AGL 6.0.0 booting on R-Car H3 not completed

Jump to: navigation, search

Hello.
I built AGL 6.0.0 for the R-Car Starter Kit Premier/H3 according to the AGL guide, and tried booting AGL on the R-Car H3. [See "Steps to reproduce"]

But I can not see completing of AGL boot on R-Car H3.
The kernel does not proceed from message of "Waiting for root device /dev/mmcblk1p1...". [See attached "Booting log"]

Please tell me how to solve it.
In case of AGL 6.0.0 booting on M3, I can see completing of AGL boot[the shell is launched and home-screen is shown at hdmi-display].

Steps to reproduce:

1) Download all layers for the for Flounder 6.0.0
 I have performed according to below page:
 https://wiki.automotivelinux.org/agl-distro/release-notes#funky_flounder
 
 $ repo init -b flounder -m flounder_6.0.0.xml -u https://gerrit.automotivelinux.org/gerrit/AGL/AGL-repo
 $ repo sync
2) Building and Booting the AGL for R-Car Starter Kit Premier/H3
 I have performed for machine h3ulcb according to below page:
 http://docs.automotivelinux.org/docs/getting_started/en/dev/reference/machines/R-Car-Starter-Kit-gen3.html
 
 Note) I set "/boot/r8a7795-es1-h3ulcb.dtb" is instead of "/boot/Image-r8a7795-es1-h3ulcb.dtb" becaseu I cannot find "Image-r8a7795-es1-h3ulcb.dtb" on "/boot/".


Booting log:

[    0.000295] NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.16
[    0.005858] NOTICE:  BL2: PRR is R-Car H3 Ver1.1
[    0.010440] NOTICE:  BL2: Board is Starter Kit Rev1.0
[    0.015468] NOTICE:  BL2: Boot device is HyperFlash(80MHz)
[    0.020893] NOTICE:  BL2: LCM state is CM
[    0.024936] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x53
[    0.030919] NOTICE:  BL2: DDR2800(rev.0.27)NOTICE:  [COLD_BOOT]NOTICE:  ..0
[    0.065554] NOTICE:  BL2: DRAM Split is 4ch
[    0.069438] NOTICE:  BL2: QoS is default setting(rev.0.37)
[    0.074939] NOTICE:  BL2: Lossy Decomp areas
[    0.079114] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.086199] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.093111] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.100027] NOTICE:  BL2: v1.3(release):b330e0e
[    0.104516] NOTICE:  BL2: Built : 01:25:08, Jan 24 2018
[    0.109703] NOTICE:  BL2: Normal boot
[    0.113345] NOTICE:  BL2: dst=0xe6320208 src=0x8180000 len=512(0x200)
[    0.119894] NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
[    0.126352] NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
[    0.133577] NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
[    0.144057] NOTICE:  BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)

U-Boot 2015.04 (Jan 24 2018 - 10:25:14)

CPU: Renesas Electronics R8A7795 rev 1.1
Board: H3ULCB
I2C:   ready
DRAM:  3.9 GiB
Flash: 64 MiB
MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   Board Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
19347968 bytes read in 3092 ms (6 MiB/s)
69134 bytes read in 14 ms (4.7 MiB/s)
## Flattened Device Tree blob at 48000000
   Booting using the fdt blob at 0x48000000
   Using Device Tree in place at 0000000048000000, end 0000000048013e0d

