Difference between revisions of "Userspace Arduino"
(→Beaglebone Black) |
(→Getting Started) |
||
Line 45: | Line 45: | ||
* Copy the binary to the Beaglebone Black and execute! | * Copy the binary to the Beaglebone Black and execute! | ||
<br> | <br> | ||
− | == Using | + | == Using send_exec == |
− | * | + | * [https://github.com/prpplague/Userspace-Arduino/blob/master/utility/send_exec.sh send-exec] is a nice little upload and execute script, which has now been integrated with the Arduino-Userspace repository. It uses the scp protocol to copy binaries to the Beaglebone Black over USB ethernet and ssh to execute it. |
− | * | + | * To use it, simply do a |
+ | make upload | ||
+ | in the same directory where the makefile is located for the respective examples. | ||
+ | * If you want to avoid a password prompt, you can set-up the ssh keys for the Beaglebone Black: | ||
+ | cd ~/.ssh | ||
+ | ssh-keygen -t dsa #set password or you can leave it blank | ||
+ | ssh-copy-id -i ~/.ssh/id_dsa.pub root@$192.168.7.2 # replace id_dsa.pub by your public key file if some other name is given | ||
+ | ssh root@192.168.7.2 # login and enter password once | ||
+ | |||
+ | Here after, you won't be prompted for a password from this machine | ||
+ | |||
<br> | <br> | ||
+ | |||
= Boards Supported = | = Boards Supported = | ||
<br> | <br> |
Revision as of 12:59, 15 July 2013
Development Blogs for the Userspace Arduino project:
- Primary Blog for work on the project
- Parav Nagarsheth's Blog about his work on the project
- Anuj Deshpande's Blog about his work on the project
this page is to document some research on creating a userspace executable using the wiring and processing language used with Arduino.
Getting Started
Cloning
- Clone the repo from https://github.com/prpplague/Userspace-Arduino
git clone https://github.com/prpplague/Userspace-Arduino.git
Toolchain
BeagleBone Black
~$ wget http://www.angstrom-distribution.org/toolchains/angstrom-2011.03-x86_64-linux-armv7a-linux-gnueabi-toolchain.tar.bz2 ~$ sudo tar -C / -xzf angstrom-2011.03-x86_64-linux-armv7a-linux-gnueabi-toolchain.tar.bz2 ~$ export PATH=/usr/local/angstrom/arm/bin:$PATH ~$ export CROSS_COMPILE=arm-angstrom-linux-gnueabi-
MinnowBoard
- todo
Raspberry Pi
- todo
Running a demo
- Check out some of the examples in /path/to/Userscape-Arduino/Arduino-Makefile/examples. Currently only HelloWorldUserspace, BlinkUserspace and BaconDemo work.
cd Userspace-Arduino/arduino-makefile/examples/HelloWorldUserspace
- To make, while in the above directory:
make
- A binary HelloWorldUserspace.elf should be created in a directory build-userspace
- Copy the binary to the Beaglebone Black and execute!
Using send_exec
- send-exec is a nice little upload and execute script, which has now been integrated with the Arduino-Userspace repository. It uses the scp protocol to copy binaries to the Beaglebone Black over USB ethernet and ssh to execute it.
- To use it, simply do a
make upload
in the same directory where the makefile is located for the respective examples.
