Booting of kernel stops at [ 23.047503] mmc0: error -110 whilst initialising MMC card

Jump to: navigation, search

Booting logs for mmcblk0p1[edit]

s

  • udo picocom --baud 115200 /dev/ttyUSB0
  • [sudo] password:
  • picocom v1.7
  • port is  : /dev/ttyUSB0
  • flowcontrol  : none
  • baudrate is  : 115200
  • parity is  : none
  • databits are  : 8
  • escape is  : C-a
  • local echo is  : no
  • noinit is  : no
  • noreset is  : no
  • nolock is  : no
  • send_cmd is  : sz -vv
  • receive_cmd is : rz -vv
  • imap is  :
  • omap is  :
  • emap is  : crcrlf,delbs,
  • Terminal ready
  • [ 0.000192] NOTICE: BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.16
  • [ 0.005757] NOTICE: BL2: PRR is R-Car M3 Ver1.0
  • [ 0.010339] NOTICE: BL2: Board is Starter Kit Rev1.0
  • [ 0.015366] NOTICE: BL2: Boot device is HyperFlash(80MHz)
  • [ 0.020792] NOTICE: BL2: LCM state is CM
  • [ 0.024832] NOTICE: BL2: AVS setting succeeded. DVFS_SetVID=0x53
  • [ 0.030814] NOTICE: BL2: DDR3200(rev.0.27)NOTICE: [COLD_BOOT]NOTICE: ..0
  • [ 0.054038] NOTICE: BL2: DRAM Split is 2ch
  • [ 0.057923] NOTICE: BL2: QoS is default setting(rev.0.19)
  • [ 0.063421] NOTICE: BL2: Lossy Decomp areas
  • [ 0.067600] NOTICE: Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
  • [ 0.074685] NOTICE: Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
  • [ 0.081597] NOTICE: Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
  • [ 0.088512] NOTICE: BL2: v1.3(release):b330e0e
  • [ 0.093001] NOTICE: BL2: Built : 16:52:57, Feb 13 2018
  • [ 0.098189] NOTICE: BL2: Normal boot
  • [ 0.101830] NOTICE: BL2: dst=0xe631f208 src=0x8180000 len=512(0x200)
  • [ 0.108379] NOTICE: BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
  • [ 0.114838] NOTICE: BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
  • [ 0.122063] NOTICE: BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
  • [ 0.132542] NOTICE: BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)
  • U-Boot 2015.04 (Feb 13 2018 - 17:53:05)
  • CPU: Renesas Electronics R8A7796 rev 1.0
  • Board: M3ULCB
  • I2C: ready
  • DRAM: 1.9 GiB
  • Flash: 64 MiB
  • MMC: sh-sdhi: 0, sh-sdhi: 1
  • MMC init failed
  • Using default environment
  • In: serial
  • Out: serial
  • Err: serial
  • Net: Board Net Initialization Failed
  • No ethernet found.
  • Hit any key to stop autoboot: 0
  • => mmc dev 0
  • switch to partitions #0, OK
  • mmc0 is current device
  • => mmc info
  • Device: sh-sdhi
  • Manufacturer ID: 9f
  • OEM: 5449
  • Name: SD128
  • Tran Speed: 50000000
  • Rd Block Len: 512
  • SD version 3.0
  • High Capacity: Yes
  • Capacity: 116.2 GiB
  • Bus Width: 4-bit
  • Erase Group Size: 512 Bytes
  • => ext2ls mmc 0:1 /boot
  • <DIR> 4096 .
  • <DIR> 4096 ..
  • <SYM> 28 Image
  • 18522624 Image-4.14.35-yocto-standard
  • 67069 Image-r8a7796-m3ulcb.dtb
  • =>setenv bootargs 'rw root=/dev/mmcblk0p1 rootfstype=ext3 rootwait'
  • => ext2load mmc 0:1 0x48080000 /boot/Image
  • 18522624 bytes read in 788 ms (22.4 MiB/s)
  • => ext2load mmc 0:1 0x48000000 /boot/Image-r8a7796-m3ulcb.dtb
  • 67069 bytes read in 17 ms (3.8 MiB/s)
  • => booti 0x48080000 – 0x48000000
  • # Flattened Device Tree blob at 48000000
  • Booting using the fdt blob at 0x48000000
  • Using Device Tree in place at 0000000048000000, end 00000000480135fc
  • Starting kernel ...
  • [ 0.000000] Booting Linux on physical CPU 0x0
  • [ 0.000000] Linux version 4.14.35-yocto-standard (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP PREEMPT Sun Feb 17 20:28:45 CST 2019
  • [ 0.000000] Boot CPU: AArch64 Processor [411fd073]
  • [ 0.000000] Machine model: Renesas M3ULCB board based on r8a7796
  • [ 0.000000] efi: Getting EFI parameters from FDT:
  • [ 0.000000] efi: UEFI not found.
  • [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB
  • [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
  • [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
  • [ 0.000000] OF: reserved mem: initialized node linux,multimedia, compatible id shared-dma-pool
  • [ 0.000000] NUMA: No NUMA configuration found
  • [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000063fffffff]
  • [ 0.000000] NUMA: NODE_DATA [mem 0x63ff96600-0x63ff980ff]
  • [ 0.000000] Zone ranges:
  • [ 0.000000] DMA [mem 0x0000000048000000-0x00000000ffffffff]
  • [ 0.000000] Normal [mem 0x0000000100000000-0x000000063fffffff]
  • [ 0.000000] Movable zone start for each node
  • [ 0.000000] Early memory node ranges
  • [ 0.000000] node 0: [mem 0x0000000048000000-0x0000000053ffffff]
  • [ 0.000000] node 0: [mem 0x0000000057000000-0x000000007fffffff]
  • [ 0.000000] node 0: [mem 0x0000000600000000-0x000000063fffffff]
  • [ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000063fffffff]
  • [ 0.000000] psci: probing for conduit method from DT.
