DMA hardware and a list of work to send to the VPU hardware. Eventually these lists are sent off for processing. The overhead cost is only paid once.
Yet as it is not known when a synchronisation point may appear it is not clear when a DMA or VPU command list must be started. By waiting longer the overhead is decreased (per unit of work) yet there is a greater chance that the application requests the work is finished, but it won't be as it has yet to start. The application then blocks. The opposite is also true - if work is kicked too frequently, too much overhead results yet the application will wait less as there is a greater chance the work has completed by the time it requests a sync point.
Performing composition with the VPU is tricky too - as there is a 56 us start-up cost to performing work there, are there sufficient pixels to process that it is worth this cost? An estimate needs to be made of the relative speeds of the two processors (ARM and VPU) and based on this a decision is made whether the task is run on the co-processor or not. Something to also consider is that on the ARM CPU the run-time is variable. There are early-out optimisations that can be performed based on the value of the mask (if present). These optimisations can't be used on the VPU.
Finally there is also the case where work to be processed with DMA is so small that it would be quicker to process on the CPU. Yet if a million tiny pieces of work come along back-to-back it would still have been faster to do with DMA - but it is not known how many pieces of work will be enqueued. This means there is a decision to be made: when should the CPU perform work that it thinks it could do faster than the DMA hardware?
High-level driver layout
Yellow represents "the driver", code that has been written as part of this project.
In order to suit different situations, there are three main ways of using the driver. Each has advantages and disadvantages. Due to the way EXA is currently being used, it needs to track a large chunk of "offscreen memory". This is memory that the application can't see, yet the graphics accelerator (in whatever form the driver writer is targetting) can see. The problem comes in the Raspberry Pi's case is that all the hardware targetted can see all the memory, and so this abstraction is unnecessary and wasteful. This limitation incurs a decent performance penalty, but work will be done in the future to address this issue.
Here are the three ways of providing EXA and the driver with its offscreen memory.
4 kb page mode
In order for DMA to function, the the memory being operated on must not move to a different physical address by the Linux page compaction system nor be paged out to swap. This will happen to normal user pages, so they are not suitable. One way to get around this is to allocate pages from the kernel and map them in to the user space. These pages are unmoveable, they will never be swapped and their physical addresses can be cached for a more efficient translation.
The advantages for this scheme include:
- no wasted memory - if X does not use the whole of the offscreen space, then only the pages that are used are allocated. No pre-declaration or reservation of memory is necessary.
- it is the most robust and secure system, as all address translations are vetted by the kernel, and the hardware that is provided the addresses is simple and predictable.
- the maximum memory can be scaled up and down at run-time, without a reboot
The disadvantages are based around the fact that memory is not physically contiguous:
- DMA must be broken at the 4 kb page boundary into separate DMA transfers (still as part of the CB chain though)
- VPU composition cannot be used
- 2D DMA cannot be used due to the complexity of breaking at page boundaries
- more CPU address translation is necessary due to the increase in CBs
Finally, as the pages are unmoveable they cannot be swapped out - this will increase the pressure on the remaining 'normal' memory.
- the address translation is generally more complex, increasing the ARM CPU load
With all three memory options, all on-screen pixmaps that are not under the control of EXA are allocated with the 4 kb mode in order to allow DMA to pull them into offscreen memory.
Boot-time reservation mode
This mode involves telling the kernel to simply ignore - at boot-time - a chunk of the memory provided to the CPU. It is never used by applications or the kernel as the system simply believes it has less memory attached. This reserved memory can be mapped in as the offscreen buffer to good effect. It is physically continuous, and this means address translation is very simple. Just one constant needs to be added to the user virtual address to get to the final bus address needed by DMA and the VPU. If the mapping is done smartly, no offset is needed at all.
- DMA does not need to be broken into 4 kb chunks
- VPU composition can be used
- 2D DMA can function
- address translation is very simple
- memory is wasted if it is not used, either by X not needing it all or the user simply not running X in the first place
- a reboot is needed to change the reservation size
- the user needs to compute the address of the reservation before passing it to X
- there is generally a greater chance of something "going wrong" due to user or programmer error (there's no problem inherent to the technique, though)
VideoCore mailbox reservation mode
This involves asking the firmware for a block of memory from its share, and then mapping it in to the user process. This can function either in the static split mode, where the user declares how much is needed for the GPU in their config.txt (eg 192/64) or via the new "floating split" CMA mode. The size of the split grows and shrinks based on what's happening at that time.
- DMA does not need to be broken into 4 kb chunks
- VPU composition can be used
- 2D DMA can function
- address translation is very simple
- easy user set-up
- no wasted memory if X is not used
- memory usage can be changed without a reboot
- if not in the CMA mode, this may prevent 3D applications from starting as there may be insufficient GPU memory
Configuration of the driver
There are a number of different 'Options' that can be passed to the driver at load-time. These can be added to the default configuration file I supply.
|Option name||Suitable inputs||Explanation|
|AccelMethod||EXA, EXA_NULL, anything else||
|FaultInImm||true/false||This is really only useful for people who choose to find their EXA offscreen memory RPi_Xorg_rpi_Driver#Memory_layout via the 4 kb method. As memory is allocated lazily (ie when it is first used) you will have a slowly increasing memory load. This can cause trouble for the Ethernet/USB driver, plus cause occasional slow-downs.
By choosing yes here all pages allocated via the 4 kb method will be allocated and locked up-front. Only use if you're seeing trouble in dmesg related to memory allocations.
|BlockBase||an address, in decimal or hexadecimal.||If you choose to use the boot-time reservation you will need to use this option to configure where your memory hole is. You can derive this address yourself, or sort of look it up in /proc/iomem. Let's say you reserve 123 MB for the driver and you choose to use the a 240/16 MB CPU/GPU split in config.txt. The address will be (240 - 123) * 1048576.
You will be able to see this by looking in /proc/iomem at the first entry: "System RAM". It will say 00000000-<some number in hex>. <some number> will be (240 - 123) * 1048576 - 1. Easy.
|BlockSize||a number of bytes, in decimal or hexadecimal||This is the maximum number of bytes you would like to use as the driver's offscreen memory. You should realistically use over 8 MB - I would say this would be a minimum for 1280x1024x32. 16 MB would be a realistic minimum for 1080p.
Nothing should fail if you get it too small (although it will stop and caution you at load-time if you choose a number silly small), there will simply be more swapping back and forth ie worse performance. For users who use the boot-time reservation this number should really be the size of the hole that you reserve. It can be smaller (pointless) but no bigger.
|MemMode||4k, mem, vc||
|VpuOffload||true, false||This toggles whether large composition operations will be offloaded to the VPU, assuming the blending function and pixel formats match. This is a highly-experimental feature and can lock up your Raspberry Pi and/or corrupt your SD card.
This makes use of information derived through reverse engineering and should not be used in countries where this is prohibited.
|MboxFile||a filename||This should point to a special character device file, with major 100 minor 0. Only needs to be set if VPU offloading is used.|
|VpuElf||a filename||This should point to a special binary which is to be run on the VPU and provides the VPU offload functionality. Not necessary if VPU offload is disabled.|
|VerboseReporting||true, false||Turns on the stats the show what the EXA system is handing to the driver, broken down by each function, the number of pixels being pushed by each part, and which part of the SoC is doing what work.|