RPi Cases

From eLinux.org
Jump to: navigation, search

Back to RPi Hardware Basic Setup.

As yet, the foundation does not provide cases for the Raspberry Pi. The small form factor or low power draw however, allow you to put it in almost everything.


RaspPi.png Back to the Hub

Hardware & Peripherals:

Hardware - detailed information about the Raspberry Pi boards.

Hardware History - guide to the Raspberry Pi models.

Low-level Peripherals - using the GPIO and other connectors.

Expansion Boards - GPIO plug-in boards providing additional functionality.

Screens - attaching a screen to the Raspberry Pi.

Cases - lots of nice cases to protect the Raspberry Pi.

Other Peripherals - all sorts of peripherals used with the Raspberry Pi.

Mechatronics Art Aluminum Case

This Raspberry Pi 3 Case is acting as a passive heat sink that improves the single board computer performances. Check out the Raspberry Pi 3 Aluminum Case.

Secret book case

Secret book case for Raspberry Pi

This case can be made from any book. It is home made so you can choose any cover, format, etc. When put next to other cables, the trick is perfect. Cables connected to the Raspberry Pi are barely distinguishable from the other cables and you now have a perfectly hidden computer.

Instructions to make a secret book case for Raspberry Pi

Lego Case

The Rpi Lego case, designed by forum user eric_baird

I just had a go at knocking up a quick Lego case prototype. Since I don't know the metrics of all the connections, it's a bit of a "proof of concept" right now, but since's it's not exactly difficult to take out any offending side-pieces and move them if they're in the way of a beloved connector, I'm assuming that this isn't a big deal.

Also, because of the thin side-walls, a bit of additional hacksawing or dremeling shouldn't be too difficult.

I've limited myself to only using pieces that are currently available from Lego's "Pick a Brick" shop, in red. :)

I've tried to fit everything into an 8*12 grid footprint, which will hopefully fit … but I don't have the specs of the thickness of the thin wall-pieces, so no guarantees. One thing that might screw things up is the height of the board's connectors: I don't know whether they'll all fit within the upper and lower lip of the side-wall pieces. If the board's "USB port stack" is too high, I guess the "roof" could be raised by a tile or two.

I knocked it up with Lego's Digital Designer program (free download from their site). The critical Lego piece is the repeated hollowed-out "side wall" ("[") brick ("wall element 1*2*2, w. window"), which you'll find on LDD's parts palette behind the little "door" symbol, or under the Pick a Brick page, as element #4507686, design #60032 (red), cost 8 pence each.

Feel free to hack, mangle or otherwise rework.

Download the Lego Digital Designer file for this case

Lego Case 2

Another Rpi Lego case, designed by forum user kimondo

I had a bit of a play in lego designer with the idea of a vertical case – the USB / ethernet would emerge from the top, and the power usb would be on the bottom – possibly using a right angled usb connector. It's possible to alter the sides to allow for gaps for the various bits that stick out. There are lots of transparent bricks available – also includes a 2 x 2 brick to stick the raspberry pi sticker on.

ICEberg Case V3 for Raspberry Pi

  1. First Case Aluminium with direct Coolling for CPU & LAN chipset
  2. Heat transfer with Silicon Thermal Pad
  3. Light LED Guide on the side (Option)
  4. 100% Aluminium machined CNC
  5. Case Design Pro
  6. GPU port available
  7. Upgrade with Vesa Mount 75x75mm & 100x100mm (Option)
  8. Gloss finish
  9. Rubber foot
  10. Option with or without logo (ICEberg/Raspberry)
A rendering of the case made by Moovika
ICEberg V3
ICEberg V3
New logo engraving 2013
ICEberg V3
Exploded View ICEberg case
ICEberg V3 Heat Transfer !
ICEberg V3 Heat Transfer 2
ICEberg V3 with Vesa Mount (Option)
Light-led-guide Front

More information on BLOG ICEberg Case

New Video V3 on youtube ICEberg Case V3 Aluminium for Raspberry PI

Shop Moovika Shop Ebay

Raspi ALU Case for Raspberry Pi

Ben has published full details on the creation of this nice Raspberry Pi aluminium case, the board is shielded and protected from metal conductivity with an internal PVC base. Looks like a professional case for an headless computer used as a small server.