  • [ 0.000000] psci: PSCIv1.0 detected in firmware.
  • [ 0.000000] psci: Using standard PSCI v0.2 function IDs
  • [ 0.000000] psci: Trusted OS resident on physical CPU 0x0
  • [ 0.000000] psci: SMC Calling Convention v1.0
  • [ 0.000000] percpu: Embedded 23 pages/cpu @ffff8005fff07000 s55448 r8192 d30568 u94208
  • [ 0.000000] Detected PIPT I-cache on CPU0
  • [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 471744
  • [ 0.000000] Policy zone: Normal
  • [ 0.000000] Kernel command line: rw root=/dev/mmcblk0p1 rootfstype=ext3 rootwait
  • [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
  • [ 0.000000] software IO TLB [mem 0x4ffff000-0x53fff000] (64MB) mapped at [ffff80000ffff000-ffff800013ffefff]
  • [ 0.000000] Memory: 1126832K/1916928K available (10684K kernel code, 1192K rwdata, 4992K rodata, 1152K init, 412K bss, 118352K reserved, 671744K cma-reserved)
  • [ 0.000000] Virtual kernel memory layout:
  • [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
  • [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB)
  • [ 0.000000] .text : 0xffff000008080000 - 0xffff000008af0000 ( 10688 KB)
  • [ 0.000000] .rodata : 0xffff000008af0000 - 0xffff000008fe0000 ( 5056 KB)
  • [ 0.000000] .init : 0xffff000008fe0000 - 0xffff000009100000 ( 1152 KB)
  • [ 0.000000] .data : 0xffff000009100000 - 0xffff00000922a200 ( 1193 KB)
  • [ 0.000000] .bss : 0xffff00000922a200 - 0xffff0000092914e0 ( 413 KB)
  • [ 0.000000] fixed  : 0xffff7dfffe7f9000 - 0xffff7dfffec00000 ( 4124 KB)
  • [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB)
  • [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum)
  • [ 0.000000] 0xffff7e0000200000 - 0xffff7e0018000000 ( 382 MB actual)
  • [ 0.000000] memory  : 0xffff800008000000 - 0xffff800600000000 ( 24448 MB)
  • [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
  • [ 0.000000] Preemptible hierarchical RCU implementation.
  • [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6.
  • [ 0.000000] Tasks RCU enabled.
  • [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
  • [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  • [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f102f000
  • [ 0.000000] GIC: Using split EOI/Deactivate mode
  • [ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (phys).
  • [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns
  • [ 0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns
  • [ 0.000377] Console: colour dummy device 80x25
  • [ 0.000597] console [tty0] enabled
  • [ 0.000640] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)
  • [ 0.000654] pid_max: default: 32768 minimum: 301
  • [ 0.000698] Security Framework initialized
  • [ 0.001481] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  • [ 0.001877] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  • [ 0.001916] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
  • [ 0.001937] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
  • [ 0.015941] ASID allocator initialised with 32768 entries
  • [ 0.023932] Hierarchical SRCU implementation.
  • [ 0.032449] Detected Renesas R-Car Gen3 r8a7796 ES1.0
  • [ 0.033510] EFI services will not be available.
  • [ 0.039963] smp: Bringing up secondary CPUs ...
  • [ 0.068124] Detected PIPT I-cache on CPU1
  • [ 0.068162] CPU1: Booted secondary processor [411fd073]
  • [ 0.096046] psci: failed to boot CPU2 (-22)
  • [ 0.096064] CPU2: failed to boot: -22
  • [ 0.096069] CPU2: failed in unknown state : 0x0
  • [ 0.124078] psci: failed to boot CPU3 (-22)
  • [ 0.124088] CPU3: failed to boot: -22
  • [ 0.124093] CPU3: failed in unknown state : 0x0
  • [ 0.152107] psci: failed to boot CPU4 (-22)
  • [ 0.152115] CPU4: failed to boot: -22
  • [ 0.152121] CPU4: failed in unknown state : 0x0
  • [ 0.180138] psci: failed to boot CPU5 (-22)
  • [ 0.180147] CPU5: failed to boot: -22
  • [ 0.180151] CPU5: failed in unknown state : 0x0
  • [ 0.180185] smp: Brought up 1 node, 2 CPUs
  • [ 0.180192] SMP: Total of 2 processors activated.
  • [ 0.180201] CPU features: detected feature: 32-bit EL0 Support
  • [ 0.180207] CPU features: detected feature: Kernel page table isolation (KPTI)
  • [ 0.184451] CPU: All CPU(s) started at EL2
  • [ 0.184469] alternatives: patching kernel code
  • [ 0.185048] devtmpfs: initialized
  • [ 0.189459] random: get_random_u32 called from bucket_table_alloc+0x108/0x260 with crng_init=0
  • [ 0.189865] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  • [ 0.189927] futex hash table entries: 2048 (order: 6, 262144 bytes)
  • [ 0.197921] pinctrl core: initialized pinctrl subsystem
  • [ 0.198473] random: fast init done
  • [ 0.199513] DMI not present or invalid.
  • [ 0.199766] NET: Registered protocol family 16
  • [ 0.201419] cpuidle: using governor menu
  • [ 0.202367] vdso: 2 pages (1 code @ ffff000008af6000, 1 data @ ffff000009105000)
  • [ 0.202391] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  • [ 0.202933] DMA: preallocated 256 KiB pool for atomic allocations
  • [ 0.203175] Serial: AMBA PL011 UART driver
  • [ 0.206296] sh-pfc e6060000.pin-controller: r8a77960_pfc support registered
  • [ 0.233149] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
  • [ 0.236916] ACPI: Interpreter disabled.
