https://elinux.org/api.php?action=feedcontributions&user=Cathylidd&feedformat=atomeLinux.org - User contributions [en]2024-03-29T11:16:04ZUser contributionsMediaWiki 1.31.0https://elinux.org/index.php?title=Mini8118&diff=196976Mini81182012-12-02T04:02:23Z<p>Cathylidd: </p>
<hr />
<div>[[File:Piture4.jpg]]<br />
<br/><br/><br />
'''Features'''<br />
<br/>'''&nbsp;&nbsp;&nbsp;&nbsp;Mechanical Parameters'''<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 125mA @ 12V<br />
'''Processor<br />
*TI AM1808 ARM9 microprocessor<br />
- 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation<br />
<br/>- ARM926EJ-S Core <br />
<br/>- ARM9 Memory Architecture <br />
<br/>- Enhanced Direct-Memory-Access Controller 3 (EDMA3) <br />
<br/>- 128K-Byte On-chip Memory <br />
<br/>- 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces) <br />
<br/>- Two External Memory Interfaces <br />
<br/>- Three Configurable 16550 type UART Modules <br />
<br/>- LCD Controller <br />
<br/>- Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects <br />
<br/>- Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbytes SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO)module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers;<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 9 banks of 16 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''General Description<br />
&nbsp;&nbsp;&nbsp;&nbsp;Measuring only 58mm by 45mm, the Mini8118 processor card is a small and low-cost controller board designed to the core processing component for your next embedded design. It is based on TI’s AM1808 ARM9 application processor which is powered by 375-MHz ARM926EJ-S RISC MPU core. The board has 128bytes mobile DDR2, 128Mbytes NAND Flash and 8Mbytes SPI Flash and uses two 2.0mm space 3*27-pin dip connectors to bring out many hardware peripheral signals and GPIOs from the CPU. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;To help with customers’ prototyping and evaluation, Embest has also designed an expansion board for the single board computer called SBC8118. The SBC8118 has exposed many additional hardware interfaces based on the Mini8118 including Serial ports, LCD/TSP, USB Host, Ethernet, RS485, SATA, Camera, SD card, JTAG, etc. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;The Mini8118 processor card is an industrial-grade module which can work in harsh environment. It is ideal for various applications like medical, industrial, communication, consumer electronics products and etc.<br />
<br/><br/><br />
[[File:Piture5.jpg]]<br />
<br/><br/><br />
[[File:Piture6.jpg]]<br />
<br/>'''Two 2.0mm space 3*27-pin dip connectors<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;Embest Mini8118 processor card is connected to carrier board via two 2.0mm pitch 3*27-pin DIP connectors. <br />
*The connector marked in red below is CON1; table 1-1 described the pin signals of CON1 connector.<br />
[[File:Piture7.jpg]]<br />
<br/><br />
[[File:Cc_1000.jpg]]</div>Cathyliddhttps://elinux.org/index.php?title=Mini8118&diff=196970Mini81182012-12-02T03:57:12Z<p>Cathylidd: </p>
<hr />
<div>[[File:Piture4.jpg]]<br />
<br/><br/><br />
'''Features'''<br />
<br/>'''&nbsp;&nbsp;&nbsp;&nbsp;Mechanical Parameters'''<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 125mA @ 12V<br />
'''Processor<br />
*TI AM1808 ARM9 microprocessor<br />
- 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation<br />
<br/>- ARM926EJ-S Core <br />
<br/>- ARM9 Memory Architecture <br />
<br/>- Enhanced Direct-Memory-Access Controller 3 (EDMA3) <br />
<br/>- 128K-Byte On-chip Memory <br />
<br/>- 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces) <br />
<br/>- Two External Memory Interfaces <br />
<br/>- Three Configurable 16550 type UART Modules <br />
<br/>- LCD Controller <br />
<br/>- Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects <br />
<br/>- Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbytes SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO)module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers;<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 9 banks of 16 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''General Description<br />
&nbsp;&nbsp;&nbsp;&nbsp;Measuring only 58mm by 45mm, the Mini8118 processor card is a small and low-cost controller board designed to the core processing component for your next embedded design. It is based on TI’s AM1808 ARM9 application processor which is powered by 375-MHz ARM926EJ-S RISC MPU core. The board has 128bytes mobile DDR2, 128Mbytes NAND Flash and 8Mbytes SPI Flash and uses two 2.0mm space 3*27-pin dip connectors to bring out many hardware peripheral signals and GPIOs from the CPU. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;To help with customers’ prototyping and evaluation, Embest has also designed an expansion board for the single board computer called SBC8118. The SBC8118 has exposed many additional hardware interfaces based on the Mini8118 including Serial ports, LCD/TSP, USB Host, Ethernet, RS485, SATA, Camera, SD card, JTAG, etc. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;The Mini8118 processor card is an industrial-grade module which can work in harsh environment. It is ideal for various applications like medical, industrial, communication, consumer electronics products and etc.<br />
<br/><br/><br />
[[File:Piture5.jpg]]<br />
<br/><br/><br />
[[File:Piture6.jpg]]<br />
<br/>'''Two 2.0mm space 3*27-pin dip connectors<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;Embest Mini8118 processor card is connected to carrier board via two 2.0mm pitch 3*27-pin DIP connectors. <br />
*The connector marked in red below is CON1; table 1-1 described the pin signals of CON1 connector.<br />
[[File:Piture7.jpg]]<br />
<br/><br />
<table border="1" width="70%"><br />
<tr><br />
<td colspan="3" align="center">'''CON1'''</td><br />
</tr><br />
<tr><br />
<td>'''Pin'''</td><br />
<td>'''Signal'''</td><br />
<td>'''Description'''</td><br />
</tr><br />
<tr><br />
<td>1</td><br />
<td>LCD_D0</td><br />
<td>VP_DOUT[0] / LCD_D[0] / UPP_XD[8] / GP7[8] / PRU1_R31[8]</td><br />
</tr><br />
<tr><br />
<td>2</td><br />
<td>LCD_D1</td><br />
<td>VP_DOUT[1] / LCD_D[1] / UPP_XD[9] / GP7[9] / PRU1_R31[9]</td><br />
</tr><br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=Mini8118&diff=196964Mini81182012-12-02T03:51:38Z<p>Cathylidd: </p>
<hr />
<div>[[File:Piture4.jpg]]<br />
<br/><br/><br />
'''Features'''<br />
<br/>'''&nbsp;&nbsp;&nbsp;&nbsp;Mechanical Parameters'''<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 125mA @ 12V<br />
'''Processor<br />
*TI AM1808 ARM9 microprocessor<br />
- 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation<br />
<br/>- ARM926EJ-S Core <br />
<br/>- ARM9 Memory Architecture <br />
<br/>- Enhanced Direct-Memory-Access Controller 3 (EDMA3) <br />
<br/>- 128K-Byte On-chip Memory <br />
<br/>- 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces) <br />
<br/>- Two External Memory Interfaces <br />
<br/>- Three Configurable 16550 type UART Modules <br />
