diff -u -rN -p linux-2.6.10/Documentation/filesystems/pramfs.txt linux-2.6.10-rbtx49/Documentation/filesystems/pramfs.txt --- linux-2.6.10/Documentation/filesystems/pramfs.txt 1970-01-01 09:00:00.000000000 +0900 +++ linux-2.6.10-rbtx49/Documentation/filesystems/pramfs.txt 2005-04-22 14:46:32.000000000 +0900 @@ -0,0 +1,183 @@ +PRAMFS Overview +=============== + +Many embedded systems have a block of non-volatile RAM seperate from +normal system memory, i.e. of which the kernel maintains no memory page +descriptors. For such systems it would be beneficial to mount a +fast read/write filesystem over this "I/O memory", for storing frequently +accessed data that must survive system reboots and power cycles. An +example usage might be system logs under /var/log, or a user address +book in a cell phone or PDA. + +Linux traditionally had no support for a persistent, non-volatile RAM-based +filesystem, persistent meaning the filesystem survives a system reboot +or power cycle intact. The RAM-based filesystems such as tmpfs and ramfs +have no actual backing store but exist entirely in the page and buffer +caches, hence the filesystem disappears after a system reboot or +power cycle. + +A relatively straight-forward solution is to write a simple block driver +for the non-volatile RAM, and mount over it any disk-based filesystem such +as ext2/ext3, reiserfs, etc. + +But the disk-based fs over non-volatile RAM block driver approach has +some drawbacks: + +1. Disk-based filesystems such as ext2/ext3 were designed for optimum + performance on spinning disk media, so they implement features such + as block groups, which attempts to group inode data into a contiguous + set of data blocks to minimize disk seeking when accessing files. For + RAM there is no such concern; a file's data blocks can be scattered + throughout the media with no access speed penalty at all. So block + groups in a filesystem mounted over RAM just adds unnecessary + complexity. A better approach is to use a filesystem specifically + tailored to RAM media which does away with these disk-based features. + This increases the efficient use of space on the media, i.e. more + space is dedicated to actual file data storage and less to meta-data + needed to maintain that file data. + +2. If the backing-store RAM is comparable in access speed to system memory, + there's really no point in caching the file I/O data in the page + cache. Better to move file data directly between the user buffers + and the backing store RAM, i.e. use direct I/O. This prevents the + unnecessary populating of the page cache with dirty pages. However + direct I/O has to be enabled at every file open. To enable direct + I/O at all times for all regular files requires either that + applications be modified to include the O_DIRECT flag on all file + opens, or that a new filesystem be used that always performs direct + I/O by default. + +The Persistent/Protected RAM Special Filesystem (PRAMFS) is a +full-featured read/write filesystem that has been designed to address +these issues. PRAMFS is targeted to fast I/O memory, and if the memory +is non-volatile, the filesystem will be persistent. + +In PRAMFS, direct I/O is enabled across all files in the filesystem, in +other words the O_DIRECT flag is forced on every open of a PRAMFS file. +Also, file I/O in the PRAMFS is always synchronous. There is no need +to block the current process while the transfer to/from the PRAMFS +is in progress, since one of the requirements of the PRAMFS is that the +filesystem exist in fast RAM. So file I/O in PRAMFS is always direct, +synchronous, and never blocks. + +The data organization in PRAMFS can be thought of as an extremely +simplified version of ext2, such that the ratio of data to meta-data is +very high. + +PRAMFS is also write protected. The page table entries that map the +backing-store RAM are normally marked read-only. Write operations into +the filesystem temporarily mark the affected pages as writeable, the +write operation is carried out with locks held, and then the pte is +marked read-only again. This feature provides some protection against +filesystem corruption caused by errant writes into the RAM due to +kernel bugs for instance. In case there are systems where the write +protection is not possible (for instance the RAM cannot be mapped +with page tables), this feature can be disabled with the CONFIG_PRAMFS_NOWP +config option. + +In summary, PRAMFS is a light-weight, full-featured, and space-efficient +special filesystem that is ideal for systems with a block of fast +non-volatile RAM that need to access data on it using a standard +filesytem interface. + + +Supported mount options +======================= + +The PRAMFS currently requires one mount option, and there are several +optional mount options: + +physaddr= Required. It tells PRAMFS the physical address of the + start of the RAM that makes up the filesystem. The + physical address must be located on a page boundary. + +init= Optional. It is used to initialize the memory to an + empty filesystem. Any data in an existing filesystem + will be lost if this option is given. The parameter to + "init=" is the RAM size in bytes. + +bs= Optional. It is used to specify a block size. It is + ignored if the "init=" option is not specified, since + otherwise the block size is read from the PRAMFS + super-block. The default blocksize is 2048 bytes, + and the allowed block sizes are 512, 1024, 2048, and + 4096. + +bpi= Optional. It is used to specify the bytes per inode + ratio, i.e. For every N bytes in the filesystem, an + inode will be created. This behaves the same as the "-i" + option to mke2fs. It is ignored if the "init=" option is + not specified. + +N= Optional. It is used to specify the number of inodes to + allocate in the inode table. If the option is not + specified, the bytes-per-inode ratio is used the + calculate the number of inodes. If neither the "N=" or + "bpi=" options are specified, the default behavior is to + reserve 5% of the total space in the filesystem for the + inode table. This option behaves the same as the "-N" + option to mke2fs. It is ignored if the "init=" option is + not specified. + +Examples: + +mount -t pramfs -o physaddr=0x20000000,init=0x2F000,bs=1024 none /mnt/pram + +This example locates the filesystem at physical address 0x20000000, and +also requests an empty filesystem be initialized, of total size 0x2f000 +bytes and blocksize 1024. The mount point is /mnt/pram. + +mount -t pramfs -o physaddr=0x20000000 none /mnt/pram + +This example locates the filesystem at physical address 0x20000000 as in +the first example, but uses the intact filesystem that already exists. + + +Current Limitations +=================== + +- The RAM used for PRAMFS must be directly addressable. + +- PRAMFS does not support hard links. + +- PRAMFS supports only private memory mappings. This allows most + executables to run, but programs that attempt shared memory + mappings, such as X apps that use X shared memory, will fail. + +Further Documentation +===================== + +If you are interested in the internal design of PRAMFS, there is +documentation available at the Sourceforge PRAMFS home page at +http://pramfs.sourceforge.net. + +Please send bug reports/comments/feed back to the pramfs development +list at sourceforge: pramfs-devel@lists.sourceforge.net. + + +ChangeLog +========= + +1.0.3: + - kernel 2.6.9. + - __ioremap() definition not consistent across archs, use + ioremap() instead. + - flush_tlb_kernel_page() is only available on some archs. + - fixed bug in pram_fill_super(): root inode pointer needs + to be recalculated after remapping whole fs. +1.0.2: + - kernel 2.6.4. + - use pram_truncate() in pram_delete_inode(). + - dangling pram_lock_inode() removed in pram_truncate_blocks(). + - edits to this README + +1.0.1: + - port to kernel 2.6.3. + - implement direct_IO() method instead of custom file read/write + methods. + - do away with __ioremap_readonly() requirement. + - implement inode truncate() method. + +1.0.0: + - Started ChangeLog (kernel 2.4.22). + diff -u -rN -p linux-2.6.10/arch/mips/Kconfig linux-2.6.10-rbtx49/arch/mips/Kconfig --- linux-2.6.10/arch/mips/Kconfig 2004-12-25 06:34:45.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/Kconfig 2005-04-22 14:46:19.000000000 +0900 @@ -845,6 +845,27 @@ config TOSHIBA_FPCIB0 bool "FPCIB0 Backplane Support" depends on TOSHIBA_RBTX4927 +config TX_RBTX4927 + bool "Support for TX RBTX4927" + +config TX_RBTX4938 + bool "Support for TX RBTX4938" + +config TX_BOARDS + bool + depends on TX_RBTX4927 || TX_RBTX4938 + default y + select BOOT_ELF32 + select IRQ_CPU + select DMA_NONCOHERENT + select HW_HAS_PCI + select ISA + select SWAP_IO_SPACE + +config PICMG_PCI_BACKPLANE_DEFAULT + bool "Support for PICMG PCI Backplane" + depends on TX_BOARDS + config RWSEM_GENERIC_SPINLOCK bool default y @@ -875,7 +896,7 @@ config DMA_NONCOHERENT config EARLY_PRINTK bool - depends on MACH_DECSTATION + depends on MACH_DECSTATION || TX_BOARDS default y config GENERIC_ISA_DMA @@ -1011,7 +1032,7 @@ config IT8712 config BOOT_ELF32 bool - depends on MACH_DECSTATION || MIPS_ATLAS || MIPS_MALTA || MOMENCO_JAGUAR_ATX || MOMENCO_OCELOT_3 || SIBYTE_SB1xxx_SOC || SGI_IP32 || SGI_IP22 || SNI_RM200_PCI + depends on MACH_DECSTATION || MIPS_ATLAS || MIPS_MALTA || MOMENCO_JAGUAR_ATX || MOMENCO_OCELOT_3 || SIBYTE_SB1xxx_SOC || SGI_IP32 || SGI_IP22 || SNI_RM200_PCI || TX_BOARDS default y config MIPS_L1_CACHE_SHIFT @@ -1025,41 +1046,6 @@ config ARC32 depends on MACH_JAZZ || SNI_RM200_PCI || SGI_IP22 || SGI_IP32 default y -config FB - bool - depends on MIPS_MAGNUM_4000 || OLIVETTI_M700 - default y - ---help--- - The frame buffer device provides an abstraction for the graphics - hardware. It represents the frame buffer of some video hardware and - allows application software to access the graphics hardware through - a well-defined interface, so the software doesn't need to know - anything about the low-level (hardware register) stuff. - - Frame buffer devices work identically across the different - architectures supported by Linux and make the implementation of - application programs easier and more portable; at this point, an X - server exists which uses the frame buffer device exclusively. - On several non-X86 architectures, the frame buffer device is the - only way to use the graphics hardware. - - The device is accessed through special device nodes, usually located - in the /dev directory, i.e. /dev/fb*. - - You need an utility program called fbset to make full use of frame - buffer devices. Please read - and the Framebuffer-HOWTO at - for more information. - - Say Y here and to the driver for your graphics board below if you - are compiling a kernel for a non-x86 architecture. - - If you are compiling for the x86 architecture, you can say Y if you - want to play with it, but it is not essential. Please note that - running graphical applications that directly touch the hardware - (e.g. an accelerated X server) and that are not frame buffer - device-aware may cause unexpected results. If unsure, say N. - config HAVE_STD_PC_SERIAL_PORT bool @@ -1111,6 +1097,13 @@ config TANBAC_TB0219 bool "Added TANBAC TB0219 Base board support" depends on TANBAC_TB0229 +config HEARTBEAT + bool "Use power LED as a heartbeat" + help + Use the power-on LED on your machine as a load meter. The exact + behavior is platform-dependent, but normally the flash frequency is + a hyperbolic function of the 5-minute load average. + endmenu menu "CPU selection" @@ -1394,6 +1387,15 @@ config NR_CPUS This is purely to save memory - each supported CPU adds approximately eight kilobytes to the kernel image. +config XIP_KERNEL + bool "Kernel Execute-In-Place from ROM" + default n + +config XIP_VIRT_ADDR + hex "Kernel .text virtual address" + depends on XIP_KERNEL + default 0 + config PREEMPT bool "Preemptible Kernel" help diff -u -rN -p linux-2.6.10/arch/mips/Makefile linux-2.6.10-rbtx49/arch/mips/Makefile --- linux-2.6.10/arch/mips/Makefile 2004-12-25 06:33:49.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/Makefile 2005-04-22 14:46:18.000000000 +0900 @@ -633,6 +633,15 @@ core-$(CONFIG_TOSHIBA_RBTX4927) += arch/ core-$(CONFIG_TOSHIBA_RBTX4927) += arch/mips/tx4927/common/ load-$(CONFIG_TOSHIBA_RBTX4927) += 0xffffffff80020000 +# +# TX-RISC boards +# +libs-$(CONFIG_TX_BOARDS) += arch/mips/tx-boards/generic/ +cflags-$(CONFIG_TX_BOARDS) += -Iinclude/asm-mips/mach-tx +load-$(CONFIG_TX_BOARDS) += 0xffffffff80100000 +core-$(CONFIG_TX_RBTX4927) += arch/mips/tx-boards/rbtx4927/ +core-$(CONFIG_TX_RBTX4938) += arch/mips/tx-boards/rbtx4938/ + cflags-y += -Iinclude/asm-mips/mach-generic drivers-$(CONFIG_PCI) += arch/mips/pci/ @@ -659,11 +668,20 @@ OBJCOPYFLAGS += --remove-section=.regin # none has been choosen above. # +ifeq ($(CONFIG_XIP_KERNEL),y) +CPPFLAGS_vmlinux.lds := \ + $(CFLAGS) \ + -D"LOADADDR=$(CONFIG_XIP_VIRT_ADDR)" \ + -D"DATAADDR=$(load-y)" \ + -D"JIFFIES=$(JIFFIES)" \ + -D"DATAOFFSET=$(if $(dataoffset-y),$(dataoffset-y),0)" +else CPPFLAGS_vmlinux.lds := \ $(CFLAGS) \ -D"LOADADDR=$(load-y)" \ -D"JIFFIES=$(JIFFIES)" \ -D"DATAOFFSET=$(if $(dataoffset-y),$(dataoffset-y),0)" +endif head-y := arch/mips/kernel/head.o arch/mips/kernel/init_task.o @@ -707,7 +725,11 @@ ifdef CONFIG_SNI_RM200_PCI all: vmlinux.ecoff endif -vmlinux.ecoff vmlinux.rm200: $(vmlinux-32) +ifdef CONFIG_TX_BOARDS +all: vmlinux.elf +endif + +vmlinux.ecoff vmlinux.rm200 vmlinux.elf xipImage: $(vmlinux-32) +@$(call makeboot,$@) vmlinux.srec: $(vmlinux-32) @@ -744,36 +766,16 @@ define filechk_gen-asm-offset.h echo "#endif /* _ASM_OFFSET_H */" ) endef -define filechk_gen-asm-reg.h - (set -e; \ - echo "#ifndef _ASM_REG_H"; \ - echo "#define _ASM_REG_H"; \ - echo "/*"; \ - echo " * DO NOT MODIFY."; \ - echo " *"; \ - echo " * This file was generated by arch/$(ARCH)/Makefile"; \ - echo " *"; \ - echo " */"; \ - echo ""; \ - sed -ne "/^@@@/s///p"; \ - echo "#endif /* _ASM_REG_H */" ) -endef - -prepare: include/asm-$(ARCH)/offset.h \ - include/asm-$(ARCH)/reg.h +prepare: include/asm-$(ARCH)/offset.h arch/$(ARCH)/kernel/offset.s: include/asm include/linux/version.h \ include/config/MARKER include/asm-$(ARCH)/offset.h: arch/$(ARCH)/kernel/offset.s $(call filechk,gen-asm-offset.h) -include/asm-$(ARCH)/reg.h: arch/$(ARCH)/kernel/reg.s - $(call filechk,gen-asm-reg.h) CLEAN_FILES += include/asm-$(ARCH)/offset.h.tmp \ include/asm-$(ARCH)/offset.h \ - include/asm-$(ARCH)/reg.h.tmp \ - include/asm-$(ARCH)/reg.h \ vmlinux.32 \ vmlinux.64 \ vmlinux.ecoff diff -u -rN -p linux-2.6.10/arch/mips/boot/Makefile linux-2.6.10-rbtx49/arch/mips/boot/Makefile --- linux-2.6.10/arch/mips/boot/Makefile 2004-12-25 06:35:24.