Raspi.alu.case.jpg Raspi.alu.case.2.jpg

This unique case has an integrated USB hub to expand Raspberry usb ports and take power source from it as well, full disclosure and details are also reported there. This is a low budget case built from scratch with recycled parts and spare PVC and aluminium sheets

More infos on Moebius website: http://moebiuslinux.sourceforge.net

Marco Alici Case for Raspberry Pi

Marco Alici, Italian Design Engineer, has designed this well appreciated clean enclosure to host the computer:


A rendering of the case made by MarcoA
Another rendering made using Blender and Yafaray
A stackable version of the enclosure
Raspberry Pi computer mounted into the first version of the enclosure 3D printed by Shapeways

This case is available for 3D printing here on Shapeways. Everyone can buy it directly over there.

More infos on Marco's blog: http://marcoalici.wordpress.com

Raspberry Pi Case made from a single sheet of polypropylene (PP)

Raspberry Pi case from IP Adelt

Strong case cut from a single sheet of polypropylene using a cutting plotter (video), made in Germany by IP Adelt. Here's the story. Sold via RaspiProjekt.de to the whole world - in a simple envelope!

Review of the Beta version of the case on the PiPod blog

Printable Mylar Sheet/cardboard Fold-up Case

"tzj" Printable Mylar sheet case

RaspberryPi.org forum user "eric_baird" thought of printing an outline of the walls of a case on a Mylar overhead projector (OHP) sheet or cardboard that could then be cut out and folded into a case. Multiple users have since drawn such cases that can be printed on a Mylar sheet, thick paper, card stock, cardboard. The printed parts can be cut with a sharp knife or scissors and then folded/assembled into the case.

Multiple models are available:

The foldable case from "tzj" (currently based on the model B beta board).

The foldable case from "alexisread" originally posted here.

The foldable case from "Andrew K" is based on measurements of an actual Raspberry Pi model B and fits snugly.

The foldable case from Thomas Mueller is (arguably) a bit more stylish. It stays closed without glue, and can be re-opened.

A printable case for the Raspberry Pi 3 Model B (no glue necessary; best printed on cardboard): as PDF or (editable) SVG. Also available with the Raspberry logo on the top (PDF, SVG).

Laser-cut Clear Acrylic Case

eBay UK seller guitarreriacom is offering a laser-cut clear acrylic case.

Laser-cut Clear Acrylic Case on eBay
Laser-cut Clear Acrylic Case on eBay

Adafruit Pi Box

BRAMBLE Pi - Laser-cut Finger Jointed Wooden Case

Bitcrafts is offering a finger-jointed wooden case for the Raspberry Pi.

  • Laser cut from high quality birch plywood and engraved with a circuit diagram design.
  • Comes as a kit, easy to assemble. NO glue or screws required.
  • New design! Includes holes for screwing in version2 boards.
Laser-cut finger-jointed wooden case.
Comes as a kit, easy to assemble. NO glue or screws required.

Custom engraved Bramble Pi case

Bitcrafts also offers a Custom engraved Bramble Pi case for the Raspberry Pi.

Virtually any motif can be engraved!
Linux's Tux.
Ventilation ports are possible on the bottom plate (ad top) but also on both long sides.
Ventilation ports are possible on the bottom plate (ad top) but also on both long sides.


Bramble Pi3 - Raspberry Pi case with GPIO-cable slot & space for IDC connector.

  • Slot for GPIO-cable.
  • An IDC female connector can be used but without the strain relief.
  • Buy from Bitcrafts.
Circuit schematic engraved!
With a slot for a GPIO cable.

BrambleX - HTPC XBMC OpenElec Raspbmc Xbian case for Raspberry Pi

BrambleX on sale from Bitcrafts. Pick your favourite media center distro!

Pick your favourite from XBMC, OpenElec, Raspbmc or Xbian!

Raspberry Pi Board B Enclosure

solidworks prototype

A solidworks concept from http://solidworksbootcamp.com/raspberry-pi-board-b-enclosure/

Raspberry Pi air case

shape model

http://www.shapeways.com/model/434919/ and this is the video

Raspberry Pi fimo case

fimo cover

The bijoux artist Annarella gioelli has made her versione of case for raspberry pi usign fimo (a kind of polymer clay), there are a tutorial and a video tutorial

ModMyPi Modular Case

Our new deluxe Raspberry Pi 2/3 Model B case is a fully customisable and adaptable modular unit aimed to suit a range of Raspberry Pi applications. Designed with a stealth look and integrated LED lights pipes, it’s the perfect accessory to any Raspberry Pi enthusiast’s tool kit!