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.0-yocto-standard (oe-user@oe-host) (gcc version 7.3.0 (GCC)) #1 SMP PREEMPT Fri Oct 19 01:57:21 UTC 2018
[    0.000000] Boot CPU: AArch64 Processor [411fd073]
[    0.000000] Machine model: Renesas H3ULCB board based on r8a7795 ES1.x
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000057000000, size 400 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,multimedia, compatible id shared-dma-pool
[    0.000000] NUMA: No NUMA configuration found
[    0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x000000073fffffff]
[    0.000000] NUMA: NODE_DATA [mem 0x73ff99a00-0x73ff9b4ff]
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000048000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000073fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000048000000-0x0000000053ffffff]
[    0.000000]   node   0: [mem 0x0000000057000000-0x000000007fffffff]
[    0.000000]   node   0: [mem 0x0000000500000000-0x000000053fffffff]
[    0.000000]   node   0: [mem 0x0000000600000000-0x000000063fffffff]
[    0.000000]   node   0: [mem 0x0000000700000000-0x000000073fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000048000000-0x000000073fffffff]
[    0.000000] On node 0 totalpages: 1003520
[    0.000000]   DMA zone: 3392 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 217088 pages, LIFO batch:31
[    0.000000]   Normal zone: 12288 pages used for memmap
[    0.000000]   Normal zone: 786432 pages, LIFO batch:31
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS resident on physical CPU 0x0
[    0.000000] random: fast init done
[    0.000000] percpu: Embedded 23 pages/cpu @ffff8006ffede000 s55576 r8192 d30440 u94208
[    0.000000] pcpu-alloc: s55576 r8192 d30440 u94208 alloc=23*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
[    0.000000] Detected PIPT I-cache on CPU0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 987840
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: console=ttySC0,115200 ignore_loglevel vmalloc=384M video=HDMI-A-1:1920x1080-32@60 root=/dev/mmcblk1p1 rw rootfstype=ext4 rootwait rootdelay=2
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] software IO TLB [mem 0x4ffff000-0x53fff000] (64MB) mapped at [ffff80000ffff000-ffff800013ffefff]
[    0.000000] Memory: 3190236K/4014080K available (11196K kernel code, 1230K rwdata, 5276K rodata, 1152K init, 426K bss, 152100K reserved, 671744K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffff000000000000 - 0xffff000008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000   (129022 GB)
[    0.000000]       .text : 0xffff000008080000 - 0xffff000008b70000   ( 11200 KB)
[    0.000000]     .rodata : 0xffff000008b70000 - 0xffff0000090a0000   (  5312 KB)
[    0.000000]       .init : 0xffff0000090a0000 - 0xffff0000091c0000   (  1152 KB)
[    0.000000]       .data : 0xffff0000091c0000 - 0xffff0000092f3a00   (  1231 KB)
[    0.000000]        .bss : 0xffff0000092f3a00 - 0xffff00000935e550   (   427 KB)
[    0.000000]     fixed   : 0xffff7dfffe7fd000 - 0xffff7dfffec00000   (  4108 KB)
[    0.000000]     PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000   (    16 MB)
[    0.000000]     vmemmap : 0xffff7e0000000000 - 0xffff800000000000   (  2048 GB maximum)
[    0.000000]               0xffff7e0000200000 - 0xffff7e001c000000   (   446 MB actual)
[    0.000000]     memory  : 0xffff800008000000 - 0xffff800700000000   ( 28544 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8.
[    0.000000]  Tasks RCU enabled.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Adjusting CPU interface base to 0x00000000f102f000
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] arch_timer: cp15 timer(s) running at 8.33MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1ec02923e, max_idle_ns: 440795202125 ns
[    0.000003] sched_clock: 56 bits at 8MHz, resolution 120ns, wraps every 2199023255496ns
[    0.000357] Console: colour dummy device 80x25
[    0.000399] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.66 BogoMIPS (lpj=33333)
[    0.000407] pid_max: default: 32768 minimum: 301
[    0.000449] Security Framework initialized
[    0.000458] Smack:  Initializing.
[    0.000461] Smack:  IPv6 port labeling enabled.
[    0.002078] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.002886] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.002929] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.002961] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.015963] ASID allocator initialised with 65536 entries