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/boot/Makefile 2005-04-22 14:46:19.000000000 +0900 @@ -33,17 +33,35 @@ vmlinux.ecoff: $(obj)/elf2ecoff $(VMLINU $(obj)/elf2ecoff: $(obj)/elf2ecoff.c $(HOSTCC) -o $@ $^ +vmlinux.elf: $(VMLINUX) + $(STRIP) -o $(obj)/vmlinux.elf $(VMLINUX) + vmlinux.srec: $(VMLINUX) $(OBJCOPY) -S -O srec $(strip-flags) $(VMLINUX) $(obj)/vmlinux.srec $(obj)/addinitrd: $(obj)/addinitrd.c $(HOSTCC) -o $@ $^ +# +# Create XIP image +# +ifeq ($(CONFIG_XIP_KERNEL),y) +xipImage: $(VMLINUX) + $(OBJCOPY) -O binary -R .data $(strip-flags) vmlinux vmlinux-text.bin + $(OBJCOPY) -O binary -j .data vmlinux vmlinux-data.bin + cat vmlinux-text.bin vmlinux-data.bin > $@ + $(RM) -f vmlinux-text.bin vmlinux-data.bin + @echo ' kernel: $@ is ready' +endif archhelp: @echo '* vmlinux.ecoff - ECOFF boot image' + @echo '* vmlinux.elf - ELF boot image' @echo '* vmlinux.srec - SREC boot image' + @echo '* xipImage - XIP image' clean-files += addinitrd \ elf2ecoff \ vmlinux.ecoff \ - vmlinux.srec + vmlinux.elf \ + vmlinux.srec \ + xipImage diff -u -rN -p linux-2.6.10/arch/mips/configs/tx-r4k-be_defconfig linux-2.6.10-rbtx49/arch/mips/configs/tx-r4k-be_defconfig --- linux-2.6.10/arch/mips/configs/tx-r4k-be_defconfig 1970-01-01 09:00:00.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/configs/tx-r4k-be_defconfig 2005-04-22 14:46:19.000000000 +0900 @@ -0,0 +1,1501 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.10-TSB20041227 +# Thu Feb 10 15:42:57 2005 +# +CONFIG_MIPS=y +# CONFIG_MIPS64 is not set +# CONFIG_64BIT is not set +CONFIG_MIPS32=y + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_CLEAN_COMPILE=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_LOCK_KERNEL=y + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_HOTPLUG=y +CONFIG_KOBJECT_UEVENT=y +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_EMBEDDED=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_FUTEX=y +CONFIG_EPOLL=y +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SHMEM=y +CONFIG_CC_ALIGN_FUNCTIONS=0 +CONFIG_CC_ALIGN_LABELS=0 +CONFIG_CC_ALIGN_LOOPS=0 +CONFIG_CC_ALIGN_JUMPS=0 +# CONFIG_TINY_SHMEM is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_OBSOLETE_MODPARM=y +CONFIG_MODVERSIONS=y +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Machine selection +# +# CONFIG_MACH_JAZZ is not set +# CONFIG_MACH_VR41XX is not set +# CONFIG_TOSHIBA_JMR3927 is not set +# CONFIG_MIPS_COBALT is not set +# CONFIG_MACH_DECSTATION is not set +# CONFIG_MIPS_EV64120 is not set +# CONFIG_MIPS_EV96100 is not set +# CONFIG_MIPS_IVR is not set +# CONFIG_LASAT is not set +# CONFIG_MIPS_ITE8172 is not set +# CONFIG_MIPS_ATLAS is not set +# CONFIG_MIPS_MALTA is not set +# CONFIG_MIPS_SEAD is not set +# CONFIG_MOMENCO_OCELOT is not set +# CONFIG_MOMENCO_OCELOT_G is not set +# CONFIG_MOMENCO_OCELOT_C is not set +# CONFIG_MOMENCO_OCELOT_3 is not set +# CONFIG_MOMENCO_JAGUAR_ATX is not set +# CONFIG_PMC_YOSEMITE is not set +# CONFIG_DDB5074 is not set +# CONFIG_DDB5476 is not set +# CONFIG_DDB5477 is not set +# CONFIG_NEC_OSPREY is not set +# CONFIG_SGI_IP22 is not set +# CONFIG_SOC_AU1X00 is not set +# CONFIG_SIBYTE_SB1xxx_SOC is not set +# CONFIG_SNI_RM200_PCI is not set +# CONFIG_TOSHIBA_RBTX4927 is not set +CONFIG_TX_RBTX4927=y +CONFIG_TX_RBTX4938=y +CONFIG_TX_BOARDS=y +# CONFIG_PICMG_PCI_BACKPLANE_DEFAULT is not set +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_HAVE_DEC_LOCK=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_EARLY_PRINTK=y +# CONFIG_CPU_LITTLE_ENDIAN is not set +CONFIG_IRQ_CPU=y +CONFIG_SWAP_IO_SPACE=y +CONFIG_BOOT_ELF32=y +CONFIG_MIPS_L1_CACHE_SHIFT=5 +CONFIG_HEARTBEAT=y + +# +# CPU selection +# +# CONFIG_CPU_MIPS32 is not set +# CONFIG_CPU_MIPS64 is not set +# CONFIG_CPU_R3000 is not set +# CONFIG_CPU_TX39XX is not set +# CONFIG_CPU_VR41XX is not set +# CONFIG_CPU_R4300 is not set +# CONFIG_CPU_R4X00 is not set +CONFIG_CPU_TX49XX=y +# CONFIG_CPU_R5000 is not set +# CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R6000 is not set +# CONFIG_CPU_NEVADA is not set +# CONFIG_CPU_R8000 is not set +# CONFIG_CPU_R10000 is not set +# CONFIG_CPU_RM7000 is not set +# CONFIG_CPU_RM9000 is not set +# CONFIG_CPU_SB1 is not set +CONFIG_PAGE_SIZE_4KB=y +# CONFIG_PAGE_SIZE_8KB is not set +# CONFIG_PAGE_SIZE_16KB is not set +# CONFIG_PAGE_SIZE_64KB is not set +# CONFIG_CPU_ADVANCED is not set +CONFIG_CPU_HAS_LLSC=y +CONFIG_CPU_HAS_LLDSCD=y +CONFIG_CPU_HAS_SYNC=y +# CONFIG_XIP_KERNEL is not set +CONFIG_PREEMPT=y + +# +# Bus options (PCI, PCMCIA, EISA, ISA, TC) +# +CONFIG_HW_HAS_PCI=y +CONFIG_PCI=y +# CONFIG_PCI_LEGACY_PROC is not set +CONFIG_PCI_NAMES=y +CONFIG_ISA=y +CONFIG_MMU=y + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# PC-card bridges +# +CONFIG_PCMCIA_PROBE=y + +# +# PCI Hotplug Support +# +# CONFIG_HOTPLUG_PCI is not set + +# +# Executable file formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +CONFIG_TRAD_SIGNALS=y + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_CONCAT is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +# CONFIG_MTD_BLOCK is not set +CONFIG_MTD_BLOCK_RO=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_AMDSTD_RETRY=0 +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +CONFIG_MTD_COMPLEX_MAPPINGS=y +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_CSTM_MIPS_IXX is not set +CONFIG_MTD_TXBOARD=y +# CONFIG_MTD_PCI is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLKMTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set + +# +# NAND Flash Device Drivers +# +CONFIG_MTD_NAND=m +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +CONFIG_MTD_NAND_IDS=m +CONFIG_MTD_NAND_TXX9NDFMC=m +# CONFIG_MTD_NAND_DISKONCHIP is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# +# CONFIG_PNP is not set + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_DEV_XD is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_LBD is not set +# CONFIG_CDROM_PKTCDVD is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +CONFIG_SCSI=y +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=m +# CONFIG_BLK_DEV_SR_VENDOR is not set +# CONFIG_CHR_DEV_SG is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +CONFIG_SCSI_CONSTANTS=y +# CONFIG_SCSI_LOGGING is not set + +# +# SCSI Transport Attributes +# +CONFIG_SCSI_SPI_ATTRS=y +# CONFIG_SCSI_FC_ATTRS is not set + +# +# SCSI low-level drivers +# +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_7000FASST is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AHA152X is not set +# CONFIG_SCSI_AHA1542 is not set +# CONFIG_SCSI_AACRAID is not set +CONFIG_SCSI_AIC7XXX=y +CONFIG_AIC7XXX_CMDS_PER_DEVICE=32 +CONFIG_AIC7XXX_RESET_DELAY_MS=15000 +# CONFIG_AIC7XXX_DEBUG_ENABLE is not set +CONFIG_AIC7XXX_DEBUG_MASK=0 +# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_IN2000 is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_SCSI_SATA is not set +# CONFIG_SCSI_BUSLOGIC is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_DTC3280 is not set +# CONFIG_SCSI_EATA is not set +# CONFIG_SCSI_EATA_PIO is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GDTH is not set +# CONFIG_SCSI_GENERIC_NCR5380 is not set +# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_NCR53C406A is not set +CONFIG_SCSI_SYM53C8XX_2=y +CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1 +CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16 +CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64 +# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_PAS16 is not set +# CONFIG_SCSI_PSI240I is not set +# CONFIG_SCSI_QLOGIC_FAS is not set +# CONFIG_SCSI_QLOGIC_ISP is not set +# CONFIG_SCSI_QLOGIC_FC is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +CONFIG_SCSI_QLA2XXX=y +# CONFIG_SCSI_QLA21XX is not set +# CONFIG_SCSI_QLA22XX is not set +# CONFIG_SCSI_QLA2300 is not set +# CONFIG_SCSI_QLA2322 is not set +# CONFIG_SCSI_QLA6312 is not set +# CONFIG_SCSI_QLA6322 is not set +# CONFIG_SCSI_SYM53C416 is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_T128 is not set +# CONFIG_SCSI_U14_34F is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set + +# +# Old CD-ROM drivers (not SCSI, not IDE) +# +# CONFIG_CD_NO_IDESCSI is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# +CONFIG_IEEE1394=m + +# +# Subsystem Options +# +# CONFIG_IEEE1394_VERBOSEDEBUG is not set +# CONFIG_IEEE1394_OUI_DB is not set +CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y +CONFIG_IEEE1394_CONFIG_ROM_IP1394=y + +# +# Device Drivers +# +# CONFIG_IEEE1394_PCILYNX is not set +CONFIG_IEEE1394_OHCI1394=m + +# +# Protocol Drivers +# +# CONFIG_IEEE1394_VIDEO1394 is not set +CONFIG_IEEE1394_SBP2=m +# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set +CONFIG_IEEE1394_ETH1394=m +# CONFIG_IEEE1394_DV1394 is not set +CONFIG_IEEE1394_RAWIO=m +# CONFIG_IEEE1394_CMP is not set + +# +# I2O device support +# +# CONFIG_I2O is not set + +# +# Networking support +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +# CONFIG_NETLINK_DEV is not set +CONFIG_UNIX=y +CONFIG_NET_KEY=m +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +CONFIG_INET_AH=m +CONFIG_INET_ESP=m +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_IP_TCPDIAG=m +# CONFIG_IP_TCPDIAG_IPV6 is not set + +# +# IP: Virtual Server Configuration +# +# CONFIG_IP_VS is not set +# CONFIG_IPV6 is not set +CONFIG_NETFILTER=y +# CONFIG_NETFILTER_DEBUG is not set + +# +# IP: Netfilter Configuration +# +CONFIG_IP_NF_CONNTRACK=m +# CONFIG_IP_NF_CT_ACCT is not set +CONFIG_IP_NF_CONNTRACK_MARK=y +# CONFIG_IP_NF_CT_PROTO_SCTP is not set +CONFIG_IP_NF_FTP=m +CONFIG_IP_NF_IRC=m +CONFIG_IP_NF_TFTP=m +CONFIG_IP_NF_AMANDA=m +CONFIG_IP_NF_QUEUE=m +CONFIG_IP_NF_IPTABLES=m +CONFIG_IP_NF_MATCH_LIMIT=m +CONFIG_IP_NF_MATCH_IPRANGE=m +CONFIG_IP_NF_MATCH_MAC=m +CONFIG_IP_NF_MATCH_PKTTYPE=m +CONFIG_IP_NF_MATCH_MARK=m +CONFIG_IP_NF_MATCH_MULTIPORT=m +CONFIG_IP_NF_MATCH_TOS=m +CONFIG_IP_NF_MATCH_RECENT=m +CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_DSCP=m +CONFIG_IP_NF_MATCH_AH_ESP=m +CONFIG_IP_NF_MATCH_LENGTH=m +CONFIG_IP_NF_MATCH_TTL=m +CONFIG_IP_NF_MATCH_TCPMSS=m +CONFIG_IP_NF_MATCH_HELPER=m +CONFIG_IP_NF_MATCH_STATE=m +CONFIG_IP_NF_MATCH_CONNTRACK=m +CONFIG_IP_NF_MATCH_OWNER=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m +CONFIG_IP_NF_MATCH_REALM=m +CONFIG_IP_NF_MATCH_SCTP=m +CONFIG_IP_NF_MATCH_COMMENT=m +CONFIG_IP_NF_MATCH_CONNMARK=m +CONFIG_IP_NF_MATCH_HASHLIMIT=m +CONFIG_IP_NF_FILTER=m +CONFIG_IP_NF_TARGET_REJECT=m +CONFIG_IP_NF_TARGET_LOG=m +CONFIG_IP_NF_TARGET_ULOG=m +CONFIG_IP_NF_TARGET_TCPMSS=m +CONFIG_IP_NF_NAT=m +CONFIG_IP_NF_NAT_NEEDED=y +CONFIG_IP_NF_TARGET_MASQUERADE=m +CONFIG_IP_NF_TARGET_REDIRECT=m +CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_SAME=m +CONFIG_IP_NF_NAT_LOCAL=y +CONFIG_IP_NF_NAT_SNMP_BASIC=m +CONFIG_IP_NF_NAT_IRC=m +CONFIG_IP_NF_NAT_FTP=m +CONFIG_IP_NF_NAT_TFTP=m +CONFIG_IP_NF_NAT_AMANDA=m +CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_TOS=m +CONFIG_IP_NF_TARGET_ECN=m +CONFIG_IP_NF_TARGET_DSCP=m +CONFIG_IP_NF_TARGET_MARK=m +CONFIG_IP_NF_TARGET_CLASSIFY=m +CONFIG_IP_NF_TARGET_CONNMARK=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m +CONFIG_IP_NF_RAW=m +CONFIG_IP_NF_TARGET_NOTRACK=m +CONFIG_IP_NF_ARPTABLES=m +CONFIG_IP_NF_ARPFILTER=m +CONFIG_IP_NF_ARP_MANGLE=m +CONFIG_IP_NF_COMPAT_IPCHAINS=m +# CONFIG_IP_NF_COMPAT_IPFWADM is not set +CONFIG_XFRM=y +CONFIG_XFRM_USER=m + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set +CONFIG_NET_CLS_ROUTE=y + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# ARCnet devices +# +# CONFIG_ARCNET is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_LANCE is not set +# CONFIG_NET_VENDOR_SMC is not set +# CONFIG_NET_VENDOR_RACAL is not set + +# +# Tulip family network device support +# +# CONFIG_NET_TULIP is not set +# CONFIG_AT1700 is not set +# CONFIG_DEPCA is not set +# CONFIG_HP100 is not set +# CONFIG_NET_ISA is not set +CONFIG_NET_PCI=y +# CONFIG_PCNET32 is not set +# CONFIG_AMD8111_ETH is not set +# CONFIG_ADAPTEC_STARFIRE is not set +# CONFIG_AC3200 is not set +# CONFIG_APRICOT is not set +# CONFIG_B44 is not set +# CONFIG_FORCEDETH is not set +# CONFIG_CS89x0 is not set +CONFIG_TC35815_1=y +# CONFIG_DGRS is not set +# CONFIG_EEPRO100 is not set +# CONFIG_E100 is not set +# CONFIG_FEALNX is not set +# CONFIG_NATSEMI is not set +# CONFIG_NE2K_PCI is not set +# CONFIG_8139CP is not set +CONFIG_8139TOO=y +# CONFIG_8139TOO_PIO is not set +# CONFIG_8139TOO_TUNE_TWISTER is not set +# CONFIG_8139TOO_8129 is not set +# CONFIG_8139_OLD_RX_RESET is not set +# CONFIG_SIS900 is not set +# CONFIG_EPIC100 is not set +# CONFIG_SUNDANCE is not set +# CONFIG_TLAN is not set +# CONFIG_VIA_RHINE is not set +# CONFIG_LAN_SAA9730 is not set +# CONFIG_NET_POCKET is not set +CONFIG_TXBOARD_OBNE_NET=y + +# +# Ethernet (1000 Mbit) +# +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SK98LIN is not set +# CONFIG_VIA_VELOCITY is not set +# CONFIG_TIGON3 is not set + +# +# Ethernet (10000 Mbit) +# +# CONFIG_IXGB is not set +# CONFIG_S2IO is not set + +# +# Token Ring devices +# +# CONFIG_TR is not set + +# +# Wireless LAN (non-hamradio) +# +CONFIG_NET_RADIO=y + +# +# Obsolete Wireless cards support (pre-802.11) +# +# CONFIG_STRIP is not set +# CONFIG_ARLAN is not set +# CONFIG_WAVELAN is not set + +# +# Wireless 802.11b ISA/PCI cards support +# +# CONFIG_AIRO is not set +CONFIG_HERMES=m +# CONFIG_PLX_HERMES is not set +# CONFIG_TMD_HERMES is not set +CONFIG_PCI_HERMES=m +# CONFIG_ATMEL is not set + +# +# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support +# +# CONFIG_PRISM54 is not set +CONFIG_NET_WIRELESS=y + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NET_FC is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=m +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +CONFIG_INPUT_EVDEV=m +CONFIG_INPUT_EVBUG=m + +# +# Input I/O drivers +# +# CONFIG_GAMEPORT is not set +CONFIG_SOUND_GAMEPORT=y +CONFIG_SERIO=y +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_SERPORT is not set +# CONFIG_SERIO_CT82C710 is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_RAW is not set + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +CONFIG_KEYBOARD_ATKBD=y +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +CONFIG_INPUT_MOUSE=y +CONFIG_MOUSE_PS2=y +# CONFIG_MOUSE_SERIAL is not set +# CONFIG_MOUSE_INPORT is not set +# CONFIG_MOUSE_LOGIBM is not set +# CONFIG_MOUSE_PC110PAD is not set +# CONFIG_MOUSE_VSXXXAA is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +CONFIG_SERIAL_NONSTANDARD=y +# CONFIG_COMPUTONE is not set +# CONFIG_ROCKETPORT is not set +# CONFIG_CYCLADES is not set +# CONFIG_DIGIEPCA is not set +# CONFIG_DIGI is not set +# CONFIG_ESPSERIAL is not set +# CONFIG_MOXA_INTELLIO is not set +# CONFIG_MOXA_SMARTIO is not set +# CONFIG_ISI is not set +# CONFIG_SYNCLINK is not set +# CONFIG_SYNCLINKMP is not set +# CONFIG_N_HDLC is not set +# CONFIG_RISCOM8 is not set +# CONFIG_SPECIALIX is not set +# CONFIG_SX is not set +# CONFIG_RIO is not set +# CONFIG_STALDRV is not set +# CONFIG_SERIAL_TX3912 is not set +# CONFIG_AU1000_UART is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_TXX9=y +CONFIG_SERIAL_TXX9_CONSOLE=y +CONFIG_SERIAL_TXX9_STDSERIAL=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set + +# +# ISA-based Watchdog Cards +# +# CONFIG_PCWATCHDOG is not set +# CONFIG_MIXCOMWD is not set +# CONFIG_WDT is not set + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_RTC is not set +CONFIG_GEN_RTC=y +CONFIG_GEN_RTC_X=y +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_RAW_DRIVER is not set + +# +# I2C support +# +CONFIG_I2C=y +CONFIG_I2C_CHARDEV=m + +# +# I2C Algorithms +# +CONFIG_I2C_ALGOBIT=y +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_ELEKTOR is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_I810 is not set +# CONFIG_I2C_ISA is not set +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_PIIX4 is not set +# CONFIG_I2C_PROSAVAGE is not set +# CONFIG_I2C_SAVAGE4 is not set +# CONFIG_SCx200_ACB is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set +# CONFIG_I2C_VOODOO3 is not set +# CONFIG_I2C_PCA_ISA is not set + +# +# Hardware Sensors Chip support +# +# CONFIG_I2C_SENSOR is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_FSCHER is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_VIA686A is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83627HF is not set + +# +# Other I2C Chip support +# +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_RTC8564 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Misc devices +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +# CONFIG_MDA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +CONFIG_SOUND=m + +# +# Advanced Linux Sound Architecture +# +CONFIG_SND=m +CONFIG_SND_TIMER=m +CONFIG_SND_PCM=m +CONFIG_SND_HWDEP=m +CONFIG_SND_RAWMIDI=m +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=m +CONFIG_SND_PCM_OSS=m +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set + +# +# Generic devices +# +CONFIG_SND_MPU401_UART=m +CONFIG_SND_OPL3_LIB=m +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set + +# +# ISA devices +# +# CONFIG_SND_AD1848 is not set +# CONFIG_SND_CS4231 is not set +# CONFIG_SND_CS4232 is not set +# CONFIG_SND_CS4236 is not set +# CONFIG_SND_ES1688 is not set +# CONFIG_SND_ES18XX is not set +# CONFIG_SND_GUSCLASSIC is not set +# CONFIG_SND_GUSEXTREME is not set +# CONFIG_SND_GUSMAX is not set +# CONFIG_SND_INTERWAVE is not set +# CONFIG_SND_INTERWAVE_STB is not set +# CONFIG_SND_OPTI92X_AD1848 is not set +# CONFIG_SND_OPTI92X_CS4231 is not set +# CONFIG_SND_OPTI93X is not set +# CONFIG_SND_SB8 is not set +# CONFIG_SND_SB16 is not set +# CONFIG_SND_SBAWE is not set +# CONFIG_SND_WAVEFRONT is not set +# CONFIG_SND_CMI8330 is not set +# CONFIG_SND_OPL3SA2 is not set +# CONFIG_SND_SGALAXY is not set +# CONFIG_SND_SSCAPE is not set + +# +# PCI devices +# +CONFIG_SND_AC97_CODEC=m +# CONFIG_SND_ALI5451 is not set +# CONFIG_SND_ATIIXP is not set +# CONFIG_SND_ATIIXP_MODEM is not set +# CONFIG_SND_AU8810 is not set +# CONFIG_SND_AU8820 is not set +# CONFIG_SND_AU8830 is not set +# CONFIG_SND_AZT3328 is not set +# CONFIG_SND_BT87X is not set +# CONFIG_SND_CS46XX is not set +# CONFIG_SND_CS4281 is not set +# CONFIG_SND_EMU10K1 is not set +# CONFIG_SND_KORG1212 is not set +# CONFIG_SND_MIXART is not set +# CONFIG_SND_NM256 is not set +# CONFIG_SND_RME32 is not set +# CONFIG_SND_RME96 is not set +# CONFIG_SND_RME9652 is not set +# CONFIG_SND_HDSP is not set +# CONFIG_SND_TRIDENT is not set +CONFIG_SND_YMFPCI=m +# CONFIG_SND_ALS4000 is not set +CONFIG_SND_CMIPCI=m +# CONFIG_SND_ENS1370 is not set +# CONFIG_SND_ENS1371 is not set +# CONFIG_SND_ES1938 is not set +# CONFIG_SND_ES1968 is not set +# CONFIG_SND_MAESTRO3 is not set +# CONFIG_SND_FM801 is not set +# CONFIG_SND_ICE1712 is not set +# CONFIG_SND_ICE1724 is not set +# CONFIG_SND_INTEL8X0 is not set +# CONFIG_SND_INTEL8X0M is not set +# CONFIG_SND_SONICVIBES is not set +# CONFIG_SND_VIA82XX is not set +# CONFIG_SND_VX222 is not set + +# +# USB devices +# +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_USX2Y is not set + +# +# ALSA MIPS devices +# +# CONFIG_SND_TX49XX is not set + +# +# Open Sound System +# +# CONFIG_SOUND_PRIME is not set + +# +# USB support +# +CONFIG_USB=m +# CONFIG_USB_DEBUG is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_BANDWIDTH is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y + +# +# USB Host Controller Drivers +# +CONFIG_USB_EHCI_HCD=m +# CONFIG_USB_EHCI_SPLIT_ISO is not set +# CONFIG_USB_EHCI_ROOT_HUB_TT is not set +CONFIG_USB_OHCI_HCD=m +CONFIG_USB_UHCI_HCD=m +# CONFIG_USB_SL811_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_AUDIO is not set +# CONFIG_USB_BLUETOOTH_TTY is not set +# CONFIG_USB_MIDI is not set +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=m +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_RW_DETECT is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_HP8200e is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=m +CONFIG_USB_HIDINPUT=y +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +# CONFIG_USB_AIPTEK is not set +# CONFIG_USB_WACOM is not set +# CONFIG_USB_KBTAB is not set +# CONFIG_USB_POWERMATE is not set +# CONFIG_USB_MTOUCH is not set +# CONFIG_USB_EGALAX is not set +# CONFIG_USB_XPAD is not set +# CONFIG_USB_ATI_REMOTE is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +# CONFIG_USB_HPUSBSCSI is not set + +# +# USB Multimedia devices +# +# CONFIG_USB_DABUSB is not set + +# +# Video4Linux support is needed for USB Multimedia device support +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +CONFIG_USB_USBNET=m + +# +# USB Host-to-Host Cables +# +# CONFIG_USB_ALI_M5632 is not set +# CONFIG_USB_AN2720 is not set +# CONFIG_USB_BELKIN is not set +# CONFIG_USB_GENESYS is not set +# CONFIG_USB_NET1080 is not set +# CONFIG_USB_PL2301 is not set +# CONFIG_USB_KC2190 is not set + +# +# Intelligent USB Devices/Gadgets +# +# CONFIG_USB_ARMLINUX is not set +# CONFIG_USB_EPSON2888 is not set +# CONFIG_USB_ZAURUS is not set +CONFIG_USB_CDCETHER=y + +# +# USB Network Adapters +# +# CONFIG_USB_AX8817X is not set + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +CONFIG_USB_SERIAL=m +CONFIG_USB_SERIAL_GENERIC=y +# CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_WHITEHEAT is not set +# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set +# CONFIG_USB_SERIAL_CYPRESS_M8 is not set +# CONFIG_USB_SERIAL_EMPEG is not set +# CONFIG_USB_SERIAL_FTDI_SIO is not set +# CONFIG_USB_SERIAL_VISOR is not set +# CONFIG_USB_SERIAL_IPAQ is not set +# CONFIG_USB_SERIAL_IR is not set +# CONFIG_USB_SERIAL_EDGEPORT is not set +# CONFIG_USB_SERIAL_EDGEPORT_TI is not set +# CONFIG_USB_SERIAL_IPW is not set +# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set +# CONFIG_USB_SERIAL_KEYSPAN is not set +# CONFIG_USB_SERIAL_KLSI is not set +# CONFIG_USB_SERIAL_KOBIL_SCT is not set +# CONFIG_USB_SERIAL_MCT_U232 is not set +CONFIG_USB_SERIAL_PL2303=m +# CONFIG_USB_SERIAL_SAFE is not set +# CONFIG_USB_SERIAL_CYBERJACK is not set +# CONFIG_USB_SERIAL_XIRCOM is not set +# CONFIG_USB_SERIAL_OMNINET is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_TIGL is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGETKIT is not set +# CONFIG_USB_PHIDGETSERVO is not set +# CONFIG_USB_TEST is not set + +# +# USB ATM/DSL drivers +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=m +# CONFIG_USB_GADGET_DEBUG_FILES is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +CONFIG_USB_GADGET_GOKU=y +CONFIG_USB_GOKU=m +# CONFIG_USB_GADGET_SA1100 is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +CONFIG_USB_ZERO=m +CONFIG_USB_ETH=m +CONFIG_USB_ETH_RNDIS=y +# CONFIG_USB_GADGETFS is not set +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_FS_XATTR is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_XFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set + +# +# CD-ROM/DVD Filesystems +# +CONFIG_ISO9660_FS=y +CONFIG_JOLIET=y +# CONFIG_ZISOFS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=m +# CONFIG_MSDOS_FS is not set +CONFIG_VFAT_FS=m +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_SYSFS=y +# CONFIG_DEVFS_FS is not set +# CONFIG_DEVPTS_FS_XATTR is not set +CONFIG_TMPFS=y +# CONFIG_TMPFS_XATTR is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_PRAMFS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_NAND=y +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_CRAMFS_EXPAND_SIZE is not set +# CONFIG_CRAMFS_LINEAR is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +# CONFIG_EXPORTFS is not set +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=m +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +CONFIG_NLS_CODEPAGE_932=m +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=m +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set + +# +# Kernel hacking +# +CONFIG_DEBUG_KERNEL=y +CONFIG_MAGIC_SYSRQ=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_INFO is not set +CONFIG_CROSSCOMPILE=y +CONFIG_CMDLINE="" +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_KGDB is not set +# CONFIG_RUNTIME_DEBUG is not set +# CONFIG_MIPS_UNCACHED is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +CONFIG_CRYPTO=y +CONFIG_CRYPTO_HMAC=y +CONFIG_CRYPTO_NULL=m +CONFIG_CRYPTO_MD4=m +CONFIG_CRYPTO_MD5=m +CONFIG_CRYPTO_SHA1=m +CONFIG_CRYPTO_SHA256=m +CONFIG_CRYPTO_SHA512=m +CONFIG_CRYPTO_WP512=m +CONFIG_CRYPTO_DES=m +CONFIG_CRYPTO_BLOWFISH=m +CONFIG_CRYPTO_TWOFISH=m +CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_AES=m +CONFIG_CRYPTO_CAST5=m +CONFIG_CRYPTO_CAST6=m +CONFIG_CRYPTO_TEA=m +CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_KHAZAD=m +CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_DEFLATE=m +CONFIG_CRYPTO_MICHAEL_MIC=m +CONFIG_CRYPTO_CRC32C=m +CONFIG_CRYPTO_TEST=m + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +CONFIG_CRC32=y +CONFIG_LIBCRC32C=m +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_IRQ_PROBE=y diff -u -rN -p linux-2.6.10/arch/mips/configs/tx-r4k_defconfig linux-2.6.10-rbtx49/arch/mips/configs/tx-r4k_defconfig --- linux-2.6.10/arch/mips/configs/tx-r4k_defconfig 1970-01-01 09:00:00.