ModMyPi Pi Zero Case

We're pleased to introduce our new range of professional, fully injection moulded Raspberry Pi Zero cases! As with all our injection moulded cases, they're designed to optimise protection whilst maintaining device useability. Our Pi Zero cases consist of a 3-Part clip together construction with Micro SD card cover and embossed Raspberry Pi Foundation logo, which acts as a ventilation point for heat extraction.

ModMyPi Pi Zero Layer Case

We're proud to introduce ModMyPi's new Pi Zero Case! Made with our trademark stealth-matte black acrylic, and accented with clear (to leave the good bits visible), the case itself is constructed of 4 layers. We've put the "ooh la la" back in lazoohlala cutting with this one, recessing the nuts and bolts to give a super sleek slim profile with no bumpy bits.

Short Crust Case

Short Crust Case for Raspberry Pi

Short Crust is a case for the Raspberry Pi which is designed to look attractive, be easy to use and be adaptable for different types of projects. It has a simple and elegant look and is designed to be used with a variety of projects – and look great whilst doing so. It features a very easy to use “snap in place” mounting method for the Raspberry Pi which keeps it very secure, but easy to remove from the case when you want to. It uses a simple flat top cover, which makes it extremely easy for you to customise the case yourself – with different colours or materials. Additionally due to the brass screw thread mounting points you can customise the case in other ways – with extensions and stacking of components above the Raspberry Pi.

Cable management becomes a breeze with the Short Crust case, and it keeps your SD card very well protected due to its extended length.

Features include:

- Simple, clean design with easy access to all inputs and outputs.

- MicroUSB power relocated to the same side as USB and Ethernet ports for tidy cable management.

- Raspberry Pi snaps into place – secure, no rattling, and easily removable.

- Internal mounting holes for attaching the case directly to your project / prototype.

- Removable cover for hiding the RCA and 3.5mm audio ports when not in use.

- ‘Smoke’ tinted acrylic covers for a clean look while leaving the Raspberry Pi visible.

- Simple, flat covers to make it easier for you to create your own and customize the look of the case.

- Open top design with brass screw thread mounting points to allow user made, custom design extensions and stacking of components above the Raspberry Pi.

- SD card doesn’t protrude from the case – looks attractive, easily removable, protected from accidental knocks.

There are some short assembly instructions and videos for you which can be viewed at the following link: Assembly Instructions

You can purchase one from the Pi Supply shop here - http://www.pi-supply.com/product/shortcrust-perfect-base-raspberry-pi/

Berry Box - The Lego compatible, transparent case for the Raspberry Pi

Berry Box

this is a project to make a case compatible with lego components, there's a video

RaspBerry Slice

RaspBerry Slice

this is a project of the designer Brian Garvey, there a page and a video

Raspberry Pi Cover - SK Pang electronics

Developed in-house and manufactured in the UK. A range of laser cut acrylic covers for the Raspberry Pi. Link

RaspBerry Cover
RaspBerry Cover with Breadboard Area
RaspBerry Cover with Breadboard Area

Pi-Stack Raspberry Pi enclosure

RaspBerry Cover

Developed in-house and manufactured in the UK. One of a range of compatible acrylic products designed exclusively for the Raspberry Pi. While everyone else seems determined to "cover up his beauty from the world", the Pi-Stack exposes the Raspberry Pi elegantly from all 4 sides. Unlike some of the other designs the makers claim that this also allows access to all the GPIO pins. Currently available in "Gold", "Silver" and black with 10mm acrylic base and top. Currently sold in USA, Canada and Australia as well as the UK, via Ebay.

Here's a link to a video showing how the Pi-STACK can be cable managed to reduce the maze of wires normally hanging off the Raspberry Pi management

RepRap friendly cover for Raspberry Pi

RepRap Pi Cover

The Rep-Rap we have is not very reliable and is only really able to produce basic designs so this is a 6 part case that has to be glued together. There are 6 stl files here with construction notes.

Mega Drive / Genesis Case for Raspberry Pi

Mega Drive / Genesis Case by osholt

The design was thought up by osholt on the evening after receiving his Pi. The case is strictly DIY and an Instructable for it can be found at the Instructables website. The case is well suited to Green enthusiasts as it can easily be made with only reused or reclaimed parts as well as to emulation enthusiasts and to users with limited resources and design skill (you only need to know how to use a screwdriver to make the whole thing).


Our intention is to design a case for B model and provide that model of a functional protection, which all of us we will enjoy if you help me to achieve my objectives with your cooperation.

