Can't Modify U-Boot Environment Variables on Updated Firmware

Jump to: navigation, search

I have the same h3ulcb board(RTP0RC77951SKBX010SA00) as you. I updated the loader but it started normally.

[    0.000194] NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.14
[    0.005761] NOTICE:  BL2: PRR is R-Car H3 Ver2.0
[    0.010335] NOTICE:  BL2: Board is unknown Rev0.0
[    0.015006] NOTICE:  BL2: Boot device is HyperFlash(80MHz)
[    0.020445] NOTICE:  BL2: LCM state is CM
[    0.024423] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x52
[    0.030611] NOTICE:  BL2: DDR3200(rev.0.22)NOTICE:  [COLD_BOOT]NOTICE:  ..0
[    0.091235] NOTICE:  BL2: DRAM Split is 4ch
[    0.095121] NOTICE:  BL2: QoS is default setting(rev.0.14)
[    0.100621] NOTICE:  BL2: Lossy Decomp areas
[    0.104798] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.111883] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.118795] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.125709] NOTICE:  BL2: v1.3(release):4eef9a2
[    0.130199] NOTICE:  BL2: Built : 10:20:37, Jul 19 2017
[    0.135386] NOTICE:  BL2: Normal boot
[    0.139028] NOTICE:  BL2: dst=0xe6320190 src=0x8180000 len=512(0x200)
[    0.145574] NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
[    0.152037] NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
[    0.159261] NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
[    0.169741] NOTICE:  BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)


U-Boot 2015.04 (Jul 19 2017 - 10:20:39)

CPU: Renesas Electronics R8A7795 rev 2.0
Board: H3ULCB
I2C:   ready
DRAM:  3.9 GiB
MMC:   sh-sdhi: 0, sh-sdhi: 1
In:    serial
Out:   serial
Err:   serial
Net:   ravb
Hit any key to stop autoboot:  0
=>

However, the following are different.

[    0.100623] NOTICE:  BL2: Lossy Decomp areas
[    0.104798] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
(snip)

It seems that you changed something. At first, could you build according to procedure of elinux?

18:31, 18 July 2017

I'm sorry. The log was completely the same halfway. Have you updated all the files?

- bootparam_sa0.srec
- bl2-h3ulcb.srec
- cert_header_sa6.srec
- bl31-h3ulcb.srec
- tee-h3ulcb.srec
- u-boot-elf.srec
18:50, 18 July 2017

Yes. One thing that wasn't clear to me was where to actually get those files. I've been using the ones that are found in ~/tmp/deploy/images/h3ulcb/ after building yocto. Assuming that's the correct path, I'm going to try rebuilding yocto in case I messed something up in that process.

One possible indication of what the issue is: I looked through the Renesas Device Manual https://www.renesas.com/en-us/doc/products/rcar/R-Car_StarterKit_Gen3_H3_M3_DEV_Rev.053.pdf to find a solution and found that in the section on booting the addresses the board boots from are slightly different from those on the e-linux wiki (looking at page 238 in particular). I'm a machine learning guy by trade and my architecture knowledge is rather scant comparatively so maybe this is nothing/not what I thought it means.

00:10, 19 July 2017

Yes, /tmp/deploy/images/h3ulcb is correct path. Please refer to the No13 of http://elinux.org/R-Car/Boards/Yocto-Gen3#Building_the_BSP_for_Renesas_H3ULCB.2C_M3ULCB.

All updating methods are described below. http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware Could you try again?

If "u-boot" still doesn't start up please attach the log when flashing the firmware.

04:03, 21 July 2017

Rebuilding the whole thing from scratch worked. Something must have gone wrong in the initial build because the .dtb file sizes between the two builds were off by a few hundred bytes.

23:38, 22 July 2017