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/configs/tx-r4k_defconfig 2005-04-22 14:46:19.000000000 +0900 @@ -0,0 +1,1501 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.10-TSB20041227 +# Thu Feb 10 15:42:43 2005 +# +CONFIG_MIPS=y +# CONFIG_MIPS64 is not set +# CONFIG_64BIT is not set +CONFIG_MIPS32=y + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_CLEAN_COMPILE=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_LOCK_KERNEL=y + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +CONFIG_SYSCTL=y +# CONFIG_AUDIT is not set +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_HOTPLUG=y +CONFIG_KOBJECT_UEVENT=y +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_EMBEDDED=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_FUTEX=y +CONFIG_EPOLL=y +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SHMEM=y +CONFIG_CC_ALIGN_FUNCTIONS=0 +CONFIG_CC_ALIGN_LABELS=0 +CONFIG_CC_ALIGN_LOOPS=0 +CONFIG_CC_ALIGN_JUMPS=0 +# CONFIG_TINY_SHMEM is not set + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_OBSOLETE_MODPARM=y +CONFIG_MODVERSIONS=y +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Machine selection +# +# CONFIG_MACH_JAZZ is not set +# CONFIG_MACH_VR41XX is not set +# CONFIG_TOSHIBA_JMR3927 is not set +# CONFIG_MIPS_COBALT is not set +# CONFIG_MACH_DECSTATION is not set +# CONFIG_MIPS_EV64120 is not set +# CONFIG_MIPS_EV96100 is not set +# CONFIG_MIPS_IVR is not set +# CONFIG_LASAT is not set +# CONFIG_MIPS_ITE8172 is not set +# CONFIG_MIPS_ATLAS is not set +# CONFIG_MIPS_MALTA is not set +# CONFIG_MIPS_SEAD is not set +# CONFIG_MOMENCO_OCELOT is not set +# CONFIG_MOMENCO_OCELOT_G is not set +# CONFIG_MOMENCO_OCELOT_C is not set +# CONFIG_MOMENCO_OCELOT_3 is not set +# CONFIG_MOMENCO_JAGUAR_ATX is not set +# CONFIG_PMC_YOSEMITE is not set +# CONFIG_DDB5074 is not set +# CONFIG_DDB5476 is not set +# CONFIG_DDB5477 is not set +# CONFIG_NEC_OSPREY is not set +# CONFIG_SGI_IP22 is not set +# CONFIG_SOC_AU1X00 is not set +# CONFIG_SIBYTE_SB1xxx_SOC is not set +# CONFIG_SNI_RM200_PCI is not set +# CONFIG_TOSHIBA_RBTX4927 is not set +CONFIG_TX_RBTX4927=y +CONFIG_TX_RBTX4938=y +CONFIG_TX_BOARDS=y +# CONFIG_PICMG_PCI_BACKPLANE_DEFAULT is not set +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_HAVE_DEC_LOCK=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_EARLY_PRINTK=y +CONFIG_CPU_LITTLE_ENDIAN=y +CONFIG_IRQ_CPU=y +CONFIG_SWAP_IO_SPACE=y +CONFIG_BOOT_ELF32=y +CONFIG_MIPS_L1_CACHE_SHIFT=5 +CONFIG_HEARTBEAT=y + +# +# CPU selection +# +# CONFIG_CPU_MIPS32 is not set +# CONFIG_CPU_MIPS64 is not set +# CONFIG_CPU_R3000 is not set +# CONFIG_CPU_TX39XX is not set +# CONFIG_CPU_VR41XX is not set +# CONFIG_CPU_R4300 is not set +# CONFIG_CPU_R4X00 is not set +CONFIG_CPU_TX49XX=y +# CONFIG_CPU_R5000 is not set +# CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R6000 is not set +# CONFIG_CPU_NEVADA is not set +# CONFIG_CPU_R8000 is not set +# CONFIG_CPU_R10000 is not set +# CONFIG_CPU_RM7000 is not set +# CONFIG_CPU_RM9000 is not set +# CONFIG_CPU_SB1 is not set +CONFIG_PAGE_SIZE_4KB=y +# CONFIG_PAGE_SIZE_8KB is not set +# CONFIG_PAGE_SIZE_16KB is not set +# CONFIG_PAGE_SIZE_64KB is not set +# CONFIG_CPU_ADVANCED is not set +CONFIG_CPU_HAS_LLSC=y +CONFIG_CPU_HAS_LLDSCD=y +CONFIG_CPU_HAS_SYNC=y +# CONFIG_XIP_KERNEL is not set +CONFIG_PREEMPT=y + +# +# Bus options (PCI, PCMCIA, EISA, ISA, TC) +# +CONFIG_HW_HAS_PCI=y +CONFIG_PCI=y +# CONFIG_PCI_LEGACY_PROC is not set +CONFIG_PCI_NAMES=y +CONFIG_ISA=y +CONFIG_MMU=y + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# PC-card bridges +# +CONFIG_PCMCIA_PROBE=y + +# +# PCI Hotplug Support +# +# CONFIG_HOTPLUG_PCI is not set + +# +# Executable file formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_MISC is not set +CONFIG_TRAD_SIGNALS=y + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set + +# +# Memory Technology Devices (MTD) +# +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_CONCAT is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=y +# CONFIG_MTD_BLOCK is not set +CONFIG_MTD_BLOCK_RO=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_AMDSTD_RETRY=0 +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +CONFIG_MTD_COMPLEX_MAPPINGS=y +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_CSTM_MIPS_IXX is not set +CONFIG_MTD_TXBOARD=y +# CONFIG_MTD_PCI is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLKMTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set + +# +# NAND Flash Device Drivers +# +CONFIG_MTD_NAND=m +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +CONFIG_MTD_NAND_IDS=m +CONFIG_MTD_NAND_TXX9NDFMC=m +# CONFIG_MTD_NAND_DISKONCHIP is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# +# CONFIG_PNP is not set + +# +# Block devices +# +# CONFIG_BLK_DEV_FD is not set +# CONFIG_BLK_DEV_XD is not set +# CONFIG_BLK_CPQ_DA is not set +# CONFIG_BLK_CPQ_CISS_DA is not set +# CONFIG_BLK_DEV_DAC960 is not set +# CONFIG_BLK_DEV_UMEM is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_SX8 is not set +# CONFIG_BLK_DEV_UB is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_LBD is not set +# CONFIG_CDROM_PKTCDVD is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y + +# +# ATA/ATAPI/MFM/RLL support +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +CONFIG_SCSI=y +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +CONFIG_BLK_DEV_SR=m +# CONFIG_BLK_DEV_SR_VENDOR is not set +# CONFIG_CHR_DEV_SG is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +CONFIG_SCSI_CONSTANTS=y +# CONFIG_SCSI_LOGGING is not set + +# +# SCSI Transport Attributes +# +CONFIG_SCSI_SPI_ATTRS=y +# CONFIG_SCSI_FC_ATTRS is not set + +# +# SCSI low-level drivers +# +# CONFIG_BLK_DEV_3W_XXXX_RAID is not set +# CONFIG_SCSI_3W_9XXX is not set +# CONFIG_SCSI_7000FASST is not set +# CONFIG_SCSI_ACARD is not set +# CONFIG_SCSI_AHA152X is not set +# CONFIG_SCSI_AHA1542 is not set +# CONFIG_SCSI_AACRAID is not set +CONFIG_SCSI_AIC7XXX=y +CONFIG_AIC7XXX_CMDS_PER_DEVICE=32 +CONFIG_AIC7XXX_RESET_DELAY_MS=15000 +# CONFIG_AIC7XXX_DEBUG_ENABLE is not set +CONFIG_AIC7XXX_DEBUG_MASK=0 +# CONFIG_AIC7XXX_REG_PRETTY_PRINT is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_AIC79XX is not set +# CONFIG_SCSI_DPT_I2O is not set +# CONFIG_SCSI_IN2000 is not set +# CONFIG_MEGARAID_NEWGEN is not set +# CONFIG_MEGARAID_LEGACY is not set +# CONFIG_SCSI_SATA is not set +# CONFIG_SCSI_BUSLOGIC is not set +# CONFIG_SCSI_DMX3191D is not set +# CONFIG_SCSI_DTC3280 is not set +# CONFIG_SCSI_EATA is not set +# CONFIG_SCSI_EATA_PIO is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GDTH is not set +# CONFIG_SCSI_GENERIC_NCR5380 is not set +# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set +# CONFIG_SCSI_IPS is not set +# CONFIG_SCSI_INITIO is not set +# CONFIG_SCSI_INIA100 is not set +# CONFIG_SCSI_NCR53C406A is not set +CONFIG_SCSI_SYM53C8XX_2=y +CONFIG_SCSI_SYM53C8XX_DMA_ADDRESSING_MODE=1 +CONFIG_SCSI_SYM53C8XX_DEFAULT_TAGS=16 +CONFIG_SCSI_SYM53C8XX_MAX_TAGS=64 +# CONFIG_SCSI_SYM53C8XX_IOMAPPED is not set +# CONFIG_SCSI_IPR is not set +# CONFIG_SCSI_PAS16 is not set +# CONFIG_SCSI_PSI240I is not set +# CONFIG_SCSI_QLOGIC_FAS is not set +# CONFIG_SCSI_QLOGIC_ISP is not set +# CONFIG_SCSI_QLOGIC_FC is not set +# CONFIG_SCSI_QLOGIC_1280 is not set +CONFIG_SCSI_QLA2XXX=y +# CONFIG_SCSI_QLA21XX is not set +# CONFIG_SCSI_QLA22XX is not set +# CONFIG_SCSI_QLA2300 is not set +# CONFIG_SCSI_QLA2322 is not set +# CONFIG_SCSI_QLA6312 is not set +# CONFIG_SCSI_QLA6322 is not set +# CONFIG_SCSI_SYM53C416 is not set +# CONFIG_SCSI_DC395x is not set +# CONFIG_SCSI_DC390T is not set +# CONFIG_SCSI_T128 is not set +# CONFIG_SCSI_U14_34F is not set +# CONFIG_SCSI_NSP32 is not set +# CONFIG_SCSI_DEBUG is not set + +# +# Old CD-ROM drivers (not SCSI, not IDE) +# +# CONFIG_CD_NO_IDESCSI is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Fusion MPT device support +# +# CONFIG_FUSION is not set + +# +# IEEE 1394 (FireWire) support +# +CONFIG_IEEE1394=m + +# +# Subsystem Options +# +# CONFIG_IEEE1394_VERBOSEDEBUG is not set +# CONFIG_IEEE1394_OUI_DB is not set +CONFIG_IEEE1394_EXTRA_CONFIG_ROMS=y +CONFIG_IEEE1394_CONFIG_ROM_IP1394=y + +# +# Device Drivers +# +# CONFIG_IEEE1394_PCILYNX is not set +CONFIG_IEEE1394_OHCI1394=m + +# +# Protocol Drivers +# +# CONFIG_IEEE1394_VIDEO1394 is not set +CONFIG_IEEE1394_SBP2=m +# CONFIG_IEEE1394_SBP2_PHYS_DMA is not set +CONFIG_IEEE1394_ETH1394=m +# CONFIG_IEEE1394_DV1394 is not set +CONFIG_IEEE1394_RAWIO=m +# CONFIG_IEEE1394_CMP is not set + +# +# I2O device support +# +# CONFIG_I2O is not set + +# +# Networking support +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +# CONFIG_NETLINK_DEV is not set +CONFIG_UNIX=y +CONFIG_NET_KEY=m +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +CONFIG_INET_AH=m +CONFIG_INET_ESP=m +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_IP_TCPDIAG=m +# CONFIG_IP_TCPDIAG_IPV6 is not set + +# +# IP: Virtual Server Configuration +# +# CONFIG_IP_VS is not set +# CONFIG_IPV6 is not set +CONFIG_NETFILTER=y +# CONFIG_NETFILTER_DEBUG is not set + +# +# IP: Netfilter Configuration +# +CONFIG_IP_NF_CONNTRACK=m +# CONFIG_IP_NF_CT_ACCT is not set +CONFIG_IP_NF_CONNTRACK_MARK=y +# CONFIG_IP_NF_CT_PROTO_SCTP is not set +CONFIG_IP_NF_FTP=m +CONFIG_IP_NF_IRC=m +CONFIG_IP_NF_TFTP=m +CONFIG_IP_NF_AMANDA=m +CONFIG_IP_NF_QUEUE=m +CONFIG_IP_NF_IPTABLES=m +CONFIG_IP_NF_MATCH_LIMIT=m +CONFIG_IP_NF_MATCH_IPRANGE=m +CONFIG_IP_NF_MATCH_MAC=m +CONFIG_IP_NF_MATCH_PKTTYPE=m +CONFIG_IP_NF_MATCH_MARK=m +CONFIG_IP_NF_MATCH_MULTIPORT=m +CONFIG_IP_NF_MATCH_TOS=m +CONFIG_IP_NF_MATCH_RECENT=m +CONFIG_IP_NF_MATCH_ECN=m +CONFIG_IP_NF_MATCH_DSCP=m +CONFIG_IP_NF_MATCH_AH_ESP=m +CONFIG_IP_NF_MATCH_LENGTH=m +CONFIG_IP_NF_MATCH_TTL=m +CONFIG_IP_NF_MATCH_TCPMSS=m +CONFIG_IP_NF_MATCH_HELPER=m +CONFIG_IP_NF_MATCH_STATE=m +CONFIG_IP_NF_MATCH_CONNTRACK=m +CONFIG_IP_NF_MATCH_OWNER=m +CONFIG_IP_NF_MATCH_ADDRTYPE=m +CONFIG_IP_NF_MATCH_REALM=m +CONFIG_IP_NF_MATCH_SCTP=m +CONFIG_IP_NF_MATCH_COMMENT=m +CONFIG_IP_NF_MATCH_CONNMARK=m +CONFIG_IP_NF_MATCH_HASHLIMIT=m +CONFIG_IP_NF_FILTER=m +CONFIG_IP_NF_TARGET_REJECT=m +CONFIG_IP_NF_TARGET_LOG=m +CONFIG_IP_NF_TARGET_ULOG=m +CONFIG_IP_NF_TARGET_TCPMSS=m +CONFIG_IP_NF_NAT=m +CONFIG_IP_NF_NAT_NEEDED=y +CONFIG_IP_NF_TARGET_MASQUERADE=m +CONFIG_IP_NF_TARGET_REDIRECT=m +CONFIG_IP_NF_TARGET_NETMAP=m +CONFIG_IP_NF_TARGET_SAME=m +CONFIG_IP_NF_NAT_LOCAL=y +CONFIG_IP_NF_NAT_SNMP_BASIC=m +CONFIG_IP_NF_NAT_IRC=m +CONFIG_IP_NF_NAT_FTP=m +CONFIG_IP_NF_NAT_TFTP=m +CONFIG_IP_NF_NAT_AMANDA=m +CONFIG_IP_NF_MANGLE=m +CONFIG_IP_NF_TARGET_TOS=m +CONFIG_IP_NF_TARGET_ECN=m +CONFIG_IP_NF_TARGET_DSCP=m +CONFIG_IP_NF_TARGET_MARK=m +CONFIG_IP_NF_TARGET_CLASSIFY=m +CONFIG_IP_NF_TARGET_CONNMARK=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m +CONFIG_IP_NF_RAW=m +CONFIG_IP_NF_TARGET_NOTRACK=m +CONFIG_IP_NF_ARPTABLES=m +CONFIG_IP_NF_ARPFILTER=m +CONFIG_IP_NF_ARP_MANGLE=m +CONFIG_IP_NF_COMPAT_IPCHAINS=m +# CONFIG_IP_NF_COMPAT_IPFWADM is not set +CONFIG_XFRM=y +CONFIG_XFRM_USER=m + +# +# SCTP Configuration (EXPERIMENTAL) +# +# CONFIG_IP_SCTP is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_NET_DIVERT is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set +CONFIG_NET_CLS_ROUTE=y + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set + +# +# ARCnet devices +# +# CONFIG_ARCNET is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_HAPPYMEAL is not set +# CONFIG_SUNGEM is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_LANCE is not set +# CONFIG_NET_VENDOR_SMC is not set +# CONFIG_NET_VENDOR_RACAL is not set + +# +# Tulip family network device support +# +# CONFIG_NET_TULIP is not set +# CONFIG_AT1700 is not set +# CONFIG_DEPCA is not set +# CONFIG_HP100 is not set +# CONFIG_NET_ISA is not set +CONFIG_NET_PCI=y +# CONFIG_PCNET32 is not set +# CONFIG_AMD8111_ETH is not set +# CONFIG_ADAPTEC_STARFIRE is not set +# CONFIG_AC3200 is not set +# CONFIG_APRICOT is not set +# CONFIG_B44 is not set +# CONFIG_FORCEDETH is not set +# CONFIG_CS89x0 is not set +CONFIG_TC35815_1=y +# CONFIG_DGRS is not set +# CONFIG_EEPRO100 is not set +# CONFIG_E100 is not set +# CONFIG_FEALNX is not set +# CONFIG_NATSEMI is not set +# CONFIG_NE2K_PCI is not set +# CONFIG_8139CP is not set +CONFIG_8139TOO=y +# CONFIG_8139TOO_PIO is not set +# CONFIG_8139TOO_TUNE_TWISTER is not set +# CONFIG_8139TOO_8129 is not set +# CONFIG_8139_OLD_RX_RESET is not set +# CONFIG_SIS900 is not set +# CONFIG_EPIC100 is not set +# CONFIG_SUNDANCE is not set +# CONFIG_TLAN is not set +# CONFIG_VIA_RHINE is not set +# CONFIG_LAN_SAA9730 is not set +# CONFIG_NET_POCKET is not set +CONFIG_TXBOARD_OBNE_NET=y + +# +# Ethernet (1000 Mbit) +# +# CONFIG_ACENIC is not set +# CONFIG_DL2K is not set +# CONFIG_E1000 is not set +# CONFIG_NS83820 is not set +# CONFIG_HAMACHI is not set +# CONFIG_YELLOWFIN is not set +# CONFIG_R8169 is not set +# CONFIG_SK98LIN is not set +# CONFIG_VIA_VELOCITY is not set +# CONFIG_TIGON3 is not set + +# +# Ethernet (10000 Mbit) +# +# CONFIG_IXGB is not set +# CONFIG_S2IO is not set + +# +# Token Ring devices +# +# CONFIG_TR is not set + +# +# Wireless LAN (non-hamradio) +# +CONFIG_NET_RADIO=y + +# +# Obsolete Wireless cards support (pre-802.11) +# +# CONFIG_STRIP is not set +# CONFIG_ARLAN is not set +# CONFIG_WAVELAN is not set + +# +# Wireless 802.11b ISA/PCI cards support +# +# CONFIG_AIRO is not set +CONFIG_HERMES=m +# CONFIG_PLX_HERMES is not set +# CONFIG_TMD_HERMES is not set +CONFIG_PCI_HERMES=m +# CONFIG_ATMEL is not set + +# +# Prism GT/Duette 802.11(a/b/g) PCI/Cardbus support +# +# CONFIG_PRISM54 is not set +CONFIG_NET_WIRELESS=y + +# +# Wan interfaces +# +# CONFIG_WAN is not set +# CONFIG_FDDI is not set +# CONFIG_HIPPI is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NET_FC is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=m +CONFIG_INPUT_MOUSEDEV_PSAUX=y +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +CONFIG_INPUT_EVDEV=m +CONFIG_INPUT_EVBUG=m + +# +# Input I/O drivers +# +# CONFIG_GAMEPORT is not set +CONFIG_SOUND_GAMEPORT=y +CONFIG_SERIO=y +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_SERPORT is not set +# CONFIG_SERIO_CT82C710 is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_RAW is not set + +# +# Input Device Drivers +# +CONFIG_INPUT_KEYBOARD=y +CONFIG_KEYBOARD_ATKBD=y +# CONFIG_KEYBOARD_SUNKBD is not set +# CONFIG_KEYBOARD_LKKBD is not set +# CONFIG_KEYBOARD_XTKBD is not set +# CONFIG_KEYBOARD_NEWTON is not set +CONFIG_INPUT_MOUSE=y +CONFIG_MOUSE_PS2=y +# CONFIG_MOUSE_SERIAL is not set +# CONFIG_MOUSE_INPORT is not set +# CONFIG_MOUSE_LOGIBM is not set +# CONFIG_MOUSE_PC110PAD is not set +# CONFIG_MOUSE_VSXXXAA is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +# CONFIG_INPUT_MISC