Firmware update hangs

Jump to: navigation, search

Issue is not yet resolved, please see log below.


H3 SAMPLE LOADER V1.17 2016.11.08

CPU   : AArch64 CA57
DRAM  : LPDDR4 DDR3200
DEVICE: QSPI Flash(S25FS128) at 40MHz DMA
BOOT  : Normal Boot
Backup: DDR Cold Boot
jump to 0xE6330000

H3 MiniMonitor V0.24 2016.11.08

Work Memory SystemRAM (H'E6328000-H'E632FFFF)

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6320000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'0

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) SPI Data Clear(H'FF) Check :H'00000000-0003FFFF Erasing..Erase Completed SAVE SPI-FLASH....... complete!

= Qspi/HyperFlash Save Information ===========[edit]
SpiFlashMemory Stat Address : H'00000000
SpiFlashMemory End Address  : H'00000E67
===============================================[edit]

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'44000000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'1C0000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load) Program over size Error

SpiFlashMemory Stat Address : H'001C0000
SpiFlashMemory End Address  : H'105C05D3

>xls2

Qspi/HyperFlash writing of Gen3 Board Command ========[edit]

Load Program to Spiflash Writes to any of SPI address. Please select,FlashMemory.

  1 : QspiFlash       (U5 : S25FS128S)
  2 : QspiFlash Board (CN2: S25FL512S)
  3 : HyperFlash      (SiP internal)
 Select (1-3)>3
READ ID OK.

Program Top Address & Qspi/HyperFlash Save Address

Please Input Program Top Address =======[edit]
 Please Input : H'e6302000

== Please Input Qspi/HyperFlash Save Address[edit]

 Please Input : H'40000

Work RAM(H'50000000-H'53FFFFFF) Clear.... please send ! ('.' & CR stop load)

02:25, 8 June 2017

> Please Input : H'e6302000 This is wrong address. e6304000 is correct.

I added a table to the wiki. please check again.

http://elinux.org/R-Car/Boards/H3SK#Flashing_firmware

18:57, 18 June 2017