  • [ 0.238893] rcar-avs: use avs value: 0
  • [ 0.238998] rcar-avs: /cpus/cpu@0 is running with: /opp_table0
  • [ 0.239008] rcar-avs: /cpus/cpu@1 is running with: /opp_table0
  • [ 0.239028] rcar-avs: /soc/gsx@fd000000 is running with: /gsx_opp_table0
  • [ 0.240310] vgaarb: loaded
  • [ 0.240607] SCSI subsystem initialized
  • [ 0.248797] usbcore: registered new interface driver usbfs
  • [ 0.248838] usbcore: registered new interface driver hub
  • [ 0.248894] usbcore: registered new device driver usb
  • [ 0.249888] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz
  • [ 0.250208] media: Linux media interface: v0.10
  • [ 0.250241] Linux video capture interface: v2.00
  • [ 0.250310] pps_core: LinuxPPS API ver. 1 registered
  • [ 0.250318] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  • [ 0.250333] PTP clock support registered
  • [ 0.250480] EDAC MC: Ver: 3.0.0
  • [ 0.250769] dmi: Firmware registration failed.
  • [ 0.251432] Advanced Linux Sound Architecture Driver Initialized.
  • [ 0.252697] clocksource: Switched to clocksource arch_sys_counter
  • [ 0.252823] VFS: Disk quotas dquot_6.6.0
  • [ 0.252865] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  • [ 0.252979] pnp: PnP ACPI: disabled
  • [ 0.256930] NET: Registered protocol family 2
  • [ 0.257314] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  • [ 0.257391] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
  • [ 0.257534] TCP: Hash tables configured (established 16384 bind 16384)
  • [ 0.257659] UDP hash table entries: 1024 (order: 3, 32768 bytes)
  • [ 0.257685] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
  • [ 0.257810] NET: Registered protocol family 1
  • [ 0.258083] RPC: Registered named UNIX socket transport module.
  • [ 0.258095] RPC: Registered udp transport module.
  • [ 0.258101] RPC: Registered tcp transport module.
  • [ 0.258107] RPC: Registered tcp NFSv4.1 backchannel transport module.
  • [ 0.258684] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available
  • [ 0.258826] hw perfevents: /soc/pmu_a53: failed to probe PMU!
  • [ 0.258836] hw perfevents: /soc/pmu_a53: failed to register PMU devices!
  • [ 0.259058] kvm [1]: 8-bit VMID
  • [ 0.259806] kvm [1]: vgic interrupt IRQ1
  • [ 0.259855] kvm [1]: Hyp mode initialized successfully
  • [ 0.261754] audit: initializing netlink subsys (disabled)
  • [ 0.261905] audit: type=2000 audit(0.259:1): state=initialized audit_enabled=0 res=1
  • [ 0.262166] workingset: timestamp_bits=44 max_order=19 bucket_order=0
  • [ 0.265470] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  • [ 0.269930] NFS: Registering the id_resolver key type
  • [ 0.269955] Key type id_resolver registered
  • [ 0.269962] Key type id_legacy registered
  • [ 0.269972] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  • [ 0.270100] 9p: Installing v9fs 9p2000 file system support
  • [ 0.271518] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
  • [ 0.271536] io scheduler noop registered
  • [ 0.271642] io scheduler cfq registered (default)
  • [ 0.271650] io scheduler mq-deadline registered
  • [ 0.271657] io scheduler kyber registered
  • [ 0.276897] gpio_rcar e6050000.gpio: driving 16 GPIOs
  • [ 0.277365] gpio_rcar e6051000.gpio: driving 29 GPIOs
  • [ 0.277657] gpio_rcar e6052000.gpio: driving 15 GPIOs
  • [ 0.277858] gpio_rcar e6053000.gpio: driving 16 GPIOs
  • [ 0.278049] gpio_rcar e6054000.gpio: driving 18 GPIOs
  • [ 0.278224] gpio_rcar e6055000.gpio: driving 26 GPIOs
  • [ 0.278412] gpio_rcar e6055400.gpio: driving 32 GPIOs
  • [ 0.278586] gpio_rcar e6055800.gpio: driving 4 GPIOs
  • [ 0.302502] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  • [ 0.304136] SuperH (H)SCI(F) driver initialized
  • [ 0.304632] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 55, base_baud = 0) is a scif
  • [ 1.285638] console [ttySC0] enabled
  • [ 1.289990] msm_serial: driver initialized
  • [ 1.295005] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
  • [ 1.301639] [drm] No driver support for vblank timestamp query.
  • [ 1.308123] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
  • [ 1.317984] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver
  • [ 1.331090] loop: module loaded
  • [ 1.337698] libphy: Fixed MDIO Bus: probed
  • [ 1.342126] tun: Universal TUN/TAP device driver, 1.6
  • [ 1.348214] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
  • [ 1.354116] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
  • [ 1.360078] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
  • [ 1.367071] igb: Copyright (c) 2007-2014 Intel Corporation.
  • [ 1.372677] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
  • [ 1.380523] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
  • [ 1.386788] sky2: driver version 1.30
  • [ 1.391263] ravb e6800000.ethernet: no valid MAC address supplied, using a random one
  • [ 1.399176] libphy: ravb_mii: probed
  • [ 1.403772] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:e9:5b:f1:f9:c2, IRQ 52.