<br/>- LCD Controller <br />
<br/>- Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects <br />
<br/>- Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbytes SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO)module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers;<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 9 banks of 16 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''General Description<br />
&nbsp;&nbsp;&nbsp;&nbsp;Measuring only 58mm by 45mm, the Mini8118 processor card is a small and low-cost controller board designed to the core processing component for your next embedded design. It is based on TI’s AM1808 ARM9 application processor which is powered by 375-MHz ARM926EJ-S RISC MPU core. The board has 128bytes mobile DDR2, 128Mbytes NAND Flash and 8Mbytes SPI Flash and uses two 2.0mm space 3*27-pin dip connectors to bring out many hardware peripheral signals and GPIOs from the CPU. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;To help with customers’ prototyping and evaluation, Embest has also designed an expansion board for the single board computer called SBC8118. The SBC8118 has exposed many additional hardware interfaces based on the Mini8118 including Serial ports, LCD/TSP, USB Host, Ethernet, RS485, SATA, Camera, SD card, JTAG, etc. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;The Mini8118 processor card is an industrial-grade module which can work in harsh environment. It is ideal for various applications like medical, industrial, communication, consumer electronics products and etc.<br />
<br/><br/><br />
[[File:Piture5.jpg]]<br />
<br/><br/><br />
[[File:Piture6.jpg]]<br />
<br/>'''Two 2.0mm space 3*27-pin dip connectors<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;Embest Mini8118 processor card is connected to carrier board via two 2.0mm pitch 3*27-pin DIP connectors. <br />
*The connector marked in red below is CON1; table 1-1 described the pin signals of CON1 connector.<br />
[[File:Piture7.jpg]]<br />
<br/><br />
<table border="1" width="70%"><br />
<tr><br />
<td colspan="3" align="center">'''CON1'''</td><br />
</tr><br />
<tr><br />
<td>'''Pin'''</td><br />
<td>'''Signal'''</td><br />
<td>'''Description'''</td><br />
</tr><br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=Mini8118&diff=196958Mini81182012-12-02T03:51:07Z<p>Cathylidd: </p>
<hr />
<div>[[File:Piture4.jpg]]<br />
<br/><br/><br />
'''Features'''<br />
<br/>'''&nbsp;&nbsp;&nbsp;&nbsp;Mechanical Parameters'''<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 125mA @ 12V<br />
'''Processor<br />
*TI AM1808 ARM9 microprocessor<br />
- 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation<br />
<br/>- ARM926EJ-S Core <br />
<br/>- ARM9 Memory Architecture <br />
<br/>- Enhanced Direct-Memory-Access Controller 3 (EDMA3) <br />
<br/>- 128K-Byte On-chip Memory <br />
<br/>- 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces) <br />
<br/>- Two External Memory Interfaces <br />
<br/>- Three Configurable 16550 type UART Modules <br />
<br/>- LCD Controller <br />
<br/>- Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects <br />
<br/>- Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbytes SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO)module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers;<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 9 banks of 16 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''General Description<br />
&nbsp;&nbsp;&nbsp;&nbsp;Measuring only 58mm by 45mm, the Mini8118 processor card is a small and low-cost controller board designed to the core processing component for your next embedded design. It is based on TI’s AM1808 ARM9 application processor which is powered by 375-MHz ARM926EJ-S RISC MPU core. The board has 128bytes mobile DDR2, 128Mbytes NAND Flash and 8Mbytes SPI Flash and uses two 2.0mm space 3*27-pin dip connectors to bring out many hardware peripheral signals and GPIOs from the CPU. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;To help with customers’ prototyping and evaluation, Embest has also designed an expansion board for the single board computer called SBC8118. The SBC8118 has exposed many additional hardware interfaces based on the Mini8118 including Serial ports, LCD/TSP, USB Host, Ethernet, RS485, SATA, Camera, SD card, JTAG, etc. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;The Mini8118 processor card is an industrial-grade module which can work in harsh environment. It is ideal for various applications like medical, industrial, communication, consumer electronics products and etc.<br />
<br/><br/><br />
[[File:Piture5.jpg]]<br />
<br/><br/><br />
[[File:Piture6.jpg]]<br />
<br/>'''Two 2.0mm space 3*27-pin dip connectors<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;Embest Mini8118 processor card is connected to carrier board via two 2.0mm pitch 3*27-pin DIP connectors. <br />
*The connector marked in red below is CON1; table 1-1 described the pin signals of CON1 connector.<br />
[[File:Piture7.jpg]]<br />
<br/><br />
<table border="1" width="70%"><br />
<tr><br />
<td colspan="3">CON1</td><br />
</tr><br />
<tr><br />
<td>'''Pin'''</td><br />
<td>'''Signal'''</td><br />
<td>'''Description'''</td><br />
</tr><br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=Mini8118&diff=196952Mini81182012-12-02T03:50:39Z<p>Cathylidd: </p>
<hr />
<div>[[File:Piture4.jpg]]<br />
<br/><br/><br />
'''Features'''<br />
<br/>'''&nbsp;&nbsp;&nbsp;&nbsp;Mechanical Parameters'''<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 125mA @ 12V<br />
'''Processor<br />
*TI AM1808 ARM9 microprocessor<br />
- 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation<br />
<br/>- ARM926EJ-S Core <br />
<br/>- ARM9 Memory Architecture <br />
<br/>- Enhanced Direct-Memory-Access Controller 3 (EDMA3) <br />
<br/>- 128K-Byte On-chip Memory <br />
<br/>- 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces) <br />
<br/>- Two External Memory Interfaces <br />
<br/>- Three Configurable 16550 type UART Modules <br />
<br/>- LCD Controller <br />
<br/>- Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects <br />
<br/>- Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbytes SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO)module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers;<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 9 banks of 16 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''General Description<br />
&nbsp;&nbsp;&nbsp;&nbsp;Measuring only 58mm by 45mm, the Mini8118 processor card is a small and low-cost controller board designed to the core processing component for your next embedded design. It is based on TI’s AM1808 ARM9 application processor which is powered by 375-MHz ARM926EJ-S RISC MPU core. The board has 128bytes mobile DDR2, 128Mbytes NAND Flash and 8Mbytes SPI Flash and uses two 2.0mm space 3*27-pin dip connectors to bring out many hardware peripheral signals and GPIOs from the CPU. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;To help with customers’ prototyping and evaluation, Embest has also designed an expansion board for the single board computer called SBC8118. The SBC8118 has exposed many additional hardware interfaces based on the Mini8118 including Serial ports, LCD/TSP, USB Host, Ethernet, RS485, SATA, Camera, SD card, JTAG, etc. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;The Mini8118 processor card is an industrial-grade module which can work in harsh environment. It is ideal for various applications like medical, industrial, communication, consumer electronics products and etc.<br />