- If you want to avoid a password prompt, you can set-up the ssh keys for the Beaglebone Black:
cd ~/.ssh ssh-keygen -t dsa #set password or you can leave it blank ssh-copy-id -i ~/.ssh/id_dsa.pub root@$192.168.7.2 # replace id_dsa.pub by your public key file if some other name is given ssh root@192.168.7.2 # login and enter password once
Here after, you won't be prompted for a password from this machine
Boards Supported
Beaglebone Black
Initial development is being done with the Beaglebone Black and the Bacon_Cape
- if you have your beaglebone black loaded with a firmware image older that 07.11.2013, you will need copy the Bacon Cape dtbo file on to your beaglebone black
~# scp ~/Downloads/BB-BONE-BACONE-00A0.dtbo root@192.168.7.2:/lib/firmware/BB-BONE-BACONE-00A0.dtbo
Arduino Pin | BBB Header Pin | Function | Alternate Function |
---|---|---|---|
0 | P9_11 | UART (RXD) | |
1 | P9_13 | UART (TXD) | |
2 | P9_15 | GPIO | |
3 | P9_14 | PWM | |
4 | P9_12 | GPIO | |
5 | P9_16 | PWM | |
6 | P9_42 | PWM | |
7 | P8_19 | GPIO | PWM |
8 | P9_19 | I2C (SCL) | |
9 | P9_20 | I2C (SDA) | |
10 | P9_17 | GPIO | SPI_CS0 |
11 | P9_18 | GPIO | SPI_MOSI |
12 | P9_21 | SPI_MISO | |
13 | P9_22 | GPIO | SCK |
14 | USR LED 0 | LED | |
15 | USR LED 1 | LED | |
16 | USR LED 2 | LED | |
17 | USR LED 3 | LED | |
18 | P9_33 | AIN4 | |
19 | P9_35 | AIN6 | |
20 | P9_36 | AIN5 | |
21 | P9_37 | AIN2 | |
22 | P9_38 | AIN3 | |
23 | P9_39 | AIN0 | |
24 | P9_40 | AIN1 |
MinnowBoard
- Initial support started
- Need Lure accessory board for testing
Raspberry Pi
- support planned
- will use RPi_Gertboard for initial development
Transfer Options
Netcat
- GNU Netcat networking tool http://netcat.sourceforge.net/
- Can create a connection using nc -w 1 192.168.7.2 1114 < new.zip on the server (in this case the machine running the Energia IDE), and nc -lp 1114 > n.zip on the Beaglebone. 1114 is a random port number which has to be the same on client as well as server side.
- Some issue with sending .bin files directly. Mostly it was with how the file ends, not sure. So need to zip the file.
- Requires no authentication
- A script will be needed to listen on a particular port on the BBB for any incoming connections which will receive, unzip and execute the code.
ssh/sftp
- Needs ssh and sftp installed
- Need to configure keys initially. Works without user authentication after that
- Code to upload and execute binary here : https://github.com/anujdeshpande/send_exec
- To do :
- Create Sketchbook folder
- Fetch output if any, display it in the serial monitor
Emulating the Arduino bootloader
- The Arduino Bootloader uses a protocol similar to STK500v1 (over UART, though)
- One way to program (copy) the binaries would be to emulate the protocol on the bone over USB gadget and use AVRDude on the IDE side
- However this would be cumbersome, since the protocol was designed to write bytes to flash memory, not copy files.
- Energia uses mspdebug to flash the MSP430 using a serialized version of JTAG called Spy-Bi-Wire (SBW).
- File transfer protocols over serial like XMODEM and ZMODEM could be explored for an easier and more compatible option to Upload the binaries.
- Install the lrzsz package on both the host (PC) and the client (Beaglebone):
apt-get install lrzsz
- Connect the Beaglebone via USB and determine the port (for e.g. /dev/ttyUSB1). Once the OS is booted up, start the transfer:
sz -vv -b filename.bin < /dev/ttyUSB1 > /dev/ttyUSB1
HTTP post
- Send executable over port 80
- On BBB, listen for any uploads and execute them
Action List and Issues
- The Arduino 1.5 IDE has better support for arbitrary architectures than the Energia fork of Arduino. This could help since the architecture specific stuff has been moved to config files. Further investigation is needed. Should the Userspace implementation forked directly out of the Arduino IDE or should the current implementation continue?
- For development beyond the GSOC period, an option to get this upstream needs to be considered.
- The BBB needs a separate FTDI cable for serial ports. However, a /dev/ttyACM port is available over USB. It can be used for uploading via the normal bootloader way. After the upload, it can be used for serial read/write to the host (PC).
- A single protocol to tackle uploading via USB and ethernet and may not be feasible. Networking over USB is pretty unreliable and tough for newbies to get working. For ethernet upload, several of the above options can be considered. For USB, a simple bootloader emulator will do.