  • [ 1.413081] VFIO - User Level meta-driver version: 0.3
  • [ 1.419338] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  • [ 1.425969] ehci-pci: EHCI PCI platform driver
  • [ 1.430448] ehci-platform: EHCI generic platform driver
  • [ 1.436033] ehci-platform ee0a0100.usb: EHCI Host Controller
  • [ 1.441728] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 1
  • [ 1.449710] ehci-platform ee0a0100.usb: irq 143, io mem 0xee0a0100
  • [ 1.468705] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10
  • [ 1.475270] hub 1-0:1.0: USB hub found
  • [ 1.479045] hub 1-0:1.0: 1 port detected
  • [ 1.483248] ehci-orion: EHCI orion driver
  • [ 1.487438] ehci-exynos: EHCI EXYNOS driver
  • [ 1.491713] ehci-msm: Qualcomm On-Chip EHCI Host Controller
  • [ 1.497356] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  • [ 1.503550] ohci-pci: OHCI PCI platform driver
  • [ 1.508042] ohci-platform: OHCI generic platform driver
  • [ 1.513498] ohci-platform ee0a0000.usb: Generic Platform OHCI controller
  • [ 1.520220] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 2
  • [ 1.528175] ohci-platform ee0a0000.usb: irq 143, io mem 0xee0a0000
  • [ 1.623005] hub 2-0:1.0: USB hub found
  • [ 1.626776] hub 2-0:1.0: 1 port detected
  • [ 1.630941] ohci-exynos: OHCI EXYNOS driver
  • [ 1.635657] usbcore: registered new interface driver usb-storage
  • [ 1.644113] i2c /dev entries driver
  • [ 1.655063] cs2000-cp 2-004f: revision - C1
  • [ 1.659323] i2c-rcar e6510000.i2c: probed
  • [ 1.668099] i2c-rcar e66d8000.i2c: probed
  • [ 1.677148] rcar_gen3_thermal e6198000.thermal: is using pseudo fixed FUSE values
  • [ 1.689188] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points
  • [ 1.700597] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points
  • [ 1.711730] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points
  • [ 1.721141] sdhci: Secure Digital Host Controller Interface driver
  • [ 1.727341] sdhci: Copyright(c) Pierre Ossman
  • [ 1.732295] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
  • [ 1.800811] renesas_sdhi_internal_dmac ee140000.sd: mmc0 base at 0xee140000 max clock rate 200 MHz
  • [ 1.809997] Synopsys Designware Multimedia Card Interface Driver
  • [ 1.817651] sdhci-pltfm: SDHCI platform and OF driver helper
  • [ 1.824621] ledtrig-cpu: registered to indicate activity on CPUs
  • [ 1.831559] usbcore: registered new interface driver usbhid
  • [ 1.837152] usbhid: USB HID core driver
  • [ 1.841938] optee: probing for conduit method from DT.
  • [ 1.847355] R-Car Rev.1.0.8
  • [ 1.850172] optee: initialized driver
  • [ 1.862885] rcar_sound ec500000.sound: probed
  • [ 1.867566] NET: Registered protocol family 17
  • [ 1.872076] 9pnet: Installing 9P2000 support
  • [ 1.876396] Key type dns_resolver registered
  • [ 1.881045] registered taskstats version 1
  • [ 1.889036] thermal emergency: set temperature to 110 celsius
  • [ 1.894847] thermal emergency: shutdown target cpus 1
  • [ 1.899900] thermal emergency: freq scaled target cpus 0
  • [ 1.905502] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs
  • [ 1.913554] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
  • [ 1.920189] [drm] No driver support for vblank timestamp query.
  • [ 1.926748] [drm] Cannot find any crtc or sizes
  • [ 1.931717] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0
  • [ 1.939481] [drm] Device feb00000.display probed
  • [ 1.944493] [drm] Cannot find any crtc or sizes
  • [ 1.949623] bd9571mwv 7-0030: Device: BD9571MWV rev. 1
  • [ 1.960024] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
  • [ 2.024895] renesas_sdhi_internal_dmac ee100000.sd: mmc1 base at 0xee100000 max clock rate 200 MHz
  • [ 2.035303] asoc-simple-card sound: ak4613-hifi <-> ec500000.sound mapping ok
  • [ 2.042472] asoc-simple-card sound: ASoC: no DMI vendor name!
  • [ 2.050563] input: keyboard as /devices/platform/keyboard/input/input0
  • [ 2.057349] hctosys: unable to open rtc device (rtc0)
  • [ 2.062820] ALSA device list:
  • [ 2.065832] #0: rsnd-dai.0-ak4613-hifi
  • [ 2.070064] Waiting for root device /dev/mmcblk0p1...
  • [ 6.876702] renesas_sdhi_internal_dmac ee140000.sd: timeout waiting for hardware interrupt (CMD8)
  • [ 6.885689] mmc1: new SDXC card at address 0007
  • [ 6.890449] mmcblk1: mmc1:0007 SD128 116 GiB
  • [ 6.907655] mmc0: error -110 whilst initialising MMC card
  • [ 6.981803] mmcblk1: p1
  • [ 12.252706] renesas_sdhi_internal_dmac ee140000.sd: timeout waiting for hardware interrupt (CMD8)
  • [ 12.283646] mmc0: error -110 whilst initialising MMC card
  • [ 17.628700] renesas_sdhi_internal_dmac ee140000.sd: timeout waiting for hardware interrupt (CMD8)
  • [ 17.659629] mmc0: error -110 whilst initialising MMC card
  • [ 23.004700] renesas_sdhi_internal_dmac ee140000.sd: timeout waiting for hardware interrupt (CMD8)
  • [ 23.035629] mmc0: error -110 whilst initialising MMC card

Booting logs for mmcblk1p1[edit]

  • => setenv bootargs 'rw root=/dev/mmcblk1p1 rootfstype=ext4 rootwait'
  • => ext2load mmc 0:1 0x48080000 /boot/Image
  • 18522624 bytes read in 789 ms (22.4 MiB/s)
  • => ext2load mmc 0:1 0x48000000 /boot/Image-r8a7796-m3ulcb.dtb
  • 67069 bytes read in 17 ms (3.8 MiB/s)
  • => booti 0x48080000 - 0x48000000
  • ## Flattened Device Tree blob at 48000000
  • Booting using the fdt blob at 0x48000000
  • Using Device Tree in place at 0000000048000000, end 00000000480135fc
  • Starting kernel ...