<br/><br/><br />
[[File:Piture5.jpg]]<br />
<br/><br/><br />
[[File:Piture6.jpg]]<br />
<br/>'''Two 2.0mm space 3*27-pin dip connectors<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;Embest Mini8118 processor card is connected to carrier board via two 2.0mm pitch 3*27-pin DIP connectors. <br />
*The connector marked in red below is CON1; table 1-1 described the pin signals of CON1 connector.<br />
[[File:Piture7.jpg]]<br />
<br/><br />
<table bord=1 width="70%"><br />
<tr><br />
<td colspan="3">CON1</td><br />
</tr><br />
<tr><br />
<td>'''Pin'''</td><br />
<td>'''Signal'''</td><br />
<td>'''Description'''</td><br />
</tr><br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=File:Dm-stf4bb.jpg&diff=194930File:Dm-stf4bb.jpg2012-11-21T14:31:06Z<p>Cathylidd: Cathylidd uploaded a new version of &quot;File:Dm-stf4bb.jpg&quot;</p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194624SBC81182012-11-19T07:10:31Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;375MHz TI AM1808 ARM926 Microprocessor<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Onboard 128MByte Mobile DDR2 and 128MByte NAND Flash<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;UARTs, RS485, USB Host, Ethernet, LCD/TSP, SATA, Camera, Buzzer, SD, JTAG...<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Optional WiFi, Camera and 3G Modules<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Ready-to-Run Linux2.6.33 and WinCE 6.0 OS<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]<br />
<br/><br/><br />
[[File:Piture3.jpg]]<br />
<br/><br/><br />
The SBC8118 Single Board Computer is provided with Window CE 6.0.net and Linux 2.6.33 BSP, with steady-going drivers, many of which are all in source code. Please refer to below table.<br />
<table border=1 width="70%"><br />
<tr><br />
<td width="10%"><br />
OS<br />
</td><br />
<td colspan="2" width="40%"><br />
Item<br />
</td><br />
<td width="50%"><br />
Remark<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='6'><br />
Linux<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Kernel<br />
</td><br />
<td><br />
Linux-2.6.33<br />
</td><br />
<td><br />
Supports ROM/CRAM/EXT2/EXT3/FAT/NFS/ JFFS2/UBIFS file systems<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, SATA, key, LED, buzzer, Camera, RS485, PRU SUART<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='7'><br />
WinCE<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan="2"><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, RS485, Camera, PRU SUART, Buzzer, SATA, key, LED<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td colspan="2"><br />
Power Management (Sleep/Wakeup, PWM, ADC)<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
APP<br />
</td><br />
<td><br />
application module<br />
</td><br />
<td><br />
Flash Player plug-in and Flash player<br />
</td><br />
</tr><br />
<br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194618SBC81182012-11-19T07:09:53Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;375MHz TI AM1808 ARM926 Microprocessor<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Onboard 128MByte Mobile DDR2 and 128MByte NAND Flash<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;UARTs, RS485, USB Host, Ethernet, LCD/TSP, SATA, Camera, Buzzer, SD, JTAG...<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Optional WiFi, Camera and 3G Modules<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Ready-to-Run Linux2.6.33 and WinCE 6.0 OS<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]<br />
<br/><br/><br />
[[File:Piture3.jpg]]<br />
<br/><br/><br />
The SBC8118 Single Board Computer is provided with Window CE 6.0.net and Linux 2.6.33 BSP, with steady-going drivers, many of which are all in source code. Please refer to below table.<br />
<table border=1 width="70%"><br />
<tr><br />
<td width="10%"><br />
OS<br />
</td><br />
<td colspan="2" width="40%"><br />
Item<br />
</td><br />
<td width="50%"><br />
Remark<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='6'><br />
Linux<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Kernel<br />
</td><br />
<td><br />
Linux-2.6.33<br />
</td><br />
<td><br />
Supports ROM/CRAM/EXT2/EXT3/FAT/NFS/ JFFS2/UBIFS file systems<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, SATA, key, LED, buzzer, Camera, RS485, PRU SUART<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='7'><br />
WinCE<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan="2"><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, RS485, Camera, PRU SUART, Buzzer, SATA, key, LED<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td colspan="2"><br />
Power Management (Sleep/Wakeup, PWM, ADC)<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
APP<br />
</td><br />
<td><br />
application module<br />
</td><br />
<td><br />
Flash Player plug-in and Flash player<br />
</td><br />
</tr><br />
<br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=Mini8118&diff=194486Mini81182012-11-18T14:20:30Z<p>Cathylidd: </p>
<hr />
<div>[[File:Piture4.jpg]]<br />
<br/><br/><br />
'''Features'''<br />
<br/>'''&nbsp;&nbsp;&nbsp;&nbsp;Mechanical Parameters'''<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 125mA @ 12V<br />
'''Processor<br />
*TI AM1808 ARM9 microprocessor<br />
- 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation<br />
<br/>- ARM926EJ-S Core <br />
<br/>- ARM9 Memory Architecture <br />
<br/>- Enhanced Direct-Memory-Access Controller 3 (EDMA3) <br />
<br/>- 128K-Byte On-chip Memory <br />
<br/>- 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces) <br />
<br/>- Two External Memory Interfaces <br />
<br/>- Three Configurable 16550 type UART Modules <br />
<br/>- LCD Controller <br />
<br/>- Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects <br />
<br/>- Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbytes SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO)module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers;<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 9 banks of 16 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''General Description<br />