is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +CONFIG_SERIAL_NONSTANDARD=y +# CONFIG_COMPUTONE is not set +# CONFIG_ROCKETPORT is not set +# CONFIG_CYCLADES is not set +# CONFIG_DIGIEPCA is not set +# CONFIG_DIGI is not set +# CONFIG_ESPSERIAL is not set +# CONFIG_MOXA_INTELLIO is not set +# CONFIG_MOXA_SMARTIO is not set +# CONFIG_ISI is not set +# CONFIG_SYNCLINK is not set +# CONFIG_SYNCLINKMP is not set +# CONFIG_N_HDLC is not set +# CONFIG_RISCOM8 is not set +# CONFIG_SPECIALIX is not set +# CONFIG_SX is not set +# CONFIG_RIO is not set +# CONFIG_STALDRV is not set +# CONFIG_SERIAL_TX3912 is not set +# CONFIG_AU1000_UART is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_SERIAL_TXX9=y +CONFIG_SERIAL_TXX9_CONSOLE=y +CONFIG_SERIAL_TXX9_STDSERIAL=y +CONFIG_UNIX98_PTYS=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set + +# +# Watchdog Cards +# +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set + +# +# ISA-based Watchdog Cards +# +# CONFIG_PCWATCHDOG is not set +# CONFIG_MIXCOMWD is not set +# CONFIG_WDT is not set + +# +# PCI-based Watchdog Cards +# +# CONFIG_PCIPCWATCHDOG is not set +# CONFIG_WDTPCI is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_RTC is not set +CONFIG_GEN_RTC=y +CONFIG_GEN_RTC_X=y +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set +# CONFIG_APPLICOM is not set + +# +# Ftape, the floppy tape device driver +# +# CONFIG_AGP is not set +# CONFIG_DRM is not set +# CONFIG_RAW_DRIVER is not set + +# +# I2C support +# +CONFIG_I2C=y +CONFIG_I2C_CHARDEV=m + +# +# I2C Algorithms +# +CONFIG_I2C_ALGOBIT=y +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +# CONFIG_I2C_ALI1535 is not set +# CONFIG_I2C_ALI1563 is not set +# CONFIG_I2C_ALI15X3 is not set +# CONFIG_I2C_AMD756 is not set +# CONFIG_I2C_AMD8111 is not set +# CONFIG_I2C_ELEKTOR is not set +# CONFIG_I2C_I801 is not set +# CONFIG_I2C_I810 is not set +# CONFIG_I2C_ISA is not set +# CONFIG_I2C_NFORCE2 is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_PIIX4 is not set +# CONFIG_I2C_PROSAVAGE is not set +# CONFIG_I2C_SAVAGE4 is not set +# CONFIG_SCx200_ACB is not set +# CONFIG_I2C_SIS5595 is not set +# CONFIG_I2C_SIS630 is not set +# CONFIG_I2C_SIS96X is not set +# CONFIG_I2C_STUB is not set +# CONFIG_I2C_VIA is not set +# CONFIG_I2C_VIAPRO is not set +# CONFIG_I2C_VOODOO3 is not set +# CONFIG_I2C_PCA_ISA is not set + +# +# Hardware Sensors Chip support +# +# CONFIG_I2C_SENSOR is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_FSCHER is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_VIA686A is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83627HF is not set + +# +# Other I2C Chip support +# +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_RTC8564 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set + +# +# Misc devices +# + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set + +# +# Digital Video Broadcasting Devices +# +# CONFIG_DVB is not set + +# +# Graphics support +# +# CONFIG_FB is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +# CONFIG_MDA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y + +# +# Sound +# +CONFIG_SOUND=m + +# +# Advanced Linux Sound Architecture +# +CONFIG_SND=m +CONFIG_SND_TIMER=m +CONFIG_SND_PCM=m +CONFIG_SND_HWDEP=m +CONFIG_SND_RAWMIDI=m +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=m +CONFIG_SND_PCM_OSS=m +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set + +# +# Generic devices +# +CONFIG_SND_MPU401_UART=m +CONFIG_SND_OPL3_LIB=m +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set + +# +# ISA devices +# +# CONFIG_SND_AD1848 is not set +# CONFIG_SND_CS4231 is not set +# CONFIG_SND_CS4232 is not set +# CONFIG_SND_CS4236 is not set +# CONFIG_SND_ES1688 is not set +# CONFIG_SND_ES18XX is not set +# CONFIG_SND_GUSCLASSIC is not set +# CONFIG_SND_GUSEXTREME is not set +# CONFIG_SND_GUSMAX is not set +# CONFIG_SND_INTERWAVE is not set +# CONFIG_SND_INTERWAVE_STB is not set +# CONFIG_SND_OPTI92X_AD1848 is not set +# CONFIG_SND_OPTI92X_CS4231 is not set +# CONFIG_SND_OPTI93X is not set +# CONFIG_SND_SB8 is not set +# CONFIG_SND_SB16 is not set +# CONFIG_SND_SBAWE is not set +# CONFIG_SND_WAVEFRONT is not set +# CONFIG_SND_CMI8330 is not set +# CONFIG_SND_OPL3SA2 is not set +# CONFIG_SND_SGALAXY is not set +# CONFIG_SND_SSCAPE is not set + +# +# PCI devices +# +CONFIG_SND_AC97_CODEC=m +# CONFIG_SND_ALI5451 is not set +# CONFIG_SND_ATIIXP is not set +# CONFIG_SND_ATIIXP_MODEM is not set +# CONFIG_SND_AU8810 is not set +# CONFIG_SND_AU8820 is not set +# CONFIG_SND_AU8830 is not set +# CONFIG_SND_AZT3328 is not set +# CONFIG_SND_BT87X is not set +# CONFIG_SND_CS46XX is not set +# CONFIG_SND_CS4281 is not set +# CONFIG_SND_EMU10K1 is not set +# CONFIG_SND_KORG1212 is not set +# CONFIG_SND_MIXART is not set +# CONFIG_SND_NM256 is not set +# CONFIG_SND_RME32 is not set +# CONFIG_SND_RME96 is not set +# CONFIG_SND_RME9652 is not set +# CONFIG_SND_HDSP is not set +# CONFIG_SND_TRIDENT is not set +CONFIG_SND_YMFPCI=m +# CONFIG_SND_ALS4000 is not set +CONFIG_SND_CMIPCI=m +# CONFIG_SND_ENS1370 is not set +# CONFIG_SND_ENS1371 is not set +# CONFIG_SND_ES1938 is not set +# CONFIG_SND_ES1968 is not set +# CONFIG_SND_MAESTRO3 is not set +# CONFIG_SND_FM801 is not set +# CONFIG_SND_ICE1712 is not set +# CONFIG_SND_ICE1724 is not set +# CONFIG_SND_INTEL8X0 is not set +# CONFIG_SND_INTEL8X0M is not set +# CONFIG_SND_SONICVIBES is not set +# CONFIG_SND_VIA82XX is not set +# CONFIG_SND_VX222 is not set + +# +# USB devices +# +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_USX2Y is not set + +# +# ALSA MIPS devices +# +# CONFIG_SND_TX49XX is not set + +# +# Open Sound System +# +# CONFIG_SOUND_PRIME is not set + +# +# USB support +# +CONFIG_USB=m +# CONFIG_USB_DEBUG is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +# CONFIG_USB_BANDWIDTH is not set +# CONFIG_USB_DYNAMIC_MINORS is not set +# CONFIG_USB_OTG is not set +CONFIG_USB_ARCH_HAS_HCD=y +CONFIG_USB_ARCH_HAS_OHCI=y + +# +# USB Host Controller Drivers +# +CONFIG_USB_EHCI_HCD=m +# CONFIG_USB_EHCI_SPLIT_ISO is not set +# CONFIG_USB_EHCI_ROOT_HUB_TT is not set +CONFIG_USB_OHCI_HCD=m +CONFIG_USB_UHCI_HCD=m +# CONFIG_USB_SL811_HCD is not set + +# +# USB Device Class drivers +# +# CONFIG_USB_AUDIO is not set +# CONFIG_USB_BLUETOOTH_TTY is not set +# CONFIG_USB_MIDI is not set +# CONFIG_USB_ACM is not set +# CONFIG_USB_PRINTER is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=m +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_RW_DETECT is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_HP8200e is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=m +CONFIG_USB_HIDINPUT=y +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +# CONFIG_USB_AIPTEK is not set +# CONFIG_USB_WACOM is not set +# CONFIG_USB_KBTAB is not set +# CONFIG_USB_POWERMATE is not set +# CONFIG_USB_MTOUCH is not set +# CONFIG_USB_EGALAX is not set +# CONFIG_USB_XPAD is not set +# CONFIG_USB_ATI_REMOTE is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set +# CONFIG_USB_HPUSBSCSI is not set + +# +# USB Multimedia devices +# +# CONFIG_USB_DABUSB is not set + +# +# Video4Linux support is needed for USB Multimedia device support +# + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +CONFIG_USB_USBNET=m + +# +# USB Host-to-Host Cables +# +# CONFIG_USB_ALI_M5632 is not set +# CONFIG_USB_AN2720 is not set +# CONFIG_USB_BELKIN is not set +# CONFIG_USB_GENESYS is not set +# CONFIG_USB_NET1080 is not set +# CONFIG_USB_PL2301 is not set +# CONFIG_USB_KC2190 is not set + +# +# Intelligent USB Devices/Gadgets +# +# CONFIG_USB_ARMLINUX is not set +# CONFIG_USB_EPSON2888 is not set +# CONFIG_USB_ZAURUS is not set +CONFIG_USB_CDCETHER=y + +# +# USB Network Adapters +# +# CONFIG_USB_AX8817X is not set + +# +# USB port drivers +# + +# +# USB Serial Converter support +# +CONFIG_USB_SERIAL=m +CONFIG_USB_SERIAL_GENERIC=y +# CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_WHITEHEAT is not set +# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set +# CONFIG_USB_SERIAL_CYPRESS_M8 is not set +# CONFIG_USB_SERIAL_EMPEG is not set +# CONFIG_USB_SERIAL_FTDI_SIO is not set +# CONFIG_USB_SERIAL_VISOR is not set +# CONFIG_USB_SERIAL_IPAQ is not set +# CONFIG_USB_SERIAL_IR is not set +# CONFIG_USB_SERIAL_EDGEPORT is not set +# CONFIG_USB_SERIAL_EDGEPORT_TI is not set +# CONFIG_USB_SERIAL_IPW is not set +# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set +# CONFIG_USB_SERIAL_KEYSPAN is not set +# CONFIG_USB_SERIAL_KLSI is not set +# CONFIG_USB_SERIAL_KOBIL_SCT is not set +# CONFIG_USB_SERIAL_MCT_U232 is not set +CONFIG_USB_SERIAL_PL2303=m +# CONFIG_USB_SERIAL_SAFE is not set +# CONFIG_USB_SERIAL_CYBERJACK is not set +# CONFIG_USB_SERIAL_XIRCOM is not set +# CONFIG_USB_SERIAL_OMNINET is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_TIGL is not set +# CONFIG_USB_AUERSWALD is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGETKIT is not set +# CONFIG_USB_PHIDGETSERVO is not set +# CONFIG_USB_TEST is not set + +# +# USB ATM/DSL drivers +# + +# +# USB Gadget Support +# +CONFIG_USB_GADGET=m +# CONFIG_USB_GADGET_DEBUG_FILES is not set +# CONFIG_USB_GADGET_NET2280 is not set +# CONFIG_USB_GADGET_PXA2XX is not set +CONFIG_USB_GADGET_GOKU=y +CONFIG_USB_GOKU=m +# CONFIG_USB_GADGET_SA1100 is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +CONFIG_USB_ZERO=m +CONFIG_USB_ETH=m +CONFIG_USB_ETH_RNDIS=y +# CONFIG_USB_GADGETFS is not set +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m + +# +# MMC/SD Card support +# +# CONFIG_MMC is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_FS_XATTR is not set +CONFIG_JBD=y +# CONFIG_JBD_DEBUG is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_XFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_QUOTA is not set +CONFIG_DNOTIFY=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set + +# +# CD-ROM/DVD Filesystems +# +CONFIG_ISO9660_FS=y +CONFIG_JOLIET=y +# CONFIG_ZISOFS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=m +# CONFIG_MSDOS_FS is not set +CONFIG_VFAT_FS=m +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_KCORE=y +CONFIG_SYSFS=y +# CONFIG_DEVFS_FS is not set +# CONFIG_DEVPTS_FS_XATTR is not set +CONFIG_TMPFS=y +# CONFIG_TMPFS_XATTR is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_PRAMFS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_JFFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_NAND=y +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +CONFIG_CRAMFS=y +# CONFIG_CRAMFS_EXPAND_SIZE is not set +# CONFIG_CRAMFS_LINEAR is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_ROOT_NFS=y +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +# CONFIG_EXPORTFS is not set +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=m +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +CONFIG_NLS_CODEPAGE_932=m +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=m +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set + +# +# Kernel hacking +# +CONFIG_DEBUG_KERNEL=y +CONFIG_MAGIC_SYSRQ=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_SPINLOCK is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_INFO is not set +CONFIG_CROSSCOMPILE=y +CONFIG_CMDLINE="" +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_KGDB is not set +# CONFIG_RUNTIME_DEBUG is not set +# CONFIG_MIPS_UNCACHED is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set + +# +# Cryptographic options +# +CONFIG_CRYPTO=y +CONFIG_CRYPTO_HMAC=y +CONFIG_CRYPTO_NULL=m +CONFIG_CRYPTO_MD4=m +CONFIG_CRYPTO_MD5=m +CONFIG_CRYPTO_SHA1=m +CONFIG_CRYPTO_SHA256=m +CONFIG_CRYPTO_SHA512=m +CONFIG_CRYPTO_WP512=m +CONFIG_CRYPTO_DES=m +CONFIG_CRYPTO_BLOWFISH=m +CONFIG_CRYPTO_TWOFISH=m +CONFIG_CRYPTO_SERPENT=m +CONFIG_CRYPTO_AES=m +CONFIG_CRYPTO_CAST5=m +CONFIG_CRYPTO_CAST6=m +CONFIG_CRYPTO_TEA=m +CONFIG_CRYPTO_ARC4=m +CONFIG_CRYPTO_KHAZAD=m +CONFIG_CRYPTO_ANUBIS=m +CONFIG_CRYPTO_DEFLATE=m +CONFIG_CRYPTO_MICHAEL_MIC=m +CONFIG_CRYPTO_CRC32C=m +CONFIG_CRYPTO_TEST=m + +# +# Library routines +# +# CONFIG_CRC_CCITT is not set +CONFIG_CRC32=y +CONFIG_LIBCRC32C=m +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_IRQ_PROBE=y diff -u -rN -p linux-2.6.10/arch/mips/kernel/Makefile linux-2.6.10-rbtx49/arch/mips/kernel/Makefile --- linux-2.6.10/arch/mips/kernel/Makefile 2004-12-25 06:34:32.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/Makefile 2005-04-22 14:46:18.000000000 +0900 @@ -53,7 +53,10 @@ obj-$(CONFIG_PROC_FS) += proc.o obj-$(CONFIG_MIPS64) += cpu-bugs64.o +ifndef CONFIG_TX_BOARDS +# use native get_rtc_time,set_rtc_time,etc. obj-$(CONFIG_GEN_RTC) += genrtc.o +endif CFLAGS_cpu-bugs64.o = $(shell if $(CC) $(CFLAGS) -Wa,-mdaddi -c -o /dev/null -xc /dev/null >/dev/null 2>&1; then echo "-DHAVE_AS_SET_DADDI"; fi) CFLAGS_ioctl32.o += -Ifs/ diff -u -rN -p linux-2.6.10/arch/mips/kernel/binfmt_elfo32.c linux-2.6.10-rbtx49/arch/mips/kernel/binfmt_elfo32.c --- linux-2.6.10/arch/mips/kernel/binfmt_elfo32.c 2004-12-25 06:34:30.