User:Millerap - Revision history

Yoder at 15:16, 18 May 2013

2013-05-18T15:16:58Z

2012-11-08T16:47:09Z

Replaced content with "Um"

2012-09-04T16:25:52Z

2012-08-31T23:29:51Z

Created page with "Category:ECE497"

New page

[[Category:ECE497]]

@@ Line 1: / Line 1: @@
-[[Category:ECE497]]
+[[Category:ECE497 |Um]]
-−
-=== Introduction ===
-−
-This Page is my personal reference to my work in ECE497. All of the command line arguments are designed to run on Ubuntu 12.04.
-−
-=== Connecting to the BeagleBone ===
-−
-In order to Connect to the BeagleBone we can use screen or ssh. Its a good idea to install screen before getting started:
-  host$ '''sudo apt-get install screen'''
-−
-Before plugging in the BeagleBone, run the following:
-  host$ '''ls /dev/tty* > /tmp/tty'''
-−
-Then, After plugging in the BeagleBone, run the following to show which USB the Bone is plugged into:
-  host$ '''ls /dev/tty* > /tmp/tty2'''
-  host$ '''diff /tmp/tty*'''
-a99, 100
-  > /dev/ttyUSB0
-  > /dev/ttyUSB1
-  host$ '''sudo screen /dev/''ttyUSB1'' 115200'''
-−
-USB0 and USB1 are both listed when plugging in the Bone, but after attempting to connect to each of them (next) I found that ttyUSB1 was the Bone.
-−
-Press '''Return''' to start the Angstrom software, and login as '''root'''
-−
-Congratulations you are now connected to the BeagleBone.
-−
-Once logged in to root on the Bone, you can eject the Bone and run:
-  beagle$ '''ifconfig'''
-−
-listed under usb0, is (in my case) '''inet addr:192.168.7.2 Bcast:192.168.7.3 Mask:255.255.255.252'''
-−
-Using ssh we can also connect to the Bone:
-  host$ '''ssh -X root@192.168.7.2'''

← Older revision		Revision as of 16:25, 4 September 2012
Line 1:		Line 1:
	[[Category:ECE497]]		[[Category:ECE497]]
		+
		+	=== Introduction ===
		+
		+	This Page is my personal reference to my work in ECE497. All of the command line arguments are designed to run on Ubuntu 12.04.
		+
		+	=== Connecting to the BeagleBone ===
		+
		+	In order to Connect to the BeagleBone we can use screen or ssh. Its a good idea to install screen before getting started:
		+	host$ '''sudo apt-get install screen'''
		+
		+	Before plugging in the BeagleBone, run the following:
		+	host$ '''ls /dev/tty* > /tmp/tty'''
		+
		+	Then, After plugging in the BeagleBone, run the following to show which USB the Bone is plugged into:
		+	host$ '''ls /dev/tty* > /tmp/tty2'''
		+	host$ '''diff /tmp/tty*'''
		+	98a99, 100
		+	> /dev/ttyUSB0
		+	> /dev/ttyUSB1
		+	host$ '''sudo screen /dev/''ttyUSB1'' 115200'''
		+
		+	USB0 and USB1 are both listed when plugging in the Bone, but after attempting to connect to each of them (next) I found that ttyUSB1 was the Bone.
		+
		+	Press '''Return''' to start the Angstrom software, and login as '''root'''
		+
		+	Congratulations you are now connected to the BeagleBone.
		+
		+	Once logged in to root on the Bone, you can eject the Bone and run:
		+	beagle$ '''ifconfig'''
		+
		+	listed under usb0, is (in my case) '''inet addr:192.168.7.2 Bcast:192.168.7.3 Mask:255.255.255.252'''
		+
		+	Using ssh we can also connect to the Bone:
		+	host$ '''ssh -X root@192.168.7.2'''