&nbsp;&nbsp;&nbsp;&nbsp;Measuring only 58mm by 45mm, the Mini8118 processor card is a small and low-cost controller board designed to the core processing component for your next embedded design. It is based on TI’s AM1808 ARM9 application processor which is powered by 375-MHz ARM926EJ-S RISC MPU core. The board has 128bytes mobile DDR2, 128Mbytes NAND Flash and 8Mbytes SPI Flash and uses two 2.0mm space 3*27-pin dip connectors to bring out many hardware peripheral signals and GPIOs from the CPU. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;To help with customers’ prototyping and evaluation, Embest has also designed an expansion board for the single board computer called SBC8118. The SBC8118 has exposed many additional hardware interfaces based on the Mini8118 including Serial ports, LCD/TSP, USB Host, Ethernet, RS485, SATA, Camera, SD card, JTAG, etc. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;The Mini8118 processor card is an industrial-grade module which can work in harsh environment. It is ideal for various applications like medical, industrial, communication, consumer electronics products and etc.<br />
<br/><br/><br />
[[File:Piture5.jpg]]<br />
<br/><br/><br />
[[File:Piture6.jpg]]<br />
<br/>'''Two 2.0mm space 3*27-pin dip connectors<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;Embest Mini8118 processor card is connected to carrier board via two 2.0mm pitch 3*27-pin DIP connectors. <br />
*The connector marked in red below is CON1; table 1-1 described the pin signals of CON1 connector.<br />
[[File:Piture7.jpg]]</div>Cathyliddhttps://elinux.org/index.php?title=File:Piture7.jpg&diff=194480File:Piture7.jpg2012-11-18T14:18:09Z<p>Cathylidd: </p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=File:Piture6.jpg&diff=194474File:Piture6.jpg2012-11-18T14:16:30Z<p>Cathylidd: </p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=File:Piture5.jpg&diff=194468File:Piture5.jpg2012-11-18T14:16:09Z<p>Cathylidd: </p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=Mini8118&diff=194462Mini81182012-11-18T14:11:25Z<p>Cathylidd: </p>
<hr />
<div>[[File:Piture4.jpg]]<br />
<br/><br/><br />
'''Features'''<br />
<br/>'''&nbsp;&nbsp;&nbsp;&nbsp;Mechanical Parameters'''<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 125mA @ 12V<br />
'''Processor<br />
*TI AM1808 ARM9 microprocessor<br />
- 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation<br />
<br/>- ARM926EJ-S Core <br />
<br/>- ARM9 Memory Architecture <br />
<br/>- Enhanced Direct-Memory-Access Controller 3 (EDMA3) <br />
<br/>- 128K-Byte On-chip Memory <br />
<br/>- 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces) <br />
<br/>- Two External Memory Interfaces <br />
<br/>- Three Configurable 16550 type UART Modules <br />
<br/>- LCD Controller <br />
<br/>- Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects <br />
<br/>- Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbytes SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO)module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers;<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 9 banks of 16 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
'''General Description<br />
&nbsp;&nbsp;&nbsp;&nbsp;Measuring only 58mm by 45mm, the Mini8118 processor card is a small and low-cost controller board designed to the core processing component for your next embedded design. It is based on TI’s AM1808 ARM9 application processor which is powered by 375-MHz ARM926EJ-S RISC MPU core. The board has 128bytes mobile DDR2, 128Mbytes NAND Flash and 8Mbytes SPI Flash and uses two 2.0mm space 3*27-pin dip connectors to bring out many hardware peripheral signals and GPIOs from the CPU. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;To help with customers’ prototyping and evaluation, Embest has also designed an expansion board for the single board computer called SBC8118. The SBC8118 has exposed many additional hardware interfaces based on the Mini8118 including Serial ports, LCD/TSP, USB Host, Ethernet, RS485, SATA, Camera, SD card, JTAG, etc. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;The Mini8118 processor card is an industrial-grade module which can work in harsh environment. It is ideal for various applications like medical, industrial, communication, consumer electronics products and etc.</div>Cathyliddhttps://elinux.org/index.php?title=Mini8118&diff=194456Mini81182012-11-18T14:09:51Z<p>Cathylidd: </p>
<hr />
<div>[[File:Piture4.jpg]]<br />
<br/><br/><br />
'''Features'''<br />
<br/>'''&nbsp;&nbsp;&nbsp;&nbsp;Mechanical Parameters'''<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 125mA @ 12V<br />
'''Processor<br />
*TI AM1808 ARM9 microprocessor<br />
<br/>- 375-MHz ARM926EJ-S RISC MPU, also supports 456MHz operation<br />
<br/>- ARM926EJ-S Core <br />
<br/>- ARM9 Memory Architecture <br />
<br/>- Enhanced Direct-Memory-Access Controller 3 (EDMA3) <br />
<br/>- 128K-Byte On-chip Memory <br />
<br/>- 1.8V or 3.3V LVCMOS IOs (except for USB and DDR2 interfaces) <br />
<br/>- Two External Memory Interfaces <br />
<br/>- Three Configurable 16550 type UART Modules <br />
<br/>- LCD Controller <br />
<br/>- Two Serial Peripheral Interfaces (SPI) Each With Multiple Chip-Selects <br />
<br/>- Two MMC/SD Card Interface with Secure Data I/O (SDIO) Interfaces<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbytes SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
<br/>- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO)module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers;<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 9 banks of 16 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)</div>Cathyliddhttps://elinux.org/index.php?title=Mini8118&diff=194450Mini81182012-11-18T14:07:14Z<p>Cathylidd: Created page with "File:Piture4.jpg <br/><br/> '''Features''' <br/>'''Mechanical Parameters''' <br/>*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design) *Working temperature: -45~85 Celsius *..."</p>
<hr />
<div>[[File:Piture4.jpg]]<br />
<br/><br/><br />
'''Features'''<br />
<br/>'''Mechanical Parameters'''<br />
<br/>*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 125mA @ 12V</div>Cathyliddhttps://elinux.org/index.php?title=File:Piture4.jpg&diff=194444File:Piture4.jpg2012-11-18T14:06:13Z<p>Cathylidd: </p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194438SBC81182012-11-18T14:01:53Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]<br />
<br/><br/><br />
[[File:Piture3.jpg]]<br />
<br/><br/><br />
The SBC8118 Single Board Computer is provided with Window CE 6.0.net and Linux 2.6.33 BSP, with steady-going drivers, many of which are all in source code. Please refer to below table.<br />
<table border=1 width="70%"><br />
<tr><br />
<td width="10%"><br />
OS<br />
</td><br />
<td colspan="2" width="40%"><br />
Item<br />
</td><br />
<td width="50%"><br />
Remark<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='6'><br />
Linux<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Kernel<br />
</td><br />
<td><br />
Linux-2.6.33<br />
</td><br />
<td><br />
Supports ROM/CRAM/EXT2/EXT3/FAT/NFS/ JFFS2/UBIFS file systems<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, SATA, key, LED, buzzer, Camera, RS485, PRU SUART<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='7'><br />
WinCE<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan="2"><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, RS485, Camera, PRU SUART, Buzzer, SATA, key, LED<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td colspan="2"><br />