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/binfmt_elfo32.c 2005-04-22 14:46:18.000000000 +0900 @@ -54,7 +54,6 @@ typedef elf_fpreg_t elf_fpregset_t[ELF_N #include #include -#include #include #include @@ -98,7 +97,7 @@ struct elf_prpsinfo32 #define init_elf_binfmt init_elf32_binfmt #define jiffies_to_timeval jiffies_to_compat_timeval -static __inline__ void +static inline void jiffies_to_compat_timeval(unsigned long jiffies, struct compat_timeval *value) { /* @@ -113,21 +112,26 @@ jiffies_to_compat_timeval(unsigned long #undef ELF_CORE_COPY_REGS #define ELF_CORE_COPY_REGS(_dest,_regs) elf32_core_copy_regs(_dest,_regs); -void elf32_core_copy_regs(elf_gregset_t _dest, struct pt_regs *_regs) +void elf32_core_copy_regs(elf_gregset_t grp, struct pt_regs *regs) { int i; - memset(_dest, 0, sizeof(elf_gregset_t)); - - /* XXXKW the 6 is from EF_REG0 in gdb/gdb/mips-linux-tdep.c, include/asm-mips/reg.h */ - for (i=6; i<38; i++) - _dest[i] = (elf_greg_t) _regs->regs[i-6]; - _dest[i++] = (elf_greg_t) _regs->lo; - _dest[i++] = (elf_greg_t) _regs->hi; - _dest[i++] = (elf_greg_t) _regs->cp0_epc; - _dest[i++] = (elf_greg_t) _regs->cp0_badvaddr; - _dest[i++] = (elf_greg_t) _regs->cp0_status; - _dest[i++] = (elf_greg_t) _regs->cp0_cause; + for (i = 0; i < EF_R0; i++) + grp[i] = 0; + grp[EF_R0] = 0; + for (i = 1; i <= 31; i++) + grp[EF_R0 + i] = (elf_greg_t) regs->regs[i]; + grp[EF_R26] = 0; + grp[EF_R27] = 0; + grp[EF_LO] = (elf_greg_t) regs->lo; + grp[EF_HI] = (elf_greg_t) regs->hi; + grp[EF_CP0_EPC] = (elf_greg_t) regs->cp0_epc; + grp[EF_CP0_BADVADDR] = (elf_greg_t) regs->cp0_badvaddr; + grp[EF_CP0_STATUS] = (elf_greg_t) regs->cp0_status; + grp[EF_CP0_CAUSE] = (elf_greg_t) regs->cp0_cause; +#ifdef EF_UNUSED0 + grp[EF_UNUSED0] = 0; +#endif } MODULE_DESCRIPTION("Binary format loader for compatibility with o32 Linux/MIPS binaries"); @@ -136,4 +140,7 @@ MODULE_AUTHOR("Ralf Baechle (ralf@linux- #undef MODULE_DESCRIPTION #undef MODULE_AUTHOR +#undef TASK_SIZE +#define TASK_SIZE TASK_SIZE32 + #include "../../../fs/binfmt_elf.c" diff -u -rN -p linux-2.6.10/arch/mips/kernel/entry.S linux-2.6.10-rbtx49/arch/mips/kernel/entry.S --- linux-2.6.10/arch/mips/kernel/entry.S 2004-12-25 06:34:02.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/entry.S 2005-04-22 14:46:18.000000000 +0900 @@ -19,11 +19,11 @@ #include #ifdef CONFIG_PREEMPT - .macro preempt_stop reg=t0 + .macro preempt_stop .endm #else - .macro preempt_stop reg=t0 - local_irq_disable \reg + .macro preempt_stop + local_irq_disable .endm #define resume_kernel restore_all #endif @@ -37,17 +37,17 @@ FEXPORT(ret_from_irq) andi t0, t0, KU_USER beqz t0, resume_kernel -FEXPORT(resume_userspace) - local_irq_disable t0 # make sure we dont miss an +resume_userspace: + local_irq_disable # make sure we dont miss an # interrupt setting need_resched # between sampling and return LONG_L a2, TI_FLAGS($28) # current->work - andi a2, _TIF_WORK_MASK # (ignoring syscall_trace) - bnez a2, work_pending + andi t0, a2, _TIF_WORK_MASK # (ignoring syscall_trace) + bnez t0, work_pending j restore_all #ifdef CONFIG_PREEMPT -ENTRY(resume_kernel) +resume_kernel: lw t0, TI_PRE_COUNT($28) bnez t0, restore_all need_resched: @@ -59,10 +59,10 @@ need_resched: beqz t0, restore_all li t0, PREEMPT_ACTIVE sw t0, TI_PRE_COUNT($28) - local_irq_enable t0 + local_irq_enable jal schedule sw zero, TI_PRE_COUNT($28) - local_irq_disable t0 + local_irq_disable b need_resched #endif @@ -88,13 +88,13 @@ FEXPORT(restore_partial) # restore part RESTORE_SP_AND_RET .set at -FEXPORT(work_pending) - andi t0, a2, _TIF_NEED_RESCHED +work_pending: + andi t0, a2, _TIF_NEED_RESCHED # a2 is preloaded with TI_FLAGS beqz t0, work_notifysig work_resched: jal schedule - local_irq_disable t0 # make sure need_resched and + local_irq_disable # make sure need_resched and # signals dont change between # sampling and return LONG_L a2, TI_FLAGS($28) @@ -113,11 +113,10 @@ work_notifysig: # deal with pending s FEXPORT(syscall_exit_work_partial) SAVE_STATIC -FEXPORT(syscall_exit_work) - LONG_L t0, TI_FLAGS($28) - li t1, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT - and t0, t1 - beqz t0, work_pending # trace bit is set +syscall_exit_work: + li t0, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT + and t0, a2 # a2 is preloaded with TI_FLAGS + beqz t0, work_pending # trace bit set? local_irq_enable # could let do_syscall_trace() # call schedule() instead move a0, sp @@ -128,28 +127,25 @@ FEXPORT(syscall_exit_work) /* * Common spurious interrupt handler. */ - .text - .align 5 LEAF(spurious_interrupt) /* * Someone tried to fool us by sending an interrupt but we * couldn't find a cause for it. */ + PTR_LA t1, irq_err_count #ifdef CONFIG_SMP - lui t1, %hi(irq_err_count) -1: ll t0, %lo(irq_err_count)(t1) +1: ll t0, (t1) addiu t0, 1 - sc t0, %lo(irq_err_count)(t1) + sc t0, (t1) #if R10000_LLSC_WAR beqzl t0, 1b #else beqz t0, 1b #endif #else - lui t1, %hi(irq_err_count) - lw t0, %lo(irq_err_count)(t1) + lw t0, (t1) addiu t0, 1 - sw t0, %lo(irq_err_count)(t1) + sw t0, (t1) #endif j ret_from_irq END(spurious_interrupt) diff -u -rN -p linux-2.6.10/arch/mips/kernel/head.S linux-2.6.10-rbtx49/arch/mips/kernel/head.S --- linux-2.6.10/arch/mips/kernel/head.S 2004-12-25 06:35:01.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/head.S 2005-04-22 14:46:18.000000000 +0900 @@ -136,6 +136,23 @@ EXPORT(_stext) NESTED(kernel_entry, 16, sp) # kernel entry point setup_c0_status_pri +#ifdef CONFIG_XIP_KERNEL + /* + * For xip from rom, copy initialized data from end of text + * in rom to _fdata though _edata in ram. + */ + la s0, _etext + la s1, _fdata + la s2, _edata +1: + lw t0, (s0) + sw t0, (s1) + addi s1, 4 + addi s0, 4 + bne s1, s2, 1b + +#endif + #ifdef CONFIG_SGI_IP27 GET_NASID_ASM t1 move t2, t1 # text and data are here @@ -200,19 +217,13 @@ NESTED(smp_bootstrap, 16, sp) .comm fw_arg2, SZREG, SZREG .comm fw_arg3, SZREG, SZREG - .macro page name, order=0 - .globl \name -\name: .size \name, (_PAGE_SIZE << \order) - .org . + (_PAGE_SIZE << \order) - .type \name, @object + .macro page name, order + .comm \name, (_PAGE_SIZE << \order), (_PAGE_SIZE << \order) .endm - .data - .align PAGE_SHIFT - /* - * ... but on 64-bit we've got three-level pagetables with a - * slightly different layout ... + * On 64-bit we've got three-level pagetables with a slightly + * different layout ... */ page swapper_pg_dir, _PGD_ORDER #ifdef CONFIG_MIPS64 diff -u -rN -p linux-2.6.10/arch/mips/kernel/process.c linux-2.6.10-rbtx49/arch/mips/kernel/process.c --- linux-2.6.10/arch/mips/kernel/process.c 2004-12-25 06:34:32.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/process.c 2005-04-22 14:46:18.000000000 +0900 @@ -153,6 +153,44 @@ int copy_thread(int nr, unsigned long cl int dump_fpu(struct pt_regs *regs, elf_fpregset_t *r) { memcpy(r, ¤t->thread.fpu, sizeof(current->thread.fpu)); + + return 1; +} + +void dump_regs(elf_greg_t *gp, struct pt_regs *regs) +{ + int i; + + for (i = 0; i < EF_R0; i++) + gp[i] = 0; + gp[EF_R0] = 0; + for (i = 1; i <= 31; i++) + gp[EF_R0 + i] = regs->regs[i]; + gp[EF_R26] = 0; + gp[EF_R27] = 0; + gp[EF_LO] = regs->lo; + gp[EF_HI] = regs->hi; + gp[EF_CP0_EPC] = regs->cp0_epc; + gp[EF_CP0_BADVADDR] = regs->cp0_badvaddr; + gp[EF_CP0_STATUS] = regs->cp0_status; + gp[EF_CP0_CAUSE] = regs->cp0_cause; +#ifdef EF_UNUSED0 + gp[EF_UNUSED0] = 0; +#endif +} + +int dump_task_regs (struct task_struct *tsk, elf_gregset_t *regs) +{ + struct thread_info *ti = tsk->thread_info; + long ksp = (unsigned long)ti + THREAD_SIZE - 32; + dump_regs(&(*regs)[0], (struct pt_regs *) ksp - 1); + return 1; +} + +int dump_task_fpu (struct task_struct *t, elf_fpregset_t *fpr) +{ + memcpy(fpr, &t->thread.fpu, sizeof(current->thread.fpu)); + return 1; } @@ -190,11 +228,6 @@ struct mips_frame_info { int pc_offset; }; static struct mips_frame_info schedule_frame; -static struct mips_frame_info schedule_timeout_frame; -static struct mips_frame_info sleep_on_frame; -static struct mips_frame_info sleep_on_timeout_frame; -static struct mips_frame_info wait_for_completion_frame; -static int mips_frame_info_initialized; static int __init get_frame_info(struct mips_frame_info *info, void *func) { int i; @@ -246,14 +279,7 @@ static int __init get_frame_info(struct static int __init frame_info_init(void) { - mips_frame_info_initialized = - !get_frame_info(&schedule_frame, schedule) && - !get_frame_info(&schedule_timeout_frame, schedule_timeout) && - !get_frame_info(&sleep_on_frame, sleep_on) && - !get_frame_info(&sleep_on_timeout_frame, sleep_on_timeout) && - !get_frame_info(&wait_for_completion_frame, wait_for_completion); - - return 0; + return get_frame_info(&schedule_frame, schedule); } arch_initcall(frame_info_init); @@ -263,7 +289,6 @@ arch_initcall(frame_info_init); */ unsigned long thread_saved_pc(struct task_struct *tsk) { - extern void ret_from_fork(void); struct thread_struct *t = &tsk->thread; /* New born processes are a special case */ @@ -275,59 +300,14 @@ unsigned long thread_saved_pc(struct tas return ((unsigned long *)t->reg29)[schedule_frame.pc_offset]; } -/* get_wchan - a maintenance nightmare^W^Wpain in the ass ... */ unsigned long get_wchan(struct task_struct *p) { - unsigned long frame, pc; + unsigned long pc; if (!p || p == current || p->state == TASK_RUNNING) return 0; - if (!mips_frame_info_initialized) - return 0; pc = thread_saved_pc(p); - if (!in_sched_functions(pc)) - goto out; - - if (pc >= (unsigned long) sleep_on_timeout) - goto schedule_timeout_caller; - if (pc >= (unsigned long) sleep_on) - goto schedule_caller; - if (pc >= (unsigned long) interruptible_sleep_on_timeout) - goto schedule_timeout_caller; - if (pc >= (unsigned long)interruptible_sleep_on) - goto schedule_caller; - if (pc >= (unsigned long)wait_for_completion) - goto schedule_caller; - goto schedule_timeout_caller; - -schedule_caller: - frame = ((unsigned long *)p->thread.reg30)[schedule_frame.frame_offset]; - if (pc >= (unsigned long) sleep_on) - pc = ((unsigned long *)frame)[sleep_on_frame.pc_offset]; - else - pc = ((unsigned long *)frame)[wait_for_completion_frame.pc_offset]; - goto out; - -schedule_timeout_caller: - /* - * The schedule_timeout frame - */ - frame = ((unsigned long *)p->thread.reg30)[schedule_frame.frame_offset]; - - /* - * frame now points to sleep_on_timeout's frame - */ - pc = ((unsigned long *)frame)[schedule_timeout_frame.pc_offset]; - - if (in_sched_functions(pc)) { - /* schedule_timeout called by [interruptible_]sleep_on_timeout */ - frame = ((unsigned long *)frame)[schedule_timeout_frame.frame_offset]; - pc = ((unsigned long *)frame)[sleep_on_timeout_frame.pc_offset]; - } - -out: - #ifdef CONFIG_MIPS64 if (current->thread.mflags & MF_32BIT_REGS) /* Kludge for 32-bit ps */ pc &= 0xffffffffUL; diff -u -rN -p linux-2.6.10/arch/mips/kernel/ptrace.c linux-2.6.10-rbtx49/arch/mips/kernel/ptrace.c --- linux-2.6.10/arch/mips/kernel/ptrace.c 2004-12-25 06:35:49.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/ptrace.c 2005-04-22 14:46:18.000000000 +0900 @@ -167,10 +167,12 @@ asmlinkage int sys_ptrace(long request, if (!cpu_has_fpu) break; + preempt_disable(); flags = read_c0_status(); __enable_fpu(); __asm__ __volatile__("cfc1\t%0,$0": "=r" (tmp)); write_c0_status(flags); + preempt_enable(); break; } default: diff -u -rN -p linux-2.6.10/arch/mips/kernel/scall32-o32.S linux-2.6.10-rbtx49/arch/mips/kernel/scall32-o32.S --- linux-2.6.10/arch/mips/kernel/scall32-o32.S 2004-12-25 06:33:59.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/scall32-o32.S 2005-04-22 14:46:18.000000000 +0900 @@ -5,6 +5,7 @@ * * Copyright (C) 1995, 96, 97, 98, 99, 2000, 01, 02 by Ralf Baechle * Copyright (C) 2001 MIPS Technologies, Inc. + * Copyright (C) 2004 Thiemo Seufer */ #include #include @@ -32,26 +33,30 @@ NESTED(handle_sys, PT_SIZE, sp) lw t1, PT_EPC(sp) # skip syscall on return +#if defined(CONFIG_BINFMT_IRIX) sltiu t0, v0, MAX_SYSCALL_NO + 1 # check syscall number +#else + subu v0, v0, __NR_O32_Linux # check syscall number + sltiu t0, v0, __NR_O32_Linux_syscalls + 1 +#endif addiu t1, 4 # skip to next instruction sw t1, PT_EPC(sp) beqz t0, illegal_syscall - /* XXX Put both in one cacheline, should save a bit. */ - sll t0, v0, 2 - lw t2, sys_call_table(t0) # syscall routine - lbu t3, sys_narg_table(v0) # number of arguments - beqz t2, illegal_syscall; + sll t0, v0, 3 + la t1, sys_call_table + addu t1, t0 + lw t2, (t1) # syscall routine + lw t3, 4(t1) # >= 0 if we need stack arguments + beqz t2, illegal_syscall - subu t0, t3, 5 # 5 or more arguments? sw a3, PT_R26(sp) # save a3 for syscall restarting - bgez t0, stackargs + bgez t3, stackargs stack_done: - sw a3, PT_R26(sp) # save for syscall restart - LONG_L t0, TI_FLAGS($28) # syscall tracing enabled? + lw t0, TI_FLAGS($28) # syscall tracing enabled? li t1, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT - and t0, t1, t0 + and t0, t1 bnez t0, syscall_trace_entry # -> yes jalr t2 # Do The Real Thing (TM) @@ -70,9 +75,9 @@ o32_syscall_exit: local_irq_disable # make sure need_resched and # signals dont change between # sampling and return - LONG_L a2, TI_FLAGS($28) # current->work + lw a2, TI_FLAGS($28) # current->work li t0, _TIF_ALLWORK_MASK - and t0, a2, t0 + and t0, a2 bnez t0, o32_syscall_exit_work j restore_partial @@ -116,49 +121,48 @@ syscall_trace_entry: */ stackargs: lw t0, PT_R29(sp) # get old user stack pointer - subu t3, 4 - sll t1, t3, 2 # stack valid? - addu t1, t0 # end address - or t0, t1 - bltz t0, bad_stack # -> sp is bad - - lw t0, PT_R29(sp) # get old user stack pointer - PTR_LA t1, 4f # copy 1 to 3 arguments - sll t3, t3, 4 - subu t1, t3 - jr t1 - - /* Ok, copy the args from the luser stack to the kernel stack */ /* - * I know Ralf doesn't like nops but this avoids code - * duplication for R3000 targets (and this is the - * only place where ".set reorder" doesn't help). - * Harald. + * We intentionally keep the kernel stack a little below the top of + * userspace so we don't have to do a slower byte accurate check here. + */ + lw t5, TI_ADDR_LIMIT($28) + addu t4, t0, 32 + and t5, t4 + bltz t5, bad_stack # -> sp is bad + + /* Ok, copy the args from the luser stack to the kernel stack. + * t3 is the precomputed number of instruction bytes needed to + * load or store arguments 6-8. */ + + la t1, 5f # load up to 3 arguments + subu t1, t3 +1: lw t5, 16(t0) # argument #5 from usp .set push .set noreorder .set nomacro -1: lw t1, 24(t0) # argument #7 from usp - nop - sw t1, 24(sp) - nop -2: lw t1, 20(t0) # argument #5 from usp - nop - sw t1, 20(sp) - nop -3: lw t1, 16(t0) # argument #5 from usp - nop - sw t1, 16(sp) - nop -4: .set pop + jr t1 + addiu t1, 6f - 5f - j stack_done # go back +2: lw t8, 28(t0) # argument #8 from usp +3: lw t7, 24(t0) # argument #7 from usp +4: lw t6, 20(t0) # argument #6 from usp +5: jr t1 + sw t5, 16(sp) # argument #5 to ksp + + sw t8, 28(sp) # argument #8 to ksp + sw t7, 24(sp) # argument #7 to ksp + sw t6, 20(sp) # argument #6 to ksp +6: j stack_done # go back + nop + .set pop .section __ex_table,"a" PTR 1b,bad_stack PTR 2b,bad_stack PTR 3b,bad_stack + PTR 4b,bad_stack .previous /* @@ -177,7 +181,7 @@ bad_stack: * The system call does not exist in this kernel */ illegal_syscall: - li v0, ENOSYS # error + li v0, -ENOSYS # error sw v0, PT_R2(sp) li t0, 1 # set error flag sw t0, PT_R7(sp) @@ -238,12 +242,12 @@ illegal_syscall: sw v0, PT_R2(sp) # result /* Success, so skip usual error handling garbage. */ - LONG_L a2, TI_FLAGS($28) # syscall tracing enabled? + lw a2, TI_FLAGS($28) # syscall tracing enabled? li t0, _TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT and t0, a2, t0 bnez t0, 1f - b o32_syscall_exit + j o32_syscall_exit 1: SAVE_STATIC move a0, sp @@ -269,69 +273,49 @@ bad_alignment: END(sys_sysmips) LEAF(sys_syscall) - lw t0, PT_R29(sp) # user sp - - sltu v0, a0, __NR_O32_Linux + __NR_O32_Linux_syscalls + 1 - beqz v0, enosys - - sll v0, a0, 2 - la v1, sys_syscall - lw t2, sys_call_table(v0) # function pointer - lbu t4, sys_narg_table(a0) # number of arguments - - li v0, -EINVAL - beq t2, v1, out # do not recurse +#if defined(CONFIG_BINFMT_IRIX) + sltiu v0, a0, MAX_SYSCALL_NO + 1 # check syscall number +#else + subu t0, a0, __NR_O32_Linux # check syscall number + sltiu v0, t0, __NR_O32_Linux_syscalls + 1 +#endif + sll t1, t0, 3 + beqz v0, einval - beqz t2, enosys # null function pointer? + lw t2, sys_call_table(t1) # syscall routine - andi v0, t0, 0x3 # unaligned stack pointer? - bnez v0, sigsegv +#if defined(CONFIG_BINFMT_IRIX) + li v1, 4000 # nr of sys_syscall +#else + li v1, 4000 - __NR_O32_Linux # index of sys_syscall +#endif + beq t0, v1, einval # do not recurse - addu v0, t0, 16 # v0 = usp + 16 - addu t1, v0, 12 # 3 32-bit arguments - lw v1, TI_ADDR_LIMIT($28) - or v0, v0, t1 - and v1, v1, v0 - bltz v1, efault + /* Some syscalls like execve get their arguments from struct pt_regs + and claim zero arguments in the syscall table. Thus we have to + assume the worst case and shuffle around all potential arguments. + If you want performance, don't use indirect syscalls. */ move a0, a1 # shift argument registers move a1, a2 move a2, a3 - -1: lw a3, 16(t0) -2: lw t3, 20(t0) -3: lw t4, 24(t0) - - .section __ex_table, "a" - .word 1b, efault - .word 2b, efault - .word 3b, efault - .previous - - sw t3, 16(sp) # put into new stackframe - sw t4, 20(sp) - - bnez t4, 1f # zero arguments? - addu a0, sp, 32 # then pass sp in a0 -1: - - sw t3, 16(sp) - sw v1, 20(sp) + lw a3, 16(sp) + lw t4, 20(sp) + lw t5, 24(sp) + lw t6, 28(sp) + sw t4, 16(sp) + sw t5, 20(sp) + sw t6, 24(sp) + sw a0, PT_R4(sp) # .. and push back a0 - a3, some + sw a1, PT_R5(sp) # syscalls expect them there + sw a2, PT_R6(sp) + sw a3, PT_R7(sp) + sw a3, PT_R26(sp) # update a3 for syscall restarting jr t2 /* Unreached */ -enosys: li v0, -ENOSYS - b out - -sigsegv: - li a0, _SIGSEGV - move a1, $28 - jal force_sig - /* Fall through */ - -efault: li v0, -EFAULT - -out: jr ra +einval: li v0, -EINVAL + jr ra END(sys_syscall) .macro fifty ptr, nargs, from=1, to=50 @@ -349,12 +333,14 @@ out: jr ra .endm .macro syscalltable +#if defined(CONFIG_BINFMT_IRIX) mille sys_ni_syscall 0 /* 0 - 999 SVR4 flavour */ - #include "irix5sys.h" /* 1000 - 1999 32-bit IRIX */ + mille sys_ni_syscall 0 /* 1000 - 1999 32-bit IRIX */ mille sys_ni_syscall 0 /* 2000 - 2999 BSD43 flavour */ mille sys_ni_syscall 0 /* 3000 - 3999 POSIX flavour */ +#endif - sys sys_syscall 0 /* 4000 */ + sys sys_syscall 8 /* 4000 */ sys sys_exit 1 sys sys_fork 0 sys sys_read 3 @@ -405,7 +391,7 @@ out: jr ra sys sys_ni_syscall 0 /* was signal(2) */ sys sys_geteuid 0 sys sys_getegid 0 /* 4050 */ - sys sys_acct 0 + sys sys_acct 1 sys sys_umount 2 sys sys_ni_syscall 0 sys sys_ioctl 3 @@ -485,7 +471,7 @@ out: jr ra sys sys_init_module 5 sys sys_delete_module 1 sys sys_ni_syscall 0 /* 4130 was get_kernel_syms */ - sys sys_quotactl 0 + sys sys_quotactl 4 sys sys_getpgid 1 sys sys_fchdir 1 sys sys_bdflush 2 @@ -506,7 +492,7 @@ out: jr ra sys sys_sysmips 4 sys sys_ni_syscall 0 /* 4150 */ sys sys_getsid 1 - sys sys_fdatasync 0 + sys sys_fdatasync 1 sys sys_sysctl 1 sys sys_mlock 2 sys sys_munlock 2 /* 4155 */ @@ -640,19 +626,16 @@ out: jr ra .endm + /* We pre-compute the number of _instruction_ bytes needed to + load or store the arguments 6-8. Negative values are ignored. */ + .macro sys function, nargs PTR \function + LONG (\nargs << 2) - (5 << 2) .endm .align 3 -sys_call_table: + .type sys_call_table,@object +EXPORT(sys_call_table) syscalltable .size sys_call_table, . - sys_call_table - - .macro sys function, nargs - .byte \nargs - .endm - -sys_narg_table: - syscalltable - .size sys_narg_table, . - sys_narg_table diff -u -rN -p linux-2.6.10/arch/mips/kernel/setup.c linux-2.6.10-rbtx49/arch/mips/kernel/setup.c --- linux-2.6.10/arch/mips/kernel/setup.c 2004-12-25 06:34:02.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/setup.c 2005-04-22 14:46:18.000000000 +0900 @@ -76,7 +76,11 @@ static char command_line[CL_SIZE]; * mips_io_port_base is the begin of the address space to which x86 style * I/O ports are mapped. */ +#ifdef CONFIG_XIP_KERNEL +unsigned long mips_io_port_base = -1; +#else const unsigned long mips_io_port_base = -1; +#endif EXPORT_SYMBOL(mips_io_port_base); /* @@ -443,7 +447,11 @@ static inline void resource_init(void) code_resource.start = virt_to_phys(&_text); code_resource.end = virt_to_phys(&_etext) - 1; +#ifdef CONFIG_XIP_KERNEL + data_resource.start = virt_to_phys(&_fdata); +#else data_resource.start = virt_to_phys(&_etext); +#endif data_resource.end = virt_to_phys(&_edata) - 1; /* @@ -482,8 +490,18 @@ static inline void resource_init(void) * so we try it repeatedly and let the resource manager * test it. */ +#ifndef CONFIG_XIP_KERNEL request_resource(res, &code_resource); request_resource(res, &data_resource); +#else + if (code_resource.start >= res->start && + code_resource.end <= res->end) + request_resource(res, &code_resource); + if (data_resource.start >= res->start && + data_resource.end <= res->end) + request_resource(res, &data_resource); + +#endif } } diff -u -rN -p linux-2.6.10/arch/mips/kernel/signal-common.h linux-2.6.10-rbtx49/arch/mips/kernel/signal-common.h --- linux-2.6.10/arch/mips/kernel/signal-common.h 1970-01-01 09:00:00.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/signal-common.h 2005-04-22 14:46:18.000000000 +0900 @@ -0,0 +1,147 @@ +/* + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * + * Copyright (C) 1991, 1992 Linus Torvalds + * Copyright (C) 1994 - 2000 Ralf Baechle + * Copyright (C) 1999, 2000 Silicon Graphics, Inc. + */ + +static inline int +setup_sigcontext(struct pt_regs *regs, struct sigcontext *sc) +{ + int err = 0; + struct sigcontext tmpsc; + + err |= __put_user(regs->cp0_epc, &sc->sc_pc); + err |= __put_user(regs->cp0_status, &sc->sc_status); + +#define save_gp_reg(i) do { \ + err |= __put_user(regs->regs[i], &sc->sc_regs[i]); \ +} while(0) + __put_user(0, &sc->sc_regs[0]); save_gp_reg(1); save_gp_reg(2); + save_gp_reg(3); save_gp_reg(4); save_gp_reg(5); save_gp_reg(6); + save_gp_reg(7); save_gp_reg(8); save_gp_reg(9); save_gp_reg(10); + save_gp_reg(11); save_gp_reg(12); save_gp_reg(13); save_gp_reg(14); + save_gp_reg(15); save_gp_reg(16); save_gp_reg(17); save_gp_reg(18); + save_gp_reg(19); save_gp_reg(20); save_gp_reg(21); save_gp_reg(22); + save_gp_reg(23); save_gp_reg(24); save_gp_reg(25); save_gp_reg(26); + save_gp_reg(27); save_gp_reg(28); save_gp_reg(29); save_gp_reg(30); + save_gp_reg(31); +#undef save_gp_reg + + err |= __put_user(regs->hi, &sc->sc_mdhi); + err |= __put_user(regs->lo, &sc->sc_mdlo); + err |= __put_user(regs->cp0_cause, &sc->sc_cause); + err |= __put_user(regs->cp0_badvaddr, &sc->sc_badvaddr); + + err |= __put_user(current->used_math, &sc->sc_used_math); + + if (!current->used_math) + goto out; + + /* + * Save FPU state to signal context. Signal handler will "inherit" + * current FPU state. + */ + preempt_disable(); + + if (!is_fpu_owner()) { + own_fpu(); + restore_fp(current); + } + /* make sure save_fp_context not sleep */ + err |= save_fp_context(&tmpsc); + + preempt_enable(); + + err |= __copy_to_user(&sc->sc_fpregs, &tmpsc.sc_fpregs, + sizeof(tmpsc.sc_fpregs)); + err |= __put_user(tmpsc.sc_fpc_csr, &sc->sc_fpc_csr); + err |= __put_user(tmpsc.sc_fpc_eir, &sc->sc_fpc_eir); + +out: + return err; +} + +static inline int +restore_sigcontext(struct pt_regs *regs, struct sigcontext *sc) +{ + int err = 0; + + /* Always make any pending restarted system calls return -EINTR */ + current_thread_info()->restart_block.fn = do_no_restart_syscall; + + err |= __get_user(regs->cp0_epc, &sc->sc_pc); + err |= __get_user(regs->hi, &sc->sc_mdhi); + err |= __get_user(regs->lo, &sc->sc_mdlo); + +#define restore_gp_reg(i) do { \ + err |= __get_user(regs->regs[i], &sc->sc_regs[i]); \ +} while(0) + restore_gp_reg( 1); restore_gp_reg( 2); restore_gp_reg( 3); + restore_gp_reg( 4); restore_gp_reg( 5); restore_gp_reg( 6); + restore_gp_reg( 7); restore_gp_reg( 8); restore_gp_reg( 9); + restore_gp_reg(10); restore_gp_reg(11); restore_gp_reg(12); + restore_gp_reg(13); restore_gp_reg(14); restore_gp_reg(15); + restore_gp_reg(16); restore_gp_reg(17); restore_gp_reg(18); + restore_gp_reg(19); restore_gp_reg(20); restore_gp_reg(21); + restore_gp_reg(22); restore_gp_reg(23); restore_gp_reg(24); + restore_gp_reg(25); restore_gp_reg(26); restore_gp_reg(27); + restore_gp_reg(28); restore_gp_reg(29); restore_gp_reg(30); + restore_gp_reg(31); +#undef restore_gp_reg + + err |= __get_user(current->used_math, &sc->sc_used_math); + + if (current->used_math) { + /* make sure restore_fp_context not sleep */ + struct sigcontext tmpsc; + err |= __copy_from_user(&tmpsc.sc_fpregs, &sc->sc_fpregs, sizeof(tmpsc.sc_fpregs)); + err |= __get_user(tmpsc.sc_fpc_csr, &sc->sc_fpc_csr); + err |= __get_user(tmpsc.sc_fpc_eir, &sc->sc_fpc_eir); + preempt_disable(); + /* restore fpu context if we have used it before */ + own_fpu(); + err |= restore_fp_context(&tmpsc); + } else { + /* signal handler may have used FPU. Give it up. */ + preempt_disable(); + lose_fpu(); + } + + preempt_enable(); + + return err; +} + +/* + * Determine which stack to use.. + */ +extern inline void * +get_sigframe(struct k_sigaction *ka, struct pt_regs *regs, size_t frame_size) +{ + unsigned long sp, almask; + + /* Default to using normal stack */ + sp = regs->regs[29]; + + /* + * FPU emulator may have it's own trampoline active just + * above the user stack, 16-bytes before the next lowest + * 16 byte boundary. Try to avoid trashing it. + */ + sp -= 32; + + /* This is the X/Open sanctioned signal stack switching. */ + if ((ka->sa.sa_flags & SA_ONSTACK) && (sas_ss_flags (sp) == 0)) + sp = current->sas_ss_sp + current->sas_ss_size; + + if (PLAT_TRAMPOLINE_STUFF_LINE) + almask = ~(PLAT_TRAMPOLINE_STUFF_LINE - 1); + else + almask = ALMASK; + + return (void *)((sp - frame_size) & almask); +} diff -u -rN -p linux-2.6.10/arch/mips/kernel/signal.c linux-2.6.10-rbtx49/arch/mips/kernel/signal.c --- linux-2.6.10/arch/mips/kernel/signal.c 2004-12-25 06:35:59.