[    0.023952] Hierarchical SRCU implementation.
[    0.032444] Detected Renesas R-Car Gen3 r8a7795 ES1.1
[    0.033480] EFI services will not be available.
[    0.039974] smp: Bringing up secondary CPUs ...
[    0.068129] Detected PIPT I-cache on CPU1
[    0.068172] CPU1: Booted secondary processor [411fd073]
[    0.096136] Detected PIPT I-cache on CPU2
[    0.096154] CPU2: Booted secondary processor [411fd073]
[    0.124164] Detected PIPT I-cache on CPU3
[    0.124182] CPU3: Booted secondary processor [411fd073]
[    0.152106] psci: failed to boot CPU4 (-22)
[    0.152119] CPU4: failed to boot: -22
[    0.152123] CPU4: failed in unknown state : 0x0
[    0.180134] psci: failed to boot CPU5 (-22)
[    0.180138] CPU5: failed to boot: -22
[    0.180141] CPU5: failed in unknown state : 0x0
[    0.208166] psci: failed to boot CPU6 (-22)
[    0.208170] CPU6: failed to boot: -22
[    0.208174] CPU6: failed in unknown state : 0x0
[    0.236196] psci: failed to boot CPU7 (-22)
[    0.236200] CPU7: failed to boot: -22
[    0.236204] CPU7: failed in unknown state : 0x0
[    0.236233] smp: Brought up 1 node, 4 CPUs
[    0.236237] SMP: Total of 4 processors activated.
[    0.236242] CPU features: detected feature: 32-bit EL0 Support
[    0.236354] CPU: All CPU(s) started at EL2
[    0.236890] devtmpfs: initialized
[    0.241742] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.241802] futex hash table entries: 2048 (order: 6, 262144 bytes)
[    0.249675] pinctrl core: initialized pinctrl subsystem
[    0.251047] DMI not present or invalid.
[    0.251298] NET: Registered protocol family 16
[    0.252559] cpuidle: using governor menu
[    0.253416] vdso: 2 pages (1 code @ ffff000008b76000, 1 data @ ffff0000091c5000)
[    0.253429] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.253964] DMA: preallocated 256 KiB pool for atomic allocations
[    0.254199] Serial: AMBA PL011 UART driver
[    0.257329] sh-pfc e6060000.pin-controller: r8a77950_pfc support registered
[    0.277022] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.277982] ACPI: Interpreter disabled.
[    0.279989] rcar-cpufreq: use avs value: 0
[    0.280002] rcar-cpufreq: /cpus/cpu@0 is running with: /opp_table0
[    0.280010] rcar-cpufreq: /cpus/cpu@1 is running with: /opp_table0
[    0.280017] rcar-cpufreq: /cpus/cpu@2 is running with: /opp_table0
[    0.280023] rcar-cpufreq: /cpus/cpu@3 is running with: /opp_table0
[    0.281259] vgaarb: loaded
[    0.281426] SCSI subsystem initialized
[    0.281548] libata version 3.00 loaded.
[    0.281708] usbcore: registered new interface driver usbfs
[    0.281732] usbcore: registered new interface driver hub
[    0.281789] usbcore: registered new device driver usb
[    0.282679] i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 400000 Hz
[    0.283007] media: Linux media interface: v0.10
[    0.283028] Linux video capture interface: v2.00
[    0.283094] pps_core: LinuxPPS API ver. 1 registered
[    0.283098] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.283109] PTP clock support registered
[    0.283336] EDAC MC: Ver: 3.0.0
[    0.283481] dmi: Firmware registration failed.
[    0.284052] Advanced Linux Sound Architecture Driver Initialized.
[    0.284296] NetLabel: Initializing
[    0.284301] NetLabel:  domain hash size = 128
[    0.284304] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.284340] NetLabel:  unlabeled traffic allowed by default
[    0.284628] clocksource: Switched to clocksource arch_sys_counter
[    0.284741] VFS: Disk quotas dquot_6.6.0
[    0.284779] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.284880] pnp: PnP ACPI: disabled
[    0.290375] NET: Registered protocol family 2
[    0.290883] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[    0.291028] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    0.291290] TCP: Hash tables configured (established 32768 bind 32768)
[    0.291416] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.291447] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.291569] NET: Registered protocol family 1
[    0.291814] RPC: Registered named UNIX socket transport module.
[    0.291818] RPC: Registered udp transport module.
[    0.291822] RPC: Registered tcp transport module.
[    0.291825] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.291833] PCI: CLS 0 bytes, default 128