Power Management (Sleep/Wakeup, PWM, ADC)<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
APP<br />
</td><br />
<td><br />
application module<br />
</td><br />
<td><br />
Flash Player plug-in and Flash player<br />
</td><br />
</tr><br />
<br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194432SBC81182012-11-18T14:01:00Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]<br />
<br/><br/><br />
[[File:Piture3.jpg]]<br />
<br/><br/><br />
The SBC8118 Single Board Computer is provided with Window CE 6.0.net and Linux 2.6.33 BSP, with steady-going drivers, many of which are all in source code. Please refer to below table.<br />
<table border=1 width="70%"><br />
<tr><br />
<td width="10%"><br />
OS<br />
</td><br />
<td colspan="2"><br />
Item<br />
</td><br />
<td width="50%"><br />
Remark<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='6'><br />
Linux<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Kernel<br />
</td><br />
<td><br />
Linux-2.6.33<br />
</td><br />
<td><br />
Supports ROM/CRAM/EXT2/EXT3/FAT/NFS/ JFFS2/UBIFS file systems<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, SATA, key, LED, buzzer, Camera, RS485, PRU SUART<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='7'><br />
Linux<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan="2"><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, RS485, Camera, PRU SUART, Buzzer, SATA, key, LED<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td colspan="2"><br />
Power Management (Sleep/Wakeup, PWM, ADC)<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
APP<br />
</td><br />
<td><br />
application module<br />
</td><br />
<td><br />
Flash Player plug-in and Flash player<br />
</td><br />
</tr><br />
<br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194426SBC81182012-11-18T13:59:27Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]<br />
<br/><br/><br />
[[File:Piture3.jpg]]<br />
<br/><br/><br />
The SBC8118 Single Board Computer is provided with Window CE 6.0.net and Linux 2.6.33 BSP, with steady-going drivers, many of which are all in source code. Please refer to below table.<br />
<table border=1 width="70%"><br />
<tr><br />
<td width="10%"><br />
OS<br />
</td><br />
<td colspan="2"><br />
Item<br />
</td><br />
<td width="50%"><br />
Remark<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='6'><br />
Linux<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Kernel<br />
</td><br />
<td><br />
Linux-2.6.33<br />
</td><br />
<td><br />
Supports ROM/CRAM/EXT2/EXT3/FAT/NFS/ JFFS2/UBIFS file systems<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, SATA, key, LED, buzzer, Camera, RS485, PRU SUART<br />
</td><br />
</tr><br />
<br />
<br />
<br />
<tr><br />
<td><br />
OS<br />
</td><br />
<td colspan="2"><br />
Item<br />
</td><br />
<td><br />
Remark<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='6'><br />
Linux<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan="2"><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, RS485, Camera, PRU SUART, Buzzer, SATA, key, LED<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Power Management (Sleep/Wakeup, PWM, ADC)<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
APP<br />
</td><br />
<td><br />
application module<br />
</td><br />
<td><br />
Flash Player plug-in and Flash player<br />
</td><br />
</tr><br />
<br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194420SBC81182012-11-18T13:56:50Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]<br />
<br/><br/><br />
[[File:Piture3.jpg]]<br />
<br/><br/><br />
The SBC8118 Single Board Computer is provided with Window CE 6.0.net and Linux 2.6.33 BSP, with steady-going drivers, many of which are all in source code. Please refer to below table.<br />
<table border=1 width="70%"><br />
<tr><br />
<td width="10%"><br />
OS<br />
</td><br />
<td colspan="2"><br />
Item<br />
</td><br />
<td width="50%"><br />
Remark<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='6'><br />
Linux<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Kernel<br />
</td><br />
<td><br />
Linux-2.6.33<br />
</td><br />
<td><br />
Supports ROM/CRAM/EXT2/EXT3/FAT/NFS/ JFFS2/UBIFS file systems<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, SATA, key, LED, buzzer, Camera, RS485, PRU SUART<br />
</td><br />
</tr><br />
<br />
<br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194414SBC81182012-11-18T13:55:55Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]<br />
<br/><br/><br />
[[File:Piture3.jpg]]<br />
<br/><br/><br />
The SBC8118 Single Board Computer is provided with Window CE 6.0.net and Linux 2.6.33 BSP, with steady-going drivers, many of which are all in source code. Please refer to below table.<br />
<table border=1 width="70%"><br />
<tr><br />
<td width="10%"><br />
OS<br />
</td><br />
<td colspan="2"><br />
Item<br />
</td><br />
<td width="50%"><br />
Remark<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='6'><br />
Linux<br />
</td><br />
<td rowspan='4' width="25%"><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'width="25%"><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Kernel<br />
</td><br />
<td><br />
Linux-2.6.33<br />
</td><br />
<td><br />
Supports ROM/CRAM/EXT2/EXT3/FAT/NFS/ JFFS2/UBIFS file systems<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, SATA, key, LED, buzzer, Camera, RS485, PRU SUART<br />
</td><br />
</tr><br />
<br />
<br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194408SBC81182012-11-18T13:54:10Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]<br />
<br/><br/><br />
[[File:Piture3.jpg]]<br />
<br/><br/><br />
The SBC8118 Single Board Computer is provided with Window CE 6.0.net and Linux 2.6.33 BSP, with steady-going drivers, many of which are all in source code. Please refer to below table.<br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
OS<br />
</td><br />
<td colspan="2"><br />
Item<br />
</td><br />
Remark<br />
<td><br />
</td><br />
</tr><br />
<br />
<tr><br />
<td rowspan='6'><br />
Linux<br />
</td><br />
<td rowspan='4'><br />
BIOS<br />
</td><br />
Remark<br />
<td rowspan='4'><br />
u-boot<br />
</td><br />
<td><br />
NAND/SPI Flash<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
MMC/SD<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
FAT<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
NET<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Kernel<br />
</td><br />
<td><br />
Linux-2.6.33<br />
</td><br />
<td><br />
Supports ROM/CRAM/EXT2/EXT3/FAT/NFS/ JFFS2/UBIFS file systems<br />
</td><br />
</tr><br />
<br />
<tr><br />
<td><br />
Device Driver<br />
</td><br />
<td colspan="2"><br />
Serial port, RTC, Ethernet, Nand Flash, SPI Flash, LCD, Touch screen,<br />
TF card, USB Host, SATA, key, LED, buzzer, Camera, RS485, PRU SUART<br />
</td><br />
</tr><br />
<br />
<br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194402SBC81182012-11-18T13:45:32Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]<br />
<br/><br/><br />