You can support al RPIBOX project at lanzanos.com. For more information visit at oficial forum and rpibox web RPIBOX black case RPIBOX white case


The RaspBox, a minimalistic design.

The RaspBox is made of two acrylic glass plates and four metallic spacers. All parts are hold together by eight screws. This minimalistic design comes from the Swiss company Yoctopuce. Originally, the RaspBox was just a pet-project, but as it was very appreciated within the company staff, the decision was made to bring it to the public. The design itself has been released under a Creative Commons Attribution-ShareAlike 3.0 License and can be downloaded from the product page. The finished product is also available from the Yoctopuce shop.

Known / Reliably 3D printable cases Cases

Two cases have been successfully printed on home 3D Printers so far. Both offer vented lid options for heat concerns. The main difference is one allows GPIO pin access for a cable, the other is either vented or entirely open on top.

Design One

Printed case with GPIO access
Raspi gpio uncovered.jpg
Raspi gpio vent covered.jpg

Design Two, as designed in Inventor and printed on a variety of printers.

Printed case
RasPi rear.jpg
RasPi cover.jpg
RasPi vent.jpg

Tape Case

Transparent cases for raspberry can be created using the case of a cassette tape. Simply drill and cut the holes that are needed into the case using a dremel.

Second version of the Tape Case

more images of the tape case

DiscPi Case

Easy DIY case made from a CD and plastic CD protectors.

DiscPi case

More images

An 4€ RPi case

When having an RPi for 30€, buying a 15€ case is quit expensive. I decided to create this case. You just need :

  1. An 21x29.7 Art foam Cardboard
  2. Cutter
  3. Glues : sticker and gel

How to :

  1. Print the templates with the right scale
  2. Validate the sizes
  3. Glue the template on the board using the glue sticker
  4. Cut, assemble and glue using the glue gel
  5. If the RPi will stay powered for a long time. A few vent holes could be added

Final touch:

  1. Print a Raspberry Pi logo and glue it

The libreCad template files could be downloaded : File:Raspberry-pi-3mm-foamboard-case.dxf and the File:Raspberry-pi-3mm-foamboard-case-strips.dxf

The 3d views of the case, thank you Hervé C. for this nice design :






Pibow Case

Made up of colorful layers sandwiched together between clear acrylic. Well received by the folks at the RaspberryPi foundation.

LCD Monitor Mount

PI LCD Monitor Mount by PC Supplies

PI LCD Mount from PC Supplies Limited (eBay), VESA 100 x 100 Standard Mount, Requires the 4xVESA Holes on your Monitor, Maybe not compatible if your monitor uses the VESA for the Base / Stand, Not compatible if you are already wall mounting your LCD Screen, Wafer Design, Motherboard is sandwiched between 2 wafers of clear shiny acrylic! Designed for Raspberry PI, Secured using 8 x M3 Nuts, Hex Spacers & Screws to allow you to build and unbuild, 4xM4 Spacers and 4xM4 Screws for the VESA Mounting. GPIO Compatible

Wafer Case

Wafer by PC Supplies

PI Wafer Case from PC Supplies Limited, Wafer Design, Motherboard is sandwiched between 2 wafers of clear shiny acrylic!

Available from Amazon UK, Shipping throughout Europe Amazon UK

PI Box Case

Pi Box by PC Supplies

Pi Box is the new Professional Case from PC Supplies Limited, Covers all sides of the motherboard for the ultimate protection. Unique Fit-together design with custom supplied 'PI Clips' Allows Access to SD Port / USB / Ethernet / Audio / Video / HDMI and PSU , No screws! and NO elastic bands! - "A true PRO design"

Available from Amazon UK, Shipping throughout Europe Amazon UK

PI Sandwich Case

BUD PI Sandwich

BUD Industries is Proud to introduce The PI Sandwich Enclosure, designed for use with the Raspberry Pi microcomputer (not supplied) and to accommodate changes in component location on the board as well as the potential addition of components . The enclosures provide protection, flexibility and ease of access to all components with quick snap-in installation. This rectangular version is open on all four sides for direct access.

more details

I bought two of these at Jameco Electronics in Belmont, CA for $7 each. It's okay, but the board is not held tightly in place. You wand to plug in cables and the SD card before the board is snapped into place because the board will pop out otherwise, and could break the plastic pieces. The two sides of the case are identical. You have to gently rock the sides back and forth to disassemble the case without breaking anything.