[    0.292536] hw perfevents: enabled with armv8_cortex_a57 PMU driver, 7 counters available
[    0.292683] hw perfevents: /soc/pmu_a53: failed to probe PMU!
[    0.292689] hw perfevents: /soc/pmu_a53: failed to register PMU devices!
[    0.293028] kvm [1]: 8-bit VMID
[    0.293032] kvm [1]: IDMAP page: 48b57000
[    0.293036] kvm [1]: HYP VA range: 800000000000:ffffffffffff
[    0.293770] kvm [1]: vgic-v2@f1040000
[    0.293828] kvm [1]: vgic interrupt IRQ1
[    0.293838] kvm [1]: virtual timer IRQ4
[    0.293892] kvm [1]: Hyp mode initialized successfully
[    0.295643] audit: initializing netlink subsys (disabled)
[    0.295726] audit: type=2000 audit(0.291:1): state=initialized audit_enabled=0 res=1
[    0.295950] workingset: timestamp_bits=44 max_order=20 bucket_order=0
[    0.299072] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.299470] NFS: Registering the id_resolver key type
[    0.299491] Key type id_resolver registered
[    0.299495] Key type id_legacy registered
[    0.299503] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.299631] 9p: Installing v9fs 9p2000 file system support
[    0.301093] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[    0.301101] io scheduler noop registered
[    0.301199] io scheduler cfq registered (default)
[    0.301204] io scheduler mq-deadline registered
[    0.301208] io scheduler kyber registered
[    0.306365] gpio_rcar e6050000.gpio: driving 16 GPIOs
[    0.306594] gpio_rcar e6051000.gpio: driving 28 GPIOs
[    0.306797] gpio_rcar e6052000.gpio: driving 15 GPIOs
[    0.306996] gpio_rcar e6053000.gpio: driving 16 GPIOs
[    0.307180] gpio_rcar e6054000.gpio: driving 18 GPIOs
[    0.307378] gpio_rcar e6055000.gpio: driving 26 GPIOs
[    0.307569] gpio_rcar e6055400.gpio: driving 32 GPIOs
[    0.307765] gpio_rcar e6055800.gpio: driving 4 GPIOs
[    0.326177] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.327725] SuperH (H)SCI(F) driver initialized
[    0.328146] e6e88000.serial: ttySC0 at MMIO 0xe6e88000 (irq = 139, base_baud = 0) is a scif
[    1.424882] console [ttySC0] enabled
[    1.429315] msm_serial: driver initialized
[    1.434422] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.441043] [drm] No driver support for vblank timestamp query.
[    1.447499] rcar-dw-hdmi fead0000.hdmi: Detected HDMI TX controller v2.01a with HDCP (DWC HDMI 2.0 TX PHY)
[    1.457336] rcar-dw-hdmi fead0000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.470891] brd: module loaded
[    1.478402] loop: module loaded
[    1.494743] libphy: Fixed MDIO Bus: probed
[    1.499093] tun: Universal TUN/TAP device driver, 1.6
[    1.505151] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.511170] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.517131] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[    1.524107] igb: Copyright (c) 2007-2014 Intel Corporation.
[    1.529704] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[    1.537536] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[    1.543801] sky2: driver version 1.30
[    1.548255] ravb e6800000.ethernet: no valid MAC address supplied, using a random one
[    1.556152] libphy: ravb_mii: probed
[    1.560769] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 62:ee:99:bb:a7:a4, IRQ 136.
[    1.570101] VFIO - User Level meta-driver version: 0.3
[    1.576303] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.582834] ehci-pci: EHCI PCI platform driver
[    1.587299] ehci-platform: EHCI generic platform driver
[    1.592799] ehci-platform ee0a0100.usb: EHCI Host Controller
[    1.598473] ehci-platform ee0a0100.usb: new USB bus registered, assigned bus number 1
[    1.606445] ehci-platform ee0a0100.usb: irq 146, io mem 0xee0a0100
[    1.628637] ehci-platform ee0a0100.usb: USB 2.0 started, EHCI 1.10
[    1.635158] hub 1-0:1.0: USB hub found
[    1.638920] hub 1-0:1.0: 1 port detected
[    1.643102] ehci-orion: EHCI orion driver
[    1.647241] ehci-exynos: EHCI EXYNOS driver
[    1.651508] ehci-msm: Qualcomm On-Chip EHCI Host Controller
[    1.657151] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.663361] ohci-pci: OHCI PCI platform driver
[    1.667839] ohci-platform: OHCI generic platform driver
[    1.673225] ohci-platform ee0a0000.usb: Generic Platform OHCI controller
[    1.679936] ohci-platform ee0a0000.usb: new USB bus registered, assigned bus number 2
[    1.687847] ohci-platform ee0a0000.usb: irq 146, io mem 0xee0a0000
[    1.782910] hub 2-0:1.0: USB hub found
[    1.786671] hub 2-0:1.0: 1 port detected