[[File:Piture3.jpg]]</div>Cathyliddhttps://elinux.org/index.php?title=File:Piture3.jpg&diff=194396File:Piture3.jpg2012-11-18T13:42:15Z<p>Cathylidd: </p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194390SBC81182012-11-18T13:40:57Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface<br />
Input Interface and Other Facilities<br />
*Camera interface (30-pin FPC connector, supports CCD and CMOS cameras)<br />
*One 4-pin SATA power interface (supports 2.5-inch hard disk)<br />
*One 4-bit DIP switch (supports boot mode selection)<br />
*One RESET button<br />
*One User button<br />
*One Power indicator<br />
*One User LED<br />
<br/><br/><br />
[[File:Piture1.jpg]]<br />
<br/><br/><br />
[[File:Piture2.jpg]]</div>Cathyliddhttps://elinux.org/index.php?title=File:Piture2.jpg&diff=194384File:Piture2.jpg2012-11-18T13:40:35Z<p>Cathylidd: </p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=File:Piture1.jpg&diff=194378File:Piture1.jpg2012-11-18T13:39:38Z<p>Cathylidd: </p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194372SBC81182012-11-18T13:35:29Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194366SBC81182012-11-18T13:33:31Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
<br/>'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
<br/>- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
Data Transfer Interface<br />
*Serial port:<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194360SBC81182012-11-18T13:32:41Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
<br/>'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
<br/>'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
<br/>- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
<br/>Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
<br/>Data Transfer Interface<br />
*Serial port:<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194354SBC81182012-11-18T13:31:58Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
<br/>'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
<br/>'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
<br/>- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers(Part of the signals is multiplex with network);<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)<br />
<br/>'''Expansion Board of SBC8118<br />
<br/>Mechanical Parameters<br />
*Dimensions: 160 mm x 100 mm<br />
*Input Voltage: +12V<br />
*Temperature Range: -45 ℃ ~ 80 ℃<br />
*Humidity Range: 20% ~ 90%<br />
<br/>Audio/Video Interfaces<br />
*A TFT LCD interface (50-pin FPC connector, RGB565)<br />
*4 line resistive Touch Screen interface<br />
<br/>Data Transfer Interface<br />
*Serial port:<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 5 line Debug serial port, RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x 3 line serial ports (PRU serial port), RS232 voltage<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;1 x 3 line serial port, TTL voltage (2.0mm pitch 5-pin connector)<br />
*USB Host ports:<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (USB-A Type)<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;2 x USB2.0 (2.0mm pitch 5-pin connector)<br />
*SD card slot<br />
*Ethernet: 10/100Mbps, RJ45 connector<br />
*RS485 interface<br />
*1 x Serial ATA connector, supports both SATA I (1.5 Gbps) and SATA II (3.0 Gbps)<br />
*14-pin JTAG interface</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194348SBC81182012-11-18T13:27:53Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
<br/>'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbit SPI Flash<br />
<br/>'''Expansion Interfaces and Signals Routed to Pins<br />
*Two 2.0mm space 3*27-pin dip connectors<br />
<br/>- TFT LCD Interface (support 16-bpp parallel RGB Interface LCD)<br />
<br/>- Two 8-bit Camera interfaces<br />
<br/>- JTAG Debugger Interface<br />
<br/>- USB 1.1 OHCI (Host) With Integrated PHY (USB1)<br />
<br/>- USB 2.0 OTG Port With Integrated PHY (USB0, Support High-/Full-/Low-Speed)<br />
<br/>- Two SPI interfaces (SPI0 multiplexed with MII); <br />
<br/>- Two inter-integrated circuit (I2C) Bus interfaces (I2C1 multiplexed with UART2)<br />
<br/>- Five UART interfaces; <br />
<br/>- A 10/100 Mb/s Ethernet MAC (EMAC) with a Management Data Input/Output (MDIO) module;<br />
<br/>- A multichannel buffered serial ports (McBSP) with FIFO buffers<br />
<br/>- Four 64-bit general-purpose timers each configurable (one configurable as watchdog); <br />
<br/>- Two 4-line SD/MMC card interfaces; <br />
<br/>- GPIO (Up to 120 pins of general-purpose input/output with programmable interrupt/event generation modes, multiplexed with other peripherals)</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194342SBC81182012-11-18T13:24:50Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
<br/>'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
<br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbitytes SPI Flash</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194336SBC81182012-11-18T13:24:08Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
<br/><br/>'''Processor<br />
*375MHz TI AM1808 ARM926EJ-S Microcontroller, also supports 456MHz operation<br />
<br/><br/>'''Memory<br />
*128MByte Mobile DDR2<br />
*128MByte NAND Flash (on the rear of the board)<br />
*8Mbitytes SPI Flash</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194330SBC81182012-11-18T13:22:01Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]<br />
'''Mechanical Parameters<br />
*Dimensions: 58.0 mm x 45.0 mm (6 layer PCB design)<br />
*Working temperature: -45~85 Celsius<br />
*Humidity Range: 20% ~ 90%<br />
*Power Consumption: 3.3V</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194324SBC81182012-11-18T13:20:47Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is based on AM1808 processor and designed with a tiny processor card Mini8118 mounted directly onto an expansion board. The SBC8118 is characterized as follows:<br />
<br/><br/><br />
[[File:Mini8118.jpg]]</div>Cathyliddhttps://elinux.org/index.php?title=File:Mini8118.jpg&diff=194318File:Mini8118.jpg2012-11-18T13:20:33Z<p>Cathylidd: </p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194312SBC81182012-11-18T13:18:46Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # = Not Provided with Source Code''<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The AM1808 ARM microprocessor contains an ARM RISC CPU for general-purpose processing and systems control. The AM1808 ARM microprocessor consists of the following primary components:<br />
<br/><br />
*ARM926 RISC CPU core and associated memories<br />
*A set of I/O peripherals<br />
*A powerful DMA subsystem and SDRAM EMIF interface</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194306SBC81182012-11-18T13:17:38Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br />
'' * = Provided with Source Code'' <br/><br />
'' # =Not Provided with Source Code''</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194300SBC81182012-11-18T13:17:22Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br />
''*= Provided with Source Code'' <br/><br />
''#=Not Provided with Source Code''</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194294SBC81182012-11-18T13:16:36Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br />