Simple sandwich case

Sandwich case

Like me, most people do not have access to precision cutting tools like laser cutters. This makes it's rather difficult to do some of the intricate laser-cut case designs at home. So I decided to go with a simple sandwich case.

The case consists of:

  • Two sheets of 75x120 mm polycarbonate
  • Twelve 12 mm M5 countersunk hex screws
  • Six 25 mm round spacers

The spacers have a notch at 6 mm which holds the board in place between the sheets of polycarbonate. Sadly, my design isn't optimal since one of the spacers covers the GPIO pins.

This isn't the most beautiful case but I hope it inspires people to be creative and build their own case instead of just buying one. Building is fun!

Aluminum Engraved Case by Barch Designs

Raspberry-pi-case LED3.jpg Raspberry-pi-case wired1.jpg Raspberry-pi-case bottom cs.jpg Raspberry-pi-case GPIO3.jpg Raspberry-pi-case assembly4.jpg Raspberry-pi-case assembly3.jpg

CNC Machined from Billet Aluminum. Mounting Holes in Bottom. Acts as a Heat Sink. LED Fiber Optics!


  • Ships NOW Worldwide
  • PIO Port Access
  • Fiber Optic LED
  • True Heatsink Design
  • Curved Sleek Look
  • Mountable to a desk or wall
  • Customizable!
  • Nearly Indestructible
  • Great Warranty

Manufacturing Website www.Raspberry-Pi-Case.com

Official Store www.MetalPiCase.com

Production Case

Production quality Raspberry Pi case

This is a production quality case designed to meet most RPi owners needs. There is a Kickstarter project trying to make this case available both with and without external screw terminal.

A convertible case - the Raspileon

Raspileon 1.jpg

The Raspileon can be changed from a housing for a server or home computer to a housing with access to the expansion ports. All without using tools. The Raspileon will be available in Germany in the second half of September. More information and a short survey is available on this site (in German): http://plastikdrucker.de/page2/

The PiPod - a case built from a Really Useful Box

PiPod external.jpg

The PiPod case is a DIY project built from a "Really Useful Box" and cable ties. The two most important factors were a) Ability to mount a car rear-view monitor on top, b) protect the SD card by having it enclosed inside the case. More details on the Raspberry PiPod blog

PiPod internal.jpg

The PiSlab - a quick and dirty mounting plate


The PiSlab is made from a slab of 1/4" aluminum and some PCB mounting clips (Mouser P/N 561-LMTP375). More details on this site

SBC Ltd Snap-together Pi case


This is a semi-transparent ABS case that gives access to all the Pi's connectors. It also incorporates light pipes for LEDs.

All in all I'm quite happy with it. What do you think?

Currently available on ebay

>>> Review article and additional high resolution photos for this case.

This case is also available on Amazon, SparkFun, and Adafruit. See the article for additional purchase links for each of these retailers.

Arbofaktur Raspberry Pi Case

A wooden case made from pear, cherry or walnut wood. Available from arbofaktur.de.

Arbofaktur.de raspberry pi gehaeuse kirsche hochkant leer.jpg
Arbofaktur.de raspberry pi gehaeuse kirsche oberseite leer.jpg
Arbofaktur.de raspberry pi gehaeuse kirsche offen voll.jpg

Currently available woods are pear, cherry and walnut. Arbofaktur.de is shipping world-wide (shipping fee: 5€). Payment via bank transfer or PayPal ist possible.

MDF Curved Case for the Raspberry Pi

A case for the Raspberry Pi, using 3mm MDF, laser cut in a pattern that gives it a smooth curved appearance. The result is an object that stands out from the crowd, it hints at the technical Raspberry Pi inside, with a more natural rather than the typical high-tech look. This case started as a personal project/experiment, however it is now made in small batches for sale because many people requested one. It doesn't allow access to the analogue audio and video ports because these are behind a curved section of the case. Available from [1], the drawings are available on Thingiverse.

Mdf curved case rpi.jpg
Mdf curved case rpi2.jpg

Raspberry Pi Case Billet Aluminum Top Quality

This Raspberry Pi case is by far the most durable, functional, and stylish available. Ships within 5 business days no waiting or pre-ordering.