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/signal.c 2005-04-22 14:46:18.000000000 +0900 @@ -29,12 +29,15 @@ #include #include #include +#include + +#include "signal-common.h" #define DEBUG_SIG 0 #define _BLOCKABLE (~(sigmask(SIGKILL) | sigmask(SIGSTOP))) -extern asmlinkage int do_signal(sigset_t *oldset, struct pt_regs *regs); +static int do_signal(sigset_t *oldset, struct pt_regs *regs); /* * Atomically swap in the new signal mask, and wait for a signal. @@ -152,51 +155,6 @@ asmlinkage int sys_sigaltstack(nabi_no_r return do_sigaltstack(uss, uoss, usp); } -asmlinkage int restore_sigcontext(struct pt_regs *regs, struct sigcontext *sc) -{ - int err = 0; - - /* Always make any pending restarted system calls return -EINTR */ - current_thread_info()->restart_block.fn = do_no_restart_syscall; - - err |= __get_user(regs->cp0_epc, &sc->sc_pc); - err |= __get_user(regs->hi, &sc->sc_mdhi); - err |= __get_user(regs->lo, &sc->sc_mdlo); - -#define restore_gp_reg(i) do { \ - err |= __get_user(regs->regs[i], &sc->sc_regs[i]); \ -} while(0) - restore_gp_reg( 1); restore_gp_reg( 2); restore_gp_reg( 3); - restore_gp_reg( 4); restore_gp_reg( 5); restore_gp_reg( 6); - restore_gp_reg( 7); restore_gp_reg( 8); restore_gp_reg( 9); - restore_gp_reg(10); restore_gp_reg(11); restore_gp_reg(12); - restore_gp_reg(13); restore_gp_reg(14); restore_gp_reg(15); - restore_gp_reg(16); restore_gp_reg(17); restore_gp_reg(18); - restore_gp_reg(19); restore_gp_reg(20); restore_gp_reg(21); - restore_gp_reg(22); restore_gp_reg(23); restore_gp_reg(24); - restore_gp_reg(25); restore_gp_reg(26); restore_gp_reg(27); - restore_gp_reg(28); restore_gp_reg(29); restore_gp_reg(30); - restore_gp_reg(31); -#undef restore_gp_reg - - err |= __get_user(current->used_math, &sc->sc_used_math); - - preempt_disable(); - - if (current->used_math) { - /* restore fpu context if we have used it before */ - own_fpu(); - err |= restore_fp_context(sc); - } else { - /* signal handler may have used FPU. Give it up. */ - lose_fpu(); - } - - preempt_enable(); - - return err; -} - #if PLAT_TRAMPOLINE_STUFF_LINE #define __tramp __attribute__((aligned(PLAT_TRAMPOLINE_STUFF_LINE))) #else @@ -220,7 +178,9 @@ struct rt_sigframe { }; #ifdef CONFIG_TRAD_SIGNALS -asmlinkage void sys_sigreturn(struct pt_regs regs) +save_static_function(sys_sigreturn); +__attribute_used__ noinline static void +_sys_sigreturn(nabi_no_regargs struct pt_regs regs) { struct sigframe *frame; sigset_t blocked; @@ -257,7 +217,9 @@ badframe: } #endif -asmlinkage void sys_rt_sigreturn(nabi_no_regargs struct pt_regs regs) +save_static_function(sys_rt_sigreturn); +__attribute_used__ noinline static void +_sys_rt_sigreturn(nabi_no_regargs struct pt_regs regs) { struct rt_sigframe *frame; sigset_t set; @@ -298,88 +260,15 @@ badframe: force_sig(SIGSEGV, current); } -inline int setup_sigcontext(struct pt_regs *regs, struct sigcontext *sc) -{ - int err = 0; - - err |= __put_user(regs->cp0_epc, &sc->sc_pc); - err |= __put_user(regs->cp0_status, &sc->sc_status); - -#define save_gp_reg(i) do { \ - err |= __put_user(regs->regs[i], &sc->sc_regs[i]); \ -} while(0) - __put_user(0, &sc->sc_regs[0]); save_gp_reg(1); save_gp_reg(2); - save_gp_reg(3); save_gp_reg(4); save_gp_reg(5); save_gp_reg(6); - save_gp_reg(7); save_gp_reg(8); save_gp_reg(9); save_gp_reg(10); - save_gp_reg(11); save_gp_reg(12); save_gp_reg(13); save_gp_reg(14); - save_gp_reg(15); save_gp_reg(16); save_gp_reg(17); save_gp_reg(18); - save_gp_reg(19); save_gp_reg(20); save_gp_reg(21); save_gp_reg(22); - save_gp_reg(23); save_gp_reg(24); save_gp_reg(25); save_gp_reg(26); - save_gp_reg(27); save_gp_reg(28); save_gp_reg(29); save_gp_reg(30); - save_gp_reg(31); -#undef save_gp_reg - - err |= __put_user(regs->hi, &sc->sc_mdhi); - err |= __put_user(regs->lo, &sc->sc_mdlo); - err |= __put_user(regs->cp0_cause, &sc->sc_cause); - err |= __put_user(regs->cp0_badvaddr, &sc->sc_badvaddr); - - err |= __put_user(current->used_math, &sc->sc_used_math); - - if (!current->used_math) - goto out; - - /* - * Save FPU state to signal context. Signal handler will "inherit" - * current FPU state. - */ - preempt_disable(); - - if (!is_fpu_owner()) { - own_fpu(); - restore_fp(current); - } - err |= save_fp_context(sc); - - preempt_enable(); - -out: - return err; -} - -/* - * Determine which stack to use.. - */ -static inline void *get_sigframe(struct k_sigaction *ka, struct pt_regs *regs, - size_t frame_size) -{ - unsigned long sp, almask; - - /* Default to using normal stack */ - sp = regs->regs[29]; - - /* - * FPU emulator may have it's own trampoline active just - * above the user stack, 16-bytes before the next lowest - * 16 byte boundary. Try to avoid trashing it. - */ - sp -= 32; - - /* This is the X/Open sanctioned signal stack switching. */ - if ((ka->sa.sa_flags & SA_ONSTACK) && (sas_ss_flags (sp) == 0)) - sp = current->sas_ss_sp + current->sas_ss_size; - - if (PLAT_TRAMPOLINE_STUFF_LINE) - almask = ~(PLAT_TRAMPOLINE_STUFF_LINE - 1); - else - almask = ALMASK; - - return (void *)((sp - frame_size) & ~(PLAT_TRAMPOLINE_STUFF_LINE - 1)); -} - +#define CHECK_SETUP_FRAME_FAILURE #ifdef CONFIG_TRAD_SIGNALS +#ifdef CHECK_SETUP_FRAME_FAILURE +static int inline setup_frame(struct k_sigaction * ka, struct pt_regs *regs, + int signr, sigset_t *set) +#else static void inline setup_frame(struct k_sigaction * ka, struct pt_regs *regs, int signr, sigset_t *set) +#endif { struct sigframe *frame; int err = 0; @@ -395,8 +284,7 @@ static void inline setup_frame(struct k_ * syscall */ if (PLAT_TRAMPOLINE_STUFF_LINE) - __builtin_memset(frame->sf_code, '0', - PLAT_TRAMPOLINE_STUFF_LINE); + __clear_user(frame->sf_code, PLAT_TRAMPOLINE_STUFF_LINE); err |= __put_user(0x24020000 + __NR_sigreturn, frame->sf_code + 0); err |= __put_user(0x0000000c , frame->sf_code + 1); flush_cache_sigtramp((unsigned long) frame->sf_code); @@ -428,15 +316,27 @@ static void inline setup_frame(struct k_ current->comm, current->pid, frame, regs->cp0_epc, frame->regs[31]); #endif +#ifdef CHECK_SETUP_FRAME_FAILURE + return 0; +#else return; +#endif give_sigsegv: force_sigsegv(signr, current); +#ifdef CHECK_SETUP_FRAME_FAILURE + return SIGSEGV; +#endif } #endif +#ifdef CHECK_SETUP_FRAME_FAILURE +static int inline setup_rt_frame(struct k_sigaction * ka, struct pt_regs *regs, + int signr, sigset_t *set, siginfo_t *info) +#else static void inline setup_rt_frame(struct k_sigaction * ka, struct pt_regs *regs, int signr, sigset_t *set, siginfo_t *info) +#endif { struct rt_sigframe *frame; int err = 0; @@ -452,8 +352,7 @@ static void inline setup_rt_frame(struct * syscall */ if (PLAT_TRAMPOLINE_STUFF_LINE) - __builtin_memset(frame->rs_code, '0', - PLAT_TRAMPOLINE_STUFF_LINE); + __clear_user(frame->rs_code, PLAT_TRAMPOLINE_STUFF_LINE); err |= __put_user(0x24020000 + __NR_rt_sigreturn, frame->rs_code + 0); err |= __put_user(0x0000000c , frame->rs_code + 1); flush_cache_sigtramp((unsigned long) frame->rs_code); @@ -498,18 +397,34 @@ static void inline setup_rt_frame(struct current->comm, current->pid, frame, regs->cp0_epc, regs->regs[31]); #endif +#ifdef CHECK_SETUP_FRAME_FAILURE + return 0; +#else return; +#endif give_sigsegv: force_sigsegv(signr, current); +#ifdef CHECK_SETUP_FRAME_FAILURE + return SIGSEGV; +#endif } extern void setup_rt_frame_n32(struct k_sigaction * ka, struct pt_regs *regs, int signr, sigset_t *set, siginfo_t *info); +#ifdef CHECK_SETUP_FRAME_FAILURE +static inline int handle_signal(unsigned long sig, siginfo_t *info, + struct k_sigaction *ka, sigset_t *oldset, struct pt_regs *regs) +#else static inline void handle_signal(unsigned long sig, siginfo_t *info, struct k_sigaction *ka, sigset_t *oldset, struct pt_regs *regs) +#endif { +#ifdef CHECK_SETUP_FRAME_FAILURE + int newsig = 0; +#endif + switch(regs->regs[0]) { case ERESTART_RESTARTBLOCK: case ERESTARTNOHAND: @@ -538,12 +453,25 @@ static inline void handle_signal(unsigne setup_rt_frame_n32 (ka, regs, sig, oldset, info); else #endif +#ifdef CHECK_SETUP_FRAME_FAILURE + newsig = +#endif setup_rt_frame(ka, regs, sig, oldset, info); } #ifdef CONFIG_TRAD_SIGNALS else +#ifdef CHECK_SETUP_FRAME_FAILURE + newsig = +#endif setup_frame(ka, regs, sig, oldset); #endif +#ifdef CHECK_SETUP_FRAME_FAILURE + if (newsig) { + printk("Can not setup signal frame for %s (pc 0x%lx signal %ld).\n", + current->comm, regs->cp0_epc, sig); + return newsig; + } +#endif if (!(ka->sa.sa_flags & SA_NODEFER)) { spin_lock_irq(¤t->sighand->siglock); @@ -552,12 +480,15 @@ static inline void handle_signal(unsigne recalc_sigpending(); spin_unlock_irq(¤t->sighand->siglock); } +#ifdef CHECK_SETUP_FRAME_FAILURE + return 0; +#endif } extern int do_signal32(sigset_t *oldset, struct pt_regs *regs); extern int do_irix_signal(sigset_t *oldset, struct pt_regs *regs); -asmlinkage int do_signal(sigset_t *oldset, struct pt_regs *regs) +static int do_signal(sigset_t *oldset, struct pt_regs *regs) { struct k_sigaction ka; siginfo_t info; @@ -585,9 +516,17 @@ asmlinkage int do_signal(sigset_t *oldse if (!oldset) oldset = ¤t->blocked; +#ifdef CHECK_SETUP_FRAME_FAILURE + checkagain: +#endif signr = get_signal_to_deliver(&info, &ka, regs, NULL); if (signr > 0) { +#ifdef CHECK_SETUP_FRAME_FAILURE + if (handle_signal(signr, &info, &ka, oldset, regs)) + goto checkagain; /* another signal queued. */ +#else handle_signal(signr, &info, &ka, oldset, regs); +#endif return 1; } @@ -613,8 +552,6 @@ no_signal: return 0; } -extern int do_irix_signal(sigset_t *oldset, struct pt_regs *regs); - /* * notification of userspace execution resumption * - triggered by current->work.notify_resume diff -u -rN -p linux-2.6.10/arch/mips/kernel/syscall.c linux-2.6.10-rbtx49/arch/mips/kernel/syscall.c --- linux-2.6.10/arch/mips/kernel/syscall.c 2004-12-25 06:35:24.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/syscall.c 2005-04-22 14:46:18.000000000 +0900 @@ -116,7 +116,7 @@ unsigned long arch_get_unmapped_area(str } /* common code for old and new mmaps */ -static inline long +static inline unsigned long do_mmap2(unsigned long addr, unsigned long len, unsigned long prot, unsigned long flags, unsigned long fd, unsigned long pgoff) { @@ -140,8 +140,9 @@ out: return error; } -asmlinkage unsigned long old_mmap(unsigned long addr, size_t len, int prot, - int flags, int fd, off_t offset) +asmlinkage unsigned long +old_mmap(unsigned long addr, unsigned long len, int prot, + int flags, int fd, off_t offset) { unsigned long result; @@ -155,7 +156,7 @@ out: return result; } -asmlinkage long +asmlinkage unsigned long sys_mmap2(unsigned long addr, unsigned long len, unsigned long prot, unsigned long flags, unsigned long fd, unsigned long pgoff) { diff -u -rN -p linux-2.6.10/arch/mips/kernel/traps.c linux-2.6.10-rbtx49/arch/mips/kernel/traps.c --- linux-2.6.10/arch/mips/kernel/traps.c 2004-12-25 06:34:32.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/traps.c 2005-04-22 14:46:18.000000000 +0900 @@ -38,12 +38,9 @@ #include #include -extern asmlinkage void handle_mod(void); +extern asmlinkage void handle_tlbm(void); extern asmlinkage void handle_tlbl(void); extern asmlinkage void handle_tlbs(void); -extern asmlinkage void __xtlb_mod(void); -extern asmlinkage void __xtlb_tlbl(void); -extern asmlinkage void __xtlb_tlbs(void); extern asmlinkage void handle_adel(void); extern asmlinkage void handle_ades(void); extern asmlinkage void handle_ibe(void); @@ -82,7 +79,12 @@ void show_stack(struct task_struct *task long stackdata; int i; - sp = sp ? sp : (unsigned long *) &sp; + if (!sp) { + if (task && task != current) + sp = (unsigned long *) task->thread.reg29; + else + sp = (unsigned long *) &sp; + } printk("Stack :"); i = 0; @@ -110,8 +112,12 @@ void show_trace(struct task_struct *task const int field = 2 * sizeof(unsigned long); unsigned long addr; - if (!stack) - stack = (unsigned long*)&stack; + if (!stack) { + if (task && task != current) + stack = (unsigned long *) task->thread.reg29; + else + stack = (unsigned long *) &stack; + } printk("Call Trace:"); #ifdef CONFIG_KALLSYMS @@ -506,6 +512,14 @@ asmlinkage void do_fpe(struct pt_regs *r preempt_disable(); +#ifdef CONFIG_PREEMPT + if (!is_fpu_owner()) { + /* We might lose fpu before disabling preempt... */ + own_fpu(); + BUG_ON(!current->used_math); + restore_fp(current); + } +#endif /* * Unimplemented operation exception. If we've got the full * software emulator on-board, let's use it... @@ -517,10 +531,13 @@ asmlinkage void do_fpe(struct pt_regs *r * a bit extreme for what should be an infrequent event. */ save_fp(current); + /* Ensure 'resume' not overwrite saved fp context again. */ + lose_fpu(); /* Run the emulator */ sig = fpu_emulator_cop1Handler (0, regs, ¤t->thread.fpu.soft); + own_fpu(); /* Using the FPU again. */ /* * We can't allow the emulated instruction to leave any of @@ -1001,16 +1018,10 @@ void __init trap_init(void) if (board_be_init) board_be_init(); -#ifdef CONFIG_MIPS32 - set_except_vector(1, handle_mod); + set_except_vector(1, handle_tlbm); set_except_vector(2, handle_tlbl); set_except_vector(3, handle_tlbs); -#endif -#ifdef CONFIG_MIPS64 - set_except_vector(1, __xtlb_mod); - set_except_vector(2, __xtlb_tlbl); - set_except_vector(3, __xtlb_tlbs); -#endif + set_except_vector(4, handle_adel); set_except_vector(5, handle_ades); @@ -1047,7 +1058,7 @@ void __init trap_init(void) * unaligned ldc1/sdc1 exception. The handlers have not been * written yet. Well, anyway there is no R6000 machine on the * current list of targets for Linux/MIPS. - * (Duh, crap, there is someone with a tripple R6k machine) + * (Duh, crap, there is someone with a triple R6k machine) */ //set_except_vector(14, handle_mc); //set_except_vector(15, handle_ndc); diff -u -rN -p linux-2.6.10/arch/mips/kernel/vmlinux.lds.S linux-2.6.10-rbtx49/arch/mips/kernel/vmlinux.lds.S --- linux-2.6.10/arch/mips/kernel/vmlinux.lds.S 2004-12-25 06:34:30.000000000 +0900 +++ linux-2.6.10-rbtx49/arch/mips/kernel/vmlinux.lds.S 2005-04-22 14:46:18.000000000 +0900 @@ -8,6 +8,7 @@ ENTRY(kernel_entry) jiffies = JIFFIES; SECTIONS { +#ifndef CONFIG_XIP_KERNEL #ifdef CONFIG_BOOT_ELF64 /* Read-only sections, merged into text segment: */ /* . = 0xc000000000000000; */ @@ -129,6 +130,107 @@ SECTIONS . = ALIGN(4096); __init_end = .; /* freed after init ends here */ +#else /* CONFIG_XIP_KERNEL */ + . = LOADADDR; + /* read-only */ + .init : { + . = ALIGN(4096); /* Init code and data */ + __init_begin = .; + _sinittext = .; + *(.init.text) + _einittext = .; + . = ALIGN(16); + __setup_start = .; + *(.init.setup) + __setup_end = .; + + __earlyinitcall_start = .; + *(.initcall.early1.init) + __earlyinitcall_end = .; + __initcall_start = .; + *(.initcall1.init) + *(.initcall2.init) + *(.initcall3.init) + *(.initcall4.init) + *(.initcall5.init) + *(.initcall6.init) + *(.initcall7.init) + __initcall_end = .; + __con_initcall_start = .; + *(.con_initcall.init) + __con_initcall_end = .; + . = ALIGN(4096); + __initramfs_start = .; + *(.init.ramfs) + __initramfs_end = .; + . = ALIGN(4096); + __init_end = .; + } + + .text : { + _text = .; /* Text and read-only data */ + *(.text) + SCHED_TEXT + LOCK_TEXT + *(.fixup) + *(.gnu.warning) + } + + SECURITY_INIT + + . = ALIGN(16); /* Exception table */ + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + __start___dbe_table = .; /* Exception table for data bus errors */ + __dbe_table : { *(__dbe_table) } + __stop___dbe_table = .; + + RODATA + _etext = .; /* End of text section */ + + /* writeable */ + . = DATAADDR ; + _sdata = . ; + . = . ; + .data : { /* Data */ + _fdata = . ; + . = . + DATAOFFSET; /* for CONFIG_MAPPED_KERNEL */ + *(.data.init_tas