''Italic text''* = Provided with Source Code<br />
<br/><br />
''Italic text''# = Not Provided with Source Code</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194288SBC81182012-11-18T13:16:14Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table><br />
<br/><br />
* = Provided with Source Code<br />
<br/><br />
# = Not Provided with Source Code</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194282SBC81182012-11-18T13:15:36Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CAM8000-A<br />
<td><br />
<td><br />
Analog Camera Module<br />
<td><br />
<td><br />
Camera<br />
<td><br />
<td><br />
Support*<br />
<td><br />
<td><br />
Support*<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
WF8000-U<br />
<td><br />
<td><br />
WiFi Module<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<tr><br />
<td><br />
CDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(CDMA2000 standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
<br />
<br />
<tr><br />
<td><br />
WCDMA8000-U<br />
<td><br />
<td><br />
3G Module <br />
<br/>(WCDMA standard)<br />
<td><br />
<td><br />
USB Host<br />
<td><br />
<td><br />
Not Support<br />
<td><br />
<td><br />
Support#<br />
<td><br />
</tr><br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194276SBC81182012-11-18T13:13:08Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.<br />
<br/><br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td><br />
'''Optional Module<br />
<td><br />
<td><br />
'''Description<br />
<td><br />
<td><br />
'''Interface to Board<br />
<td><br />
<td><br />
'''Linux<br />
<td><br />
<td><br />
'''WinCE<br />
<td><br />
</tr></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194270SBC81182012-11-18T13:11:09Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/><br/>[[File:Dm-stf4bb.jpg]]<br />
<br/><br/>&nbsp;&nbsp;&nbsp;&nbsp;The SBC8118 Single Board Computer is an industrial single board based on TI’s AM1808 ARM9 processor and well-suited for medical, industrial automation and control, communication products and more other applications which are cost-sensitive but require high-speed data transfer and high-capacity storage. It has a flexible design with one tiny core board Mini8118 interfacing to an expansion board through two 2.0mm pitch 3*27-pin dip header connectors.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The core board Mini8118 has integrated the AM1808 processor, 128MB Mobile DDR2, 128MB Nand Flash and 8Mb SPI Flash on board. The SBC8118 expansion board offers features in additional to those provided by the Mini8118 to further expose the features of AM1808. It has a SATA interface as well as an SD card interface to allow large storage capabilities. Up to four serial ports have been brought out by three DB9 connectors. The board also has four USB hosts, Ethernet, LCD/Touch screen, Buzzer, Camera and supports RS485 networking. It has one 14-pin JTAG interface which can be used with XDS100v2 emulator available from Embest. Embest also offers 4.3” and 7” LCD display with touch screen as optional modules for this board.<br />
<br/>&nbsp;&nbsp;&nbsp;&nbsp;The board is a ready-to-run solution which is provided with Linux 2.6.33 and WinCE 6.0 BSP. One CD is delivered along with the goods which includes the software driver source code and relative documents to help customer better understand this board and start their reference design.<br />
Additionally, Embest offers various optional modules for SBC8118 which greatly enhanced the functions of this board.</div>Cathyliddhttps://elinux.org/index.php?title=File:Dm-stf4bb.jpg&diff=194264File:Dm-stf4bb.jpg2012-11-18T13:09:39Z<p>Cathylidd: </p>
<hr />
<div></div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194258SBC81182012-11-18T13:06:23Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack</div>Cathyliddhttps://elinux.org/index.php?title=SBC8118&diff=194252SBC81182012-11-18T13:05:53Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack</div>Cathyliddhttps://elinux.org/index.php?title=DM-STF4BB_Base_Board&diff=189992DM-STF4BB Base Board2012-11-07T14:14:16Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/>[[File:Figure 1-1 DM-STF4BB Base Board.jpg]]<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The DM-STF4BB Base Board from Embest is an expansion board designed especially for STMicroelectronics’ STM32F4DISCOVERY high-performance discovery board which is based on the STM32F407VGT6 ARM Cortex-M4 microcontroller and includes an ST-LINK/V2 embedded debug tool, two ST MEMS, digital accelerometer and digital microphone, one audio DAC with integrated class D speaker driver, LEDs and push buttons and an USB OTG micro-AB connector on board.<br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;The DM-STF4BB Base Board enables the STM32F4DISCOVERY board users to further discover more features of the STM32F4. It has incorporated additional functionalities to the STF32F4DISCOVERY providing Serial ports, USB, Ethernet, CAN, SPI, I2C, GPIO, Camera, TF Card, LCD and Touch Screen interfaces on board. The combination of the DM-STF4BB and the STM32F4DISCOVERY forms an ideal evaluation board Devkit407 for evaluating the STM32F4xx series ARM Cortex-M4 microcontrollers and allows easy prototyping of third party solutions with STM32F4DISCOVERY board or STM32F4xx series microcontrollers.<br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;Embest has ported uC/OS-II to the DevKit407 board and the software also features the GUI support on uC/OS-II and LwIP_v1.3.2 protocal support. Meanwhile, Embest has offered rich software examples for DevKit407 besides those provided by STM32F4DISCOVERY kit. Along with the goods deliveries, Embest provides a CD containing the uC/OS-II BSP and plenty of software examples, board schematic and user manual to help customer better understanding this board and develop their own applications. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;Moreover, Embest offers one 3.5 inch LCD Module DM-LCD35RT (including touch screen) and one 1.3 megapixel Digital Camera Modules for options to implement the video input and output performance on DevKit407<br />
<br/>[[File:Figure 1-2 DevKit407.jpg]]<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;The STMicroelectronics’ STM32F4DISCOVERY board is mounted directly on top of the DM-STF4BB base board to form an evaluation board DevKit407 for STM32F4xx series microcontrollers. The features of the DevKit407 are as following:<br />
<br/>[[File:Figure 1-3.jpg]]<br />
<br/><br/><br />
'''STM32F4DISCOVERY Board (CPU board of DevKit407)<br />
* STM32F407VGT6 microcontroller featuring 32-bit ARM Cortex-M4F core, 1 MB Flash,192KB RAM in an LQFP100 package<br/><br />
* On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone STLINK/V2 (with SWD connector for programming and debugging)<br/><br />
* Board power supply: through USB bus or from an external 5 V supply voltage<br/><br />
* External application power supply: 3 V and 5 V<br/><br />
* LIS302DL, ST MEMS motion sensor, 3-axis digital output accelerometer<br/><br />