What People Are Saying:

Wolf Paulas Review

From eBay:

"Def the best looking RP case around" vertitis Sep-04-2012

"this is a thing of beauty" gasolene Aug-31-2012

"Perfectly engineered and beautiful case. Great job guys!" the_atilla Aug-29-2012

Raspberry PI Case BL 04.jpg Raspberry PI Case Raspberry Logo 04.jpg Raspberry PI Case BB 04.jpg Raspberry Pi case Skull 03.jpg 4 Different Design Options

Raspberry PI Case w PI 04.jpg Raspberry PI Case Raspberry Logo 06.jpg Access to GPIO

Raspberry PI Case BB led.jpg Raspberry PI Case led label.jpg Fiber Optic Cables above LED's with or without Labels

Raspberry pi case Mounting.jpg Mountable

Available for Sale at:


Manufacturer Barch Designs

Polycase Pi Series Case


The new Pi Series is a stylish and functional case for the Raspberry Pi and is now available from Polycase.


  • Includes 5 light pipes for the LEDs
  • PCB held captive by case with access and labeling for all board components
  • Textured finish resists fingerprints and scratching
  • Ships within 1 business day

Order your case at: Pi Series

Cyntech Raspberry Case

Raspberry Case by Cyntech

The compact, low-cost case is tailored to fit the Raspberry Pi board and provides openings for all the connectors. This includes an exit slot in the side of the case allowing a ribbon cable to be fitted to the board’s 40-pin GPIO header. Another neat feature is the light pipe window for viewing the board’s LED indicators. The case, which is supplied in the distinctive Raspberry colour and printed with the Raspberry Pi logo, provides an attractive solution for protecting the printed circuit board. The cable kit comprises: micro-USB power with PSU, HDMI AV output, Ethernet, USB (type A to B), RCA video (yellow – yellow), 3.5mm audio output. Available from Amazon UK Amazon.co.uk

The same case is also available in blue (pictured) and clear.

BluBerry Case by Cyntech

Tek Berry.40

Tek-berry-rpi-case.jpg Length: 100.6 Width: 73.5 Height: 26.5 Tek berry white paper


Teko enclosure solutions

Order your case at:

Reichelt ordering page Price: 4.95 €

Watterott TEK-BERRY cases Price: 5.00 €

Watterott TEK-BERRY VESA mount Price: 5.00 €

DIN rail mounting case for RPi 2.0

DINpi provides a simple and safe way for mounting and using the Pi on standard DIN rails in professional applications. Due to its complete shielding, it enables using the RPi in harsh or sensitive EMC environments.

There's a modular concept behind the DINpi case. Help us figure out what modules to realise first by using our feature poll below.

Length x Width x Height: 167 mm x 126 mm x 55 mm (height was measured from top of DIN rail)

DINpi Case Development Mule (side view)
DINpi Case Development Mule (top view)

Enlist for updates on availability here:

You can register for updates here.

Request your DINpi feature here:

There is also a product feature poll available here.

DIN rail 4M mounting case with Transparent or Grey panel

Raspberry Pi B+ / Pi 2 / Pi 3 DIN rail mounting enclosure produced specifically for the Raspberry Pi.

DIN rail mounting or Wall mountable

UL94V-0 self extinguishing PPO and PC Material

Dimensions (LxWxH) 90.5x71.3x62mm

Transparent panel or Grey panel depending of your application.

The grey panel can be customized by laser marking

Purchase on Yadom Shop : Here.


DIN rail 4M Compact case for Raspberry Pi B+ / Pi 2 / Pi 3

Compact DIN rail 4M Enclosure specifically for Raspberry Pi B+ / Pi 2 / Pi 3 with wall mounting possibility

DIN rail mounting (EN 60715) or Wall mountable

UL94V-0 self extinguishing PPO and PC Material

Dimensions (LxWxH) 90.5x71.3x32mm

Ideal for professional or home automation applications.

The grey front panel can be customized by laser marking.

Purchase on Yadom Shop : Here.


DIN rail 6M Large mounting case with Transparent or Grey panel

Raspberry Pi B+ / Pi 2 / Pi 3 DIN rail mounting enclosure produced specifically for the Raspberry Pi.

DIN rail mounting or Wall mountable

UL94V-0 self extinguishing PPO and PC Material

Dimensions (LxWxH) 90.5x107x62mm

Transparent panel or Grey panel depending of your application.

The grey panel can be customized by laser marking

Purchase on Yadom Shop : Here.


DIN rail 6M Large Compact case for Raspberry Pi B+ / Pi 2 / Pi 3

Extra large DIN rail 6M Compact Enclosure specifically for Raspberry Pi B+ / Pi 2 / Pi 3 with wall mounting possibility

DIN rail mounting (EN 60715) or Wall mountable

UL94V-0 self extinguishing PPO and PC Material

Dimensions (LxWxH) 90.5x107x32mm

Ideal for professional or home automation applications.