  • [ 0.000000] Booting Linux on physical CPU 0x0
  • [ 0.000000] Linux version 4.14.35-yocto-standard (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP PREEMPT Sun Feb 17 20:28:45 CST 2019
  • [ 0.000000] Boot CPU: AArch64 Processor [411fd073]
  • [ 0.000000] Machine model: Renesas M3ULCB board based on r8a7796
  • [ 0.000000] efi: Getting EFI parameters from FDT:
  • [ 0.000000] efi: UEFI not found.
  • [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB
  • [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
  • [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
  • [ 0.000000] OF: reserved mem: initialized node linux,multimedia, compatible id shared-dma-pool
  • [ 0.000000] NUMA: No NUMA configuration found
  • [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000063fffffff]
  • [ 0.000000] NUMA: NODE_DATA [mem 0x63ff96600-0x63ff980ff]
  • [ 0.000000] Zone ranges:
  • [ 0.000000] DMA [mem 0x0000000048000000-0x00000000ffffffff]
  • [ 0.000000] Normal [mem 0x0000000100000000-0x000000063fffffff]
  • [ 0.000000] Movable zone start for each node
  • [ 0.000000] Early memory node ranges
  • [ 0.000000] node 0: [mem 0x0000000048000000-0x0000000053ffffff]
  • [ 0.000000] node 0: [mem 0x0000000057000000-0x000000007fffffff]
  • [ 0.000000] node 0: [mem 0x0000000600000000-0x000000063fffffff]
  • [ 0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000063fffffff]
  • [ 0.000000] psci: probing for conduit method from DT.
  • [ 0.000000] psci: PSCIv1.0 detected in firmware.
  • [ 0.000000] psci: Using standard PSCI v0.2 function IDs
  • [ 0.000000] psci: Trusted OS resident on physical CPU 0x0
  • [ 0.000000] psci: SMC Calling Convention v1.0
  • [ 0.000000] percpu: Embedded 23 pages/cpu @ffff8005fff07000 s55448 r8192 d30568 u94208
  • [ 0.000000] Detected PIPT I-cache on CPU0
  • [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 471744
  • [ 0.000000] Policy zone: Normal
  • [ 0.000000] Kernel command line: rw root=/dev/mmcblk1p1 rootfstype=ext4 rootwait
  • [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
  • [ 0.000000] software IO TLB [mem 0x4ffff000-0x53fff000] (64MB) mapped at [ffff80000ffff000-ffff800013ffefff]
  • [ 0.000000] Memory: 1126832K/1916928K available (10684K kernel code, 1192K rwdata, 4992K rodata, 1152K init, 412K bss, 118352K reserved, 671744K cma-reserved)
  • [ 0.000000] Virtual kernel memory layout:
  • [ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
  • [ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB)
  • [ 0.000000] .text : 0xffff000008080000 - 0xffff000008af0000 ( 10688 KB)
  • [ 0.000000] .rodata : 0xffff000008af0000 - 0xffff000008fe0000 ( 5056 KB)
  • [ 0.000000] .init : 0xffff000008fe0000 - 0xffff000009100000 ( 1152 KB)
  • [ 0.000000] .data : 0xffff000009100000 - 0xffff00000922a200 ( 1193 KB)
  • [ 0.000000] .bss : 0xffff00000922a200 - 0xffff0000092914e0 ( 413 KB)
  • [ 0.000000] fixed  : 0xffff7dfffe7f9000 - 0xffff7dfffec00000 ( 4124 KB)
  • [ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB)
  • [ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum)
  • [ 0.000000] 0xffff7e0000200000 - 0xffff7e0018000000 ( 382 MB actual)
  • [ 0.000000] memory  : 0xffff800008000000 - 0xffff800600000000 ( 24448 MB)
  • [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
  • [ 0.000000] Preemptible hierarchical RCU implementation.
  • [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=6.
  • [ 0.000000] Tasks RCU enabled.
  • [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=6
  • [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  • [ 0.000000] GIC: Adjusting CPU interface base to 0x00000000f102f000
  • [ 0.000000] GIC: Using split EOI/Deactivate mode
  • [ 0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (phys).
  • [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns
  • [ 0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns
  • [ 0.000380] Console: colour dummy device 80x25
  • [ 0.000600] console [tty0] enabled
  • [ 0.000642] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)
  • [ 0.000656] pid_max: default: 32768 minimum: 301
  • [ 0.000700] Security Framework initialized
  • [ 0.001480] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  • [ 0.001876] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  • [ 0.001914] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
  • [ 0.001935] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
  • [ 0.015945] ASID allocator initialised with 32768 entries
  • [ 0.023935] Hierarchical SRCU implementation.
  • [ 0.032480] Detected Renesas R-Car Gen3 r8a7796 ES1.0
  • [ 0.033532] EFI services will not be available.
  • [ 0.039968] smp: Bringing up secondary CPUs ...
  • [ 0.068125] Detected PIPT I-cache on CPU1
  • [ 0.068164] CPU1: Booted secondary processor [411fd073]
  • [ 0.096047] psci: failed to boot CPU2 (-22)
  • [ 0.096064] CPU2: failed to boot: -22
  • [ 0.096069] CPU2: failed in unknown state : 0x0
  • [ 0.124081] psci: failed to boot CPU3 (-22)
  • [ 0.124090] CPU3: failed to boot: -22
  • [ 0.124096] CPU3: failed in unknown state : 0x0
  • [ 0.152112] psci: failed to boot CPU4 (-22)
  • [ 0.152120] CPU4: failed to boot: -22
  • [ 0.152125] CPU4: failed in unknown state : 0x0
  • [ 0.180144] psci: failed to boot CPU5 (-22)
  • [ 0.180153] CPU5: failed to boot: -22
  • [ 0.180157] CPU5: failed in unknown state : 0x0
  • [ 0.180193] smp: Brought up 1 node, 2 CPUs
  • [ 0.180198] SMP: Total of 2 processors activated.
  • [ 0.180206] CPU features: detected feature: 32-bit EL0 Support
  • [ 0.180213] CPU features: detected feature: Kernel page table isolation (KPTI)
  • [ 0.184451] CPU: All CPU(s) started at EL2
  • [ 0.184466] alternatives: patching kernel code
  • [ 0.185042] devtmpfs: initialized
  • [ 0.189461] random: get_random_u32 called from bucket_table_alloc+0x108/0x260 with crng_init=0
  • [ 0.189864] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  • [ 0.189928] futex hash table entries: 2048 (order: 6, 262144 bytes)
  • [ 0.197962] pinctrl core: initialized pinctrl subsystem
  • [ 0.198509] random: fast init done
  • [ 0.199566] DMI not present or invalid.
  • [ 0.199819] NET: Registered protocol family 16
  • [ 0.201467] cpuidle: using governor menu
  • [ 0.202418] vdso: 2 pages (1 code @ ffff000008af6000, 1 data @ ffff000009105000)
  • [ 0.202440] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  • [ 0.202982] DMA: preallocated 256 KiB pool for atomic allocations
  • [ 0.203219] Serial: AMBA PL011 UART driver
  • [ 0.206350] sh-pfc e6060000.pin-controller: r8a77960_pfc support registered
  • [ 0.229018] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
  • [ 0.229926] ACPI: Interpreter disabled.
  • [ 0.231959] rcar-avs: use avs value: 0
  • [ 0.232054] rcar-avs: /cpus/cpu@0 is running with: /opp_table0
  • [ 0.232065] rcar-avs: /cpus/cpu@1 is running with: /opp_table0
  • [ 0.232085] rcar-avs: /soc/gsx@fd000000 is running with: /gsx_opp_table0
  • [ 0.233468] vgaarb: loaded
  • [ 0.233715] SCSI subsystem initialized
  • [ 0.234260] usbcore: registered new interface driver usbfs
  • [ 0.234299] usbcore: registered new interface driver hub
  • [ 0.234373] usbcore: registered new device driver usb
  • [ 0.235314] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz
  • [ 0.235628] media: Linux media interface: v0.10
  • [ 0.235654] Linux video capture interface: v2.00
  • [ 0.235722] pps_core: LinuxPPS API ver. 1 registered
  • [ 0.235730] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  • [ 0.235747] PTP clock support registered
  • [ 0.235889] EDAC MC: Ver: 3.0.0
  • [ 0.236220] dmi: Firmware registration failed.
  • [ 0.236986] Advanced Linux Sound Architecture Driver Initialized.
  • [ 0.237455] clocksource: Switched to clocksource arch_sys_counter
  • [ 0.237587] VFS: Disk quotas dquot_6.6.0
  • [ 0.237629] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  • [ 0.237738] pnp: PnP ACPI: disabled
  • [ 0.242971] NET: Registered protocol family 2
  • [ 0.243347] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  • [ 0.243437] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
  • [ 0.243576] TCP: Hash tables configured (established 16384 bind 16384)
  • [ 0.243694] UDP hash table entries: 1024 (order: 3, 32768 bytes)
  • [ 0.243725] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
  • [ 0.243844] NET: Registered protocol family 1
  • [ 0.244304] RPC: Registered named UNIX socket transport module.
  • [ 0.244317] RPC: Registered udp transport module.
  • [ 0.244323] RPC: Registered tcp transport module.
  • [ 0.244329] RPC: Registered tcp NFSv4.1 backchannel transport module.
  • [ 0.244920] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available
  • [ 0.245056] hw perfevents: /soc/pmu_a53: failed to probe PMU!
  • [ 0.245064] hw perfevents: /soc/pmu_a53: failed to register PMU devices!
  • [ 0.245293] kvm [1]: 8-bit VMID
  • [ 0.246688] kvm [1]: vgic interrupt IRQ1
  • [ 0.246751] kvm [1]: Hyp mode initialized successfully
  • [ 0.248633] audit: initializing netlink subsys (disabled)
  • [ 0.249003] audit: type=2000 audit(0.243:1): state=initialized audit_enabled=0 res=1
  • [ 0.249057] workingset: timestamp_bits=44 max_order=19 bucket_order=0
  • [ 0.252384] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  • [ 0.257008] NFS: Registering the id_resolver key type
  • [ 0.257039] Key type id_resolver registered
  • [ 0.257046] Key type id_legacy registered
  • [ 0.257057] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  • [ 0.257184] 9p: Installing v9fs 9p2000 file system support
  • [ 0.258547] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
  • [ 0.258564] io scheduler noop registered
  • [ 0.258670] io scheduler cfq registered (default)
  • [ 0.258678] io scheduler mq-deadline registered
  • [ 0.258684] io scheduler kyber registered
  • [ 0.263747] gpio_rcar e6050000.gpio: driving 16 GPIOs
  • [ 0.264010] gpio_rcar e6051000.gpio: driving 29 GPIOs
  • [ 0.264203] gpio_rcar e6052000.gpio: driving 15 GPIOs
  • [ 0.264386] gpio_rcar e6053000.gpio: driving 16 GPIOs
  • [ 0.264558] gpio_rcar e6054000.gpio: driving 18 GPIOs
  • [ 0.264735] gpio_rcar e6055000.gpio: driving 26 GPIOs
  • [ 0.264922] gpio_rcar e6055400.gpio: driving 32 GPIOs
  • [ 0.265085] gpio_rcar e6055800.gpio: driving 4 GPIOs
  • [ 0.285354] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  • [ 0.287462] SuperH (H)SCI(F) driver initialized
  • [ 0.287934] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 55, base_baud = 0) is a scif
  • [ 1.269016] console [ttySC0] enabled
  • [ 1.273320] msm_serial: driver initialized
  • [ 1.278552] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
  • [ 1.285180] [drm] No driver support for vblank timestamp query.