* MP45DT02, ST MEMS audio sensor, omni-directional digital microphone<br/><br />
* CS43L22, audio DAC with integrated class D speaker driver<br/><br />
* Eight LEDs:<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;LD1 (red/green) for USB communication<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;LD2 (red) for 3.3 V power on<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;Four user LEDs, LD3 (orange), LD4 (green), LD5 (red) and LD6 (blue)<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;2 USB OTG LEDs LD7 (green) VBus and LD8 (red) over-current<br/><br />
* Two push buttons (user and reset)<br/><br />
* USB OTG FS with micro-AB connector<br/><br />
* Extension header for all LQFP100 I/Os for quick connection to prototyping board and easy probing.<br/><br />
<br/><br />
'''DM-STF4BB Base Board (Expansion Board of DevKit407)<br/><br />
* Working and Storage Temp.: 0~45°C<br/><br />
* Power consumption: +5V@80mA (working without LCD)<br/><br />
* Dimensions: 97.03mm x 83mm<br/><br />
* LCD parallel interface, 16-bit, 8080 mode<br/><br />
* 4-wire resistive touch screen interface<br/><br />
* Camera interface (support 1.3 megapixel Digital Camera, multiplex with UART6)<br/><br />
* One RS232 Serial port (UART6, DB9 connector, multiplex with Camera interface, can be selected by jumpers JP1 and JP2)<br/><br />
* One USB2.0 FS OTG/device/host port (12Mbps, Micro-AB type connector)<br/><br />
* One 10/100Mbps Ethernet Interface<br/><br />
* One 2.54mm pitch 2*20-pin expansion connector brought out below hardware peripherals:<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;5 Serial ports, TTL voltage (multiplex with some functions)<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;4-channel PWM<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;1-channel SPI<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;1-channel I2C<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;1 CAN2.0B interface (need to extend CAN transceivers)<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;6 GPIOs<br/><br/><br />
[[File:Figure 1-5.jpg]]<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The DM-STF4BB base board offers features in addition to those provided by STM32F4DISCOVERY board that has exposed more features of the STMicroelectronics’ STM32F407VGT6 microcontroller through connectors or headers. <br/><br/><br />
[[File:Figure 1-6.jpg]]<br/><br/><br />
'''Features<br/><br />
The DevKit407 software mainly features as below:<br/><br />
* Supports for uC/OS-II_v2.86 operating system<br/><br />
* Supports UCGUI_v3.90a<br/><br />
* Supports FatFs_vR0.08a file system<br/><br />
* Supports LWIP _v1.3.2 protocol stack<br/><br />
'''Development Environment Support<br/><br />
* IAR EWARM<br />
&nbsp;&nbsp;&nbsp;&nbsp;All drivers support IAR EWARM, the EWARM version should be V6.40 or above.<br />
&nbsp;&nbsp;&nbsp;&nbsp;uC/OS-II and uC-GUI Demos do not support IAR EWARM at present.<br/><br />
* Keil MDK-ARM<br />
&nbsp;&nbsp;&nbsp;&nbsp;All drivers and applications support Keil MDK-ARM, the MDK-ARM version should be V4.22a or above.<br/><br />
'''Debug Tools Support<br/><br />
* ULINK2<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;It would be best to use with Keil MDK-ARM.<br/><br />
* JLINK-V8<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;It would be best to use with IAR EWARM. <br/><br />
* ST-LINK/V2<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;It can be used with either Keil MDK-ARM or IAR EWARM. <br/><br/><br />
'''Drivers and Software examples<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;Embest has offered rich software examples for DevKit407 besides those provided by STM32F4DISCOVERY kit such as examples for USB, Ethernet and so on. Meanwhile, Embest has provided some system-level application demos which can help customers get into the second development rapidly to reduce the development time. Please check from below table to know more about the drivers and software examples provided by Embest.<br/><br/><br />
<br />
Table 1-1 Drivers and Application Demos<br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td width="15%">01-USART</td><br />
<td width="25%">USART_Printf</td><br />
<td>Hyper-Terminal Input/Output example</td><br />
</tr><br />
<tr><br />
<td rowspan='2'>02-SDIO</td><br />
<td>uSDCard</td><br />
<td>Read and write, erase of TF card example</td><br />
</tr><br />
<tr><br />
<td>FatFs</td><br />
<td>Port FatFs file system to TF card example</td><br />
</tr><br />
<tr><br />
<td rowspan='2'>03-LCD</td><br />
<td>LCD_35T</td><br />
<td>3.5 inch TFT LCD driver testing example</td><br />
</tr><br />
<tr><br />
<td>LCD_Touch</td><br />
<td>Touch screen testing example</td><br />
</tr><br />
<tr><br />
<td>04-DCMI</td><br />
<td>OV9655_Camera</td><br />
<td>DM-CAM130 module demo, can take photos</td><br />
</tr><br />
<tr><br />
<td colspan='3'>05-ETH_LwIP</td><br />
</tr><br />
<tr><br />
<td rowspan='5'>Standalone</td><br />
<td>httpserver</td><br />
<td>Webserver application demo</td><br />
</tr><br />
<tr><br />
<td>tcp_echo_client</td><br />
<td>Simple echo application demo of tcp customer end</td><br />
</tr><br />
<tr><br />
<td>tcp_echo_server</td><br />
<td>Simple echo application demo of tcp server end</td><br />
</tr><br />
<tr><br />
<td>udp_echo_client</td><br />
<td>Simple echo application demo of udp customer end</td><br />
</tr><br />
<tr><br />
<td>udp_echo_server</td><br />
<td>Simple echo application demo of udp server end</td><br />
</tr><br />
<tr><br />
<td rowspan='3'>FreeRTOS</td><br />
<td>httpserver_netconn</td><br />
<td>Webserver application demo based on netconn</td><br />
</tr><br />
<tr><br />
<td>Httpserver_socket</td><br />
<td>Webserver application demo based on socket</td><br />
</tr><br />
<tr><br />
<td>udptcp_echo_server_netconn</td><br />
<td>Echo application demo based on TCP/UDP server of netconn</td><br />
</tr><br />
<tr><br />
<td colspan='3'>06-USB</td><br />
</tr><br />
<tr><br />
<td rowspan='3'>USB_Device_Examples</td><br />
<td>DFU</td><br />
<td>Use DevKit407 as DFU equipment, user can use it for system firmware upgrading</td><br />
</tr><br />
<tr><br />
<td>MSC</td><br />
<td>Use DevKit407 as MSC (Mass Storage Device) to implement the data exchange between Host and evaluation board.</td><br />
</tr><br />
<tr><br />
<td>VCP</td><br />
<td>Use DevKit407 as VCP (Virtual COM Port) and user can regard the evaluation board as USB-to-UART converter module</td><br />
</tr><br />
<tr><br />
<td rowspan='2'>USB_Host_Examples</td><br />
<td>HID</td><br />
<td>Use DevKit407 as HID (Human Interaction Device) Host, it can recognize USB mouse and USB keyboard two HID devices.</td><br />
</tr><br />
<tr><br />
<td>MSC</td><br />
<td>Use DevKit407 as MSC (Mass Storage Device) Host, it can recognize U disc and some other mobile storage devices.</td><br />
</tr><br />
</table><br/><br/><br />
<br />
Table 1-2 RTOS & GUI BSP<br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td width="30%">STM32F4xx-uCOS-II</td><br />
<td>uC/OS-II-v2.86 BSP