[    1.790813] ohci-exynos: OHCI EXYNOS driver
[    1.795547] usbcore: registered new interface driver usb-storage
[    1.801603] usbcore: registered new interface driver usbserial
[    1.807453] usbcore: registered new interface driver usbserial_generic
[    1.813992] usbserial: USB Serial support registered for generic
[    1.822387] i2c /dev entries driver
[    1.833146] cs2000-cp 2-004f: revision - C1
[    1.837376] i2c-rcar e6510000.i2c: probed
[    1.846003] i2c-rcar e66d8000.i2c: probed
[    1.850492] usbcore: registered new interface driver i2c-tiny-usb
[    1.858064] imr fe860000.imr-lx4: IMR device (pdev: -1) registered as /dev/video0
[    1.865757] imr fe870000.imr-lx4: IMR device (pdev: -1) registered as /dev/video1
[    1.873387] imr fe880000.imr-lx4: IMR device (pdev: -1) registered as /dev/video2
[    1.881003] imr fe890000.imr-lx4: IMR device (pdev: -1) registered as /dev/video3
[    1.892080] rcar_gen3_thermal e6198000.thermal: is using pseudo fixed FUSE values
[    1.904493] rcar_gen3_thermal e6198000.thermal: TSC0: Loaded 1 trip points
[    1.915812] rcar_gen3_thermal e6198000.thermal: TSC1: Loaded 1 trip points
[    1.927080] rcar_gen3_thermal e6198000.thermal: TSC2: Loaded 3 trip points
[    1.936207] sdhci: Secure Digital Host Controller Interface driver
[    1.942394] sdhci: Copyright(c) Pierre Ossman
[    1.947274] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
[    1.953425] Synopsys Designware Multimedia Card Interface Driver
[    1.960174] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.967100] ledtrig-cpu: registered to indicate activity on CPUs
[    1.974050] usbcore: registered new interface driver usbhid
[    1.979626] usbhid: USB HID core driver
[    1.984346] optee: probing for conduit method from DT.
[    1.984651] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    1.996781] R-Car Rev.1.0.8
[    1.999890] optee: initialized driver
[    2.004952] usbcore: registered new interface driver snd-usb-audio
[    2.019227] rcar_sound ec500000.sound: probed
[    2.023915] NET: Registered protocol family 17
[    2.028422] 9pnet: Installing 9P2000 support
[    2.032739] Key type dns_resolver registered
[    2.037915] registered taskstats version 1
[    2.047017] thermal emergency: set temperature to 110 celsius
[    2.052832] thermal emergency: shutdown target cpus 1-3
[    2.058056] thermal emergency: freq scaled target cpus 0
[    2.063668] renesas_irqc e61c0000.interrupt-controller: driving 6 irqs
[    2.071503] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.078129] [drm] No driver support for vblank timestamp query.
[    2.147727] hub 1-1:1.0: USB hub found
[    2.151652] hub 1-1:1.0: 4 ports detected
[    2.251577] Console: switching to colour frame buffer device 240x67
[    2.274840] rcar-du feb00000.display: fb0:  frame buffer device
[    2.280995] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0
[    2.288740] [drm] Device feb00000.display probed
[    2.294385] bd9571mwv 7-0030: Device: BD9571MWV rev. 1
[    2.304694] renesas_sdhi_internal_dmac ee100000.sd: Got CD GPIO
[    2.372989] renesas_sdhi_internal_dmac ee100000.sd: mmc0 base at 0xee100000 max clock rate 200 MHz
[    2.383200] asoc-simple-card sound: ak4613-hifi <-> ec500000.sound mapping ok
[    2.390356] asoc-simple-card sound: ASoC: no DMI vendor name!
[    2.398750] input: keyboard as /devices/platform/keyboard/input/input0
[    2.405480] hctosys: unable to open rtc device (rtc0)
[    2.411026] ALSA device list:
[    2.413997]   #0: Loopback 1
[    2.416875]   #1: ak4613
[    2.419744] Waiting 2 sec before mounting root device...
[    2.460636] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
[    2.596971] input: ILITEK Multi-Touch-V5100 as /devices/platform/soc/ee0a0100.usb/usb1/1-1/1-1.1/1-1.1:1.0/0003:222A:011E.0001/input/input1
[    2.609611] hid-multitouch 0003:222A:011E.0001: input: USB HID v1.10 Device [ILITEK Multi-Touch-V5100] on usb-ee0a0100.usb-1.1/input0
[    2.622380] hid-generic 0003:222A:011E.0002: device has no listeners, quitting
[    2.686881] mmc0: new ultra high speed SDR104 SDHC card at address aaaa
[    2.693689] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
[    2.701819]  mmcblk0: p1
[    2.720635] usb 1-1.4: new full-speed USB device number 4 using ehci-platform
[    4.448658] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
[    4.456436] Waiting for root device /dev/mmcblk1p1...
01:35, 22 October 2018