  • [ 1.291672] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
  • [ 1.301546] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver
  • [ 1.314683] loop: module loaded
  • [ 1.321356] libphy: Fixed MDIO Bus: probed
  • [ 1.325706] tun: Universal TUN/TAP device driver, 1.6
  • [ 1.331827] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
  • [ 1.337682] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
  • [ 1.343685] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
  • [ 1.350667] igb: Copyright (c) 2007-2014 Intel Corporation.
  • [ 1.356278] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
  • [ 1.364123] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
  • [ 1.370401] sky2: driver version 1.30
  • [ 1.374880] ravb e6800000.ethernet: no valid MAC address supplied, using a random one
  • [ 1.382797] libphy: ravb_mii: probed
  • [ 1.387398] ravb e6800000.ethernet eth0: Base address at 0xe6800000, a2:a5:8c:e7:ea:39, IRQ 52.
  • [ 1.396676] VFIO - User Level meta-driver version: 0.3
  • [ 1.402953] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  • [ 1.409552] ehci-pci: EHCI PCI platform driver
  • [ 1.414031] ehci-platform: EHCI generic platform driver
  • [ 1.419656] ehci-platform ee0a0100.usb: EHCI Host Controller
  • [ 1.425355] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 1
  • [ 1.433343] ehci-platform ee0a0100.usb: irq 143, io mem 0xee0a0100
  • [ 1.453459] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10
  • [ 1.460019] hub 1-0:1.0: USB hub found
  • [ 1.463792] hub 1-0:1.0: 1 port detected
  • [ 1.467990] ehci-orion: EHCI orion driver
  • [ 1.472184] ehci-exynos: EHCI EXYNOS driver
  • [ 1.476460] ehci-msm: Qualcomm On-Chip EHCI Host Controller
  • [ 1.482106] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  • [ 1.488302] ohci-pci: OHCI PCI platform driver
  • [ 1.492792] ohci-platform: OHCI generic platform driver
  • [ 1.498250] ohci-platform ee0a0000.usb: Generic Platform OHCI controller
  • [ 1.504969] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 2
  • [ 1.512911] ohci-platform ee0a0000.usb: irq 143, io mem 0xee0a0000
  • [ 1.607796] hub 2-0:1.0: USB hub found
  • [ 1.611567] hub 2-0:1.0: 1 port detected
  • [ 1.615720] ohci-exynos: OHCI EXYNOS driver
  • [ 1.620449] usbcore: registered new interface driver usb-storage
  • [ 1.628893] i2c /dev entries driver
  • [ 1.639858] cs2000-cp 2-004f: revision - C1
  • [ 1.644119] i2c-rcar e6510000.i2c: probed
  • [ 1.652883] i2c-rcar e66d8000.i2c: probed
  • [ 1.661887] rcar_gen3_thermal e6198000.thermal: is using pseudo fixed FUSE values
  • [ 1.673891] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points
  • [ 1.685305] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points
  • [ 1.696430] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points
  • [ 1.705917] sdhci: Secure Digital Host Controller Interface driver
  • [ 1.712118] sdhci: Copyright(c) Pierre Ossman
  • [ 1.717067] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
  • [ 1.785564] renesas_sdhi_internal_dmac ee140000.sd: mmc0 base at 0xee140000 max clock rate 200 MHz
  • [ 1.794747] Synopsys Designware Multimedia Card Interface Driver
  • [ 1.802388] sdhci-pltfm: SDHCI platform and OF driver helper
  • [ 1.809354] ledtrig-cpu: registered to indicate activity on CPUs
  • [ 1.816363] usbcore: registered new interface driver usbhid
  • [ 1.821955] usbhid: USB HID core driver
  • [ 1.826755] optee: probing for conduit method from DT.
  • [ 1.832200] R-Car Rev.1.0.8
  • [ 1.835161] optee: initialized driver
  • [ 1.847911] rcar_sound ec500000.sound: probed
  • [ 1.852597] NET: Registered protocol family 17
  • [ 1.857108] 9pnet: Installing 9P2000 support
  • [ 1.861429] Key type dns_resolver registered
  • [ 1.866105] registered taskstats version 1
  • [ 1.874164] thermal emergency: set temperature to 110 celsius
  • [ 1.879972] thermal emergency: shutdown target cpus 1
  • [ 1.885034] thermal emergency: freq scaled target cpus 0
  • [ 1.890642] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs
  • [ 1.898657] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
  • [ 1.905296] [drm] No driver support for vblank timestamp query.
  • [ 1.911865] [drm] Cannot find any crtc or sizes
  • [ 1.916834] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0
  • [ 1.924595] [drm] Device feb00000.display probed
  • [ 1.929614] [drm] Cannot find any crtc or sizes
  • [ 1.934749] bd9571mwv 7-0030: Device: BD9571MWV rev. 1
  • [ 1.945128] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
  • [ 2.009660] renesas_sdhi_internal_dmac ee100000.sd: mmc1 base at 0xee100000 max clock rate 200 MHz
  • [ 2.020021] asoc-simple-card sound: ak4613-hifi <-> ec500000.sound mapping ok
  • [ 2.027189] asoc-simple-card sound: ASoC: no DMI vendor name!
  • [ 2.035375] input: keyboard as /devices/platform/keyboard/input/input0
  • [ 2.042210] hctosys: unable to open rtc device (rtc0)
  • [ 2.047686] ALSA device list:
  • [ 2.050666] #0: rsnd-dai.0-ak4613-hifi
  • [ 2.054889] Waiting for root device /dev/mmcblk1p1...
  • [ 6.881468] renesas_sdhi_internal_dmac ee140000.sd: timeout waiting for hardware interrupt (CMD8)
  • [ 6.890455] mmc1: new SDXC card at address 0007
  • [ 6.895216] mmcblk1: mmc1:0007 SD128 116 GiB
  • [ 6.912424] mmc0: error -110 whilst initialising MMC card
  • [ 6.986573] mmcblk1: p1
  • [ 12.257461] renesas_sdhi_internal_dmac ee100000.sd: timeout waiting for hardware interrupt (CMD18)
  • [ 12.257464] renesas_sdhi_internal_dmac ee140000.sd: timeout waiting for hardware interrupt (CMD8)
  • [ 12.279527] mmc0: error -110 whilst initialising MMC card
  • [ 12.297994] mmcblk1: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0x0
  • [ 17.633459] renesas_sdhi_internal_dmac ee100000.sd: timeout waiting for hardware interrupt (CMD18)
  • [ 17.633461] renesas_sdhi_internal_dmac ee140000.sd: timeout waiting for hardware interrupt (CMD8)
  • [ 17.655521] mmc0: error -110 whilst initialising MMC card
  • [ 17.673984] mmcblk1: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0x0
  • [ 17.683557] mmcblk1: retrying using single block read
  • [ 17.693686] mmcblk1: error -84 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0x0
  • [ 17.703172] print_req_error: I/O error, dev mmcblk1, sector 2048
  • [ 17.714257] mmcblk1: error -84 transferring data, sector 2049, nr 7, cmd response 0x900, card status 0x0
  • [ 17.723740] print_req_error: I/O error, dev mmcblk1, sector 2049
  • [ 17.734824] mmcblk1: error -84 transferring data, sector 2050, nr 6, cmd response 0x900, card status 0x0
  • [ 17.744307] print_req_error: I/O error, dev mmcblk1, sector 2050
  • [ 17.755388] mmcblk1: error -84 transferring data, sector 2051, nr 5, cmd response 0x900, card status 0x0
  • [ 17.764872] print_req_error: I/O error, dev mmcblk1, sector 2051
  • [ 17.775952] mmcblk1: error -84 transferring data, sector 2052, nr 4, cmd response 0x900, card status 0x0
  • [ 17.785435] print_req_error: I/O error, dev mmcblk1, sector 2052
  • [ 17.796517] mmcblk1: error -84 transferring data, sector 2053, nr 3, cmd response 0x900, card status 0x0
  • [ 17.806000] print_req_error: I/O error, dev mmcblk1, sector 2053
  • [ 17.817085] mmcblk1: error -84 transferring data, sector 2054, nr 2, cmd response 0x900, card status 0x0
  • [ 17.826569] print_req_error: I/O error, dev mmcblk1, sector 2054
  • [ 17.837653] mmcblk1: error -84 transferring data, sector 2055, nr 1, cmd response 0x900, card status 0x0
  • [ 17.847136] print_req_error: I/O error, dev mmcblk1, sector 2055
  • [ 17.853152] EXT4-fs (mmcblk1p1): Can't read superblock on 2nd try
  • [ 17.864473] mmcblk1: error -84 transferring data, sector 2050, nr 2, cmd response 0x900, card status 0x0
  • [ 17.873961] print_req_error: I/O error, dev mmcblk1, sector 2050
  • [ 17.885047] mmcblk1: error -84 transferring data, sector 2051, nr 1, cmd response 0x900, card status 0x0
  • [ 17.894532] print_req_error: I/O error, dev mmcblk1, sector 2051
  • [ 17.900547] EXT4-fs (mmcblk1p1): unable to read superblock
  • [ 17.906059] List of all partitions:
  • [ 17.909563] b300 121798656 mmcblk1
  • [ 17.909565] driver: mmcblk
  • [ 17.916365] b301 121797631 mmcblk1p1 00000000-01
  • [ 17.916367]
  • [ 17.923166] No filesystem could mount root, tried:
  • [ 17.923168] ext4
  • [ 17.928055]
  • [ 17.931469] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1)
  • [ 17.939906] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.14.35-yocto-standard #1
  • [ 17.947212] Hardware name: Renesas M3ULCB board based on r8a7796 (DT)
  • [ 17.953648] Call trace:
  • [ 17.956101] [<ffff000008089a50>] dump_backtrace+0x0/0x3c8
  • [ 17.961497] [<ffff000008089e2c>] show_stack+0x14/0x20
  • [ 17.966550] [<ffff000008ac8640>] dump_stack+0x9c/0xbc
  • [ 17.971600] [<ffff0000080ce700>] panic+0x11c/0x28c
  • [ 17.976391] [<ffff000008fe11dc>] mount_block_root+0x214/0x264
  • [ 17.982132] [<ffff000008fe1348>] mount_root+0x11c/0x134
  • [ 17.987352] [<ffff000008fe1498>] prepare_namespace+0x138/0x180
  • [ 17.993181] [<ffff000008fe0d8c>] kernel_init_freeable+0x208/0x22c
  • [ 17.999271] [<ffff000008adaf38>] kernel_init+0x10/0x100
  • [ 18.004492] [<ffff000008084c98>] ret_from_fork+0x10/0x18
  • [ 18.009805] SMP: stopping secondary CPUs
  • [ 18.013726] Kernel Offset: disabled
  • [ 18.017210] CPU features: 0x1802000
  • [ 18.020693] Memory Limit: none
  • [ 18.023748] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,1)
  • [ 23.009455] renesas_sdhi_internal_dmac ee140000.sd: timeout waiting for hardware interrupt (CMD8)
  • [ 23.047503] mmc0: error -110 whilst initialising MMC card

Pozos (talk)

‎22:04, 21 February 2019
Retrieved from "https://elinux.org/Thread:Talk:R-Car/Boards/M3SK/Booting_of_kernel_stops_at_23.047503_mmc0:_error_-110_whilst_initialising_MMC_card_(2)#Booting_of_kernel_stops_at_.5B___23.047503.5D_mmc0:_error_-110_whilst_initialising_MMC_card_3796"