The grey front panel can be customized by laser marking.

Purchase on Yadom Shop : Here.


DIN rail 4M mounting case with OLED display and 4 push buttons

This DIN rail housing for Raspberry Pi has both an OLED display and 4 push buttons keyboard assembled and mounted on a small PCB behind the transparent front panel.

With a simple and qualitative design, the display / keypad card connects through a 100mm flat cable to a daughter card, connecting to the Raspberry Pi's GPIO port.

This expansion card is software compatible with most OLED display libraries (SSD1306 chip).

Display: - OLED Technology - Color: White - Size: 0.96 " - Resolution: 128x64 pixels - Connection: SPI

Keyboard: - 4 micro switches (push buttons) - Connection: GPIO

Dimensions (LxWxH) 90.5x71.3x62mm

Purchase on Yadom Shop : here.


Injection moulding Raspberry Pi case

Buy here!.

  • Industrial quality!
  • Includes screw for fixing version2 boards!
Blue, yellow and red

myraspibox case

Raspberry Pi compatible semi-transparent case/enclosure cut from 3mm thick high quality plexiglass.

All side connectors are made available and engraved/labelled. There is also a cutout for a ribbon cable you may plug into the 26 pin expansion header.

The case has no screws, the pieces snap together making it quick and easy to assemble.


Purchase here:

Europe customers: myraspibox store Price: 6.00€ to 7.00€

USA customers: USA reseller store - Acme Unlimited Price: $7.50

Pi Flavours

Beautifully simple and functional Raspberry Pi case, currently funding on Kickstarter [2]


Adafruit Pi Box

Keep your Raspberry Pi® computer safe and sound in this lovely clear acrylic enclosure. We (Adafruit) designed this case to be beautiful, easy to assemble and perfect for any use (but especially for those who want to tinker!) Adafruit Pi Box

Adafruit-pi-box-1.jpg Adafruit-pi-box-2.jpg Adafruit-pi-box-3.jpg Adafruit-pi-box-4.jpg

>>> Review article and additional high resolution photos for this case.

Pi Pan by AVIES Tech

Pi Pan is an aluminum Raspberry Pi case with a black powder coat finish. The case features a universal base that accepts a variety of security lids and mounting brackets. The security lids protect the SD card, USB connectors and the Ethernet jack.

Pipanhdmi.jpg Pipanrca.jpg Pipansd.jpg Pipanusb.jpg

You can find them for sale on http://www.shopavies.com, Tindie, or eBay.

Proto Armour for Raspberry Pi

MobileApp Systems



Proto Armour for Raspberry Pi protective enclosures are designed specifically for the very popular Raspberry Pi credit-card sized computers. Proto Armour is built for durability in the field and is best suited for applications where high performance and long-term availability are critical. Students, engineers and designers alike, all love the Raspberry Pi for its small size and big list of features and capabilities. While low cost and strong community support top the feature list, an area that challenges many Pi enthusiasts however is experienced first hand while breaking out connections to external hardware and peripherals. Attaching a few cables to the board immediately reveals how lightweight the device is and how vulnerable it is to physical harm. The Raspberry Pi, like most other development boards, is a small fully exposed circuit board with limited non-standard mounting features. Proto Armour for Raspberry Pi offers wrap-around protection and supplements the board's limited non-standard mounting capabilities with a host of structural support and standardized mounting features.


  • Durable Metal Construction
  • Structural Modular Design
  • Camera Board Mount
  • Passive Cooling
  • LED Indicators
  • Security Friendly
  • Affordable


With several thousand Proto Armour for Raspberry Pi enclosures in the field, we've taken steps to ensure compatibility with the latest Raspberry Pi boards. Our proven design is available for the Raspberry Pi 2 Model B, Model B+, and Model B (versions 1 and 2). Not only is Proto Armour compatible with the latest Raspberry Pi 2 Model B, it is also backwards compatible with the original Proto Armour for Raspberry Pi accessories and mounting dimensions.


Physical / Environmental
Enclosure Size 4.97 x 2.97 x 0.97 in (length, width, height)
Weight 8.0 oz
Enclosure Materials Bare (standard) or Anodized (option) 6061 Aluminum, Black Nylon Plastic
Board Mounting 4-40 x 2 screws (Model A and B v2), edge support x 2 (Model B v1)
Threaded Mounting Holes 6-32 x 4 per surface (except bottom)
Security Mounting Holes #6 countersunk 82° x 4 (bottom surface)
Passive Cooling CPU, Ethernet controller, voltage regulator
Port Access Power, GPIO, video, audio, LED, USB, Ethernet, HDMI
What's Included
Enclosure Top and bottom compatible with all Raspberry Pi boards
Raspberry Pi Hardware Pack Screws, washers, pins, bumpers, light pipes, thermal pads, wrenches
Welcome Document Assembly instructions and parts list
Anodized Finishes Black, Red, Clear
Special Anodized Finishes Green, Blue, Yellow, Gold, Orange, Gray, Pink

MobileApp Systems

MathSiMo Pi Case - SD card secured

This Raspberry Pi case leaves an access to USB and ethernet only, It also has an opening for the power cable. SD card is secured inside the case.

Option : shim, label and hdmi output available

Other opening (Composite) available on demand.

Purchase : MathSiMo shop

Sweetbox by Graspinghand

Graspinghand is a collective of young designers founded by Alexander Xanthakis and Bud Aniontinder.

  • Sweetbox is the smallest case of the market.
  • It integrates 3 tailor-made heatsinks made of solid copper.
  • It does have GPIO access with a removable rubber cap.
  • It's compatible with all SD and micro SD adaptors.
  • The case is made of high-performance translucent nylon material.

Currently funding on Kickstarter: http://www.kickstarter.com/projects/677951563/sweetbox-ii-the-perfect-case-for-your-raspberry-pi

Sweetbox hold.jpg
Sweetbox main.jpg
Sweetbox plugged.jpg
Sweetbox open.jpg

More infos on:

Setek Stackable Media Center Pi Case

Setek One Unit.jpg Setek All Cases.jpg

This Raspberry Pi case has an open design to allow for overclocking and allows for easy access to ports. Made with acrylic and Aluminum so that it matches with living room home theater systems.

Option : one, two and three stackable (Or can be expanded to hold more Raspberry Pi's.

Purchase : Single Case - Amazon Dual Case - Amazon Triple Case - Amazon

Banana Robotics Raspberry Pi Box

Banana Robotics is offering snap together cases for your Raspberry Pi. These enclosures are made of laser cut acrylic and feature a swing open top with plenty of ventilation to keep your Pi healthy. Colors include cool blue, banana yellow, raspberry red and crystal clear.

Visit the BananaRobotics.com Raspberry Pi page for a complete selection.

Rackberry Pi: 1U laser-cutted rack-mount for two Pis

  • Including cable-tie-compatible holes for fixing external components like cables, USB-sticks and external drives.
  • Mounting holes: Suitable for distance bolts with 2.5mm thread (M2,5), holes for front- and back-mounting of shorter edges.
  • Dimensions: 48,3 x 4,4 x 13 cm
  • License: CC BY SA 4.0, wetterfrosch (wetter_ätt_netzpolitik_dott-org)
  • Just add glue!

Project page with DXF-files:

Axiris Case

Axiris Case for Raspberry Pi

Laser cut acrylic case for use with Raspberry Pi computer. Slot for camera module cable. 3 mm transparant/translucent/black acrylic panels with screw mounting. Rubber feet at the corners.

For more information visit the product page


  1. The PiCano is not just some collection of sheet material and spacers. A carefully thought-out design is the reason for its unique look.
  2. With a Raspberry Pi your screen can be used as media center or gaming device.
  3. Attach it behind your screen using its standard VESA 100x100 mm mount while still allowing other devices to connect to it.
  4. The holographic effect of the acrylic PCB-carrier adds to the design.
  5. Supports stacks of Raspberry Pi devices
PiCano is a VESA-compliant Raspberry Pi enclose with a slick design
Attached to the standard vesa mount interface of a screen
It also serves as a VESA bracket, allowing to attach even more VESA devices
PCB core fits the Raspberry Pi perfectly
Modular design allows stacking (ideal for Raspberry Pi clusters)

Check out the product page at www.picano.info

Also check out this Assembly video on YouTube.

Kurokesu Raspbery Pi case

Industrial design Raspberry pi enclosure made by Saulius Lukse initially was listed on www.lukse.lt blog, later transferred to www.kurokesu.com e-shop.

Pi Zero W Tic Tac Case

A cheap, simple, and effective DIY Pi Zero W case made using a standard Tic Tac container www.instructables.com/id/Pi-Zero-W-Tic-Tac-Case instructable.