Hi, I report because this issue progress has changed.

I seemed that the U-boot parameters(discribed at http://docs.automotivelinux.org/docs/getting_started/en/dev/reference/machines/R-Car-Starter-Kit-gen3.html) were wrong from the previous Booting log.

[ 2.693689] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
[ 2.701819] mmcblk0: p1
[ 2.720635] usb 1-1.4: new full-speed USB device number 4 using ehci-platform
[ 4.448658] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
[ 4.456436] Waiting for root device /dev/mmcblk1p1...

So, I tried changing the device name from "/dev/mmcblk1p1" to "/dev/mmcblk0p1".
And reboot, the shell is launched completely but home-screen is not shown at hdmi-display yet.
The kernel outputs trace log of WARNING below.

[ 16.128912] -----------[ cut here ]-----------
[ 16.133663] WARNING: CPU: 1 PID: 54 at /mnt/AGL/workspace_agl_ff_6.0.0_rcar/build-h3/tmp/work/h3ulcb-agl-linux/kernel-module-gles/1.0-r0/rogue_km/binary_r8a7795_linux_release/target_aarch64/kbuild/services/server/devices/rgx/rgxfwutils.c:4115 RGXCheckFirmwareCCB+0x210/0x330 [pvrsrvkm]
[ 16.160150] Modules linked in: can_bcm can bnep nfc btwilink st_drv bluetooth ecdh_generic rfkill crc32_ce crct10dif_ce pvrsrvkm(O) vspm_if(O) vsp2(O) vspm(O) uvcs_drv(O) mmngrbuf(O) mmngr(O) hdm_usb(O) hdm_i2c(O) hdm_dim2(O) aim_v4l2(O) aim_sound(O) aim_network(O) aim_cdev(O) mostcore(O) ipv6
[ 16.186172] CPU: 1 PID: 54 Comm: kworker/u16:2 Tainted: G O 4.14.0-yocto-standard #1
[ 16.195037] Hardware name: Renesas H3ULCB board based on r8a7795 ES1.x (DT)
[ 16.202108] Workqueue: pvr_workqueue MISRWrapper [pvrsrvkm]
[ 16.207676] task: ffff8006fae20000 task.stack: ffff000009b40000
[ 16.213698] PC is at RGXCheckFirmwareCCB+0x210/0x330 [pvrsrvkm]
[ 16.219761] LR is at RGXCheckFirmwareCCB+0x210/0x330 [pvrsrvkm]
[ 16.225676] pc : [<ffff000000ce6e28>] lr : [<ffff000000ce6e28>] pstate: 60000145
[ 16.233063] sp : ffff000009b43d60
[ 16.236371] x29: ffff000009b43d60 x28: 0000000000000000
[ 16.241680] x27: 0000000000000000 x26: ffff0000210790a0
[ 16.246988] x25: 0000000070014008 x24: ffff8006f4a705e8
[ 16.252296] x23: ffff000000d45618 x22: ffff8006f4a70000
[ 16.257603] x21: ffff000021079080 x20: 0000000000000020
[ 16.262911] x19: ffff000021079040 x18: 0000000000000010
[ 16.268219] x17: 00000000000012c8 x16: 00000000000012cc
[ 16.273526] x15: 0000000000000001 x14: 0000000000000400
[ 16.278833] x13: 0000000000000400 x12: 0000000000000000
[ 16.284141] x11: 0000000000000005 x10: 0000000000000000
[ 16.289448] x9 : 00000000006cd4b7 x8 : ffff8006ffeea6c0
[ 16.294756] x7 : ffff8006ffeea668 x6 : 00000000000000a7
[ 16.300063] x5 : 0000000000000001 x4 : ffff0000091d2c00
[ 16.305370] x3 : 00000000000f4240 x2 : ffff8006fa5e7088
[ 16.310678] x1 : 0000000000000000 x0 : 0000000000000002
[ 16.315986] Call trace:
[ 16.318427] Exception stack(0xffff000009b43c20 to 0xffff000009b43d60)
[ 16.324862] 3c20: 0000000000000002 0000000000000000 ffff8006fa5e7088 00000000000f4240
[ 16.332684] 3c40: ffff0000091d2c00 0000000000000001 00000000000000a7 ffff8006ffeea668
[ 16.340507] 3c60: ffff8006ffeea6c0 00000000006cd4b7 0000000000000000 0000000000000005
[ 16.348329] 3c80: 0000000000000000 0000000000000400 0000000000000400 0000000000000001
[ 16.356152] 3ca0: 00000000000012cc 00000000000012c8 0000000000000010 ffff000021079040
[ 16.363974] 3cc0: 0000000000000020 ffff000021079080 ffff8006f4a70000 ffff000000d45618
[ 16.371796] 3ce0: ffff8006f4a705e8 0000000070014008 ffff0000210790a0 0000000000000000
[ 16.379619] 3d00: 0000000000000000 ffff000009b43d60 ffff000000ce6e28 ffff000009b43d60
[ 16.387441] 3d20: ffff000000ce6e28 0000000060000145 ffff000009b43d60 ffff000000ce6e28
[ 16.395263] 3d40: ffffffffffffffff 0000000000000020 ffff000009b43d60 ffff000000ce6e28
[ 16.403248] [<ffff000000ce6e28>] RGXCheckFirmwareCCB+0x210/0x330 [pvrsrvkm]
[ 16.410302] [<ffff000000ce893c>] RGX_MISRHandler+0x24/0x38 [pvrsrvkm]
[ 16.416840] [<ffff000000cb5058>] MISRWrapper+0x18/0x20 [pvrsrvkm]
[ 16.422935] [<ffff0000080e06bc>] process_one_work+0x1d4/0x348
[ 16.428675] [<ffff0000080e0878>] worker_thread+0x48/0x470
[ 16.434070] [<ffff0000080e6b64>] kthread+0x12c/0x130
[ 16.439033] [<ffff000008084c10>] ret_from_fork+0x10/0x18
[ 16.444339] --[ end trace da55878e442ea43e ]--

I should do something else?
Perhaps, my knowledge may be missing, but I appreciate if someone let me know advice to solve it.

19:55, 23 October 2018

> [ 0.005858] NOTICE: BL2: PRR is R-Car H3 Ver1.1 According to this log you are using H3 v1.1.

AGL 6.0.0 is based on Yocto v3.7.0.
And Yocto v3.7.0 doesn't support H3 v1.1 SK. Please refer to the following.
https://elinux.org/R-Car/Boards/H3SK#Limitation

Currently, H3 v2.0 and M3 SK are out of stock. I hope that you already have H3 v2.0 SK or M3 SK.

03:23, 24 October 2018

Thank you for letting me know it.

I found that I'm not happy, but I will find someone who already has H3 v2.0 SK or M3 SK.

16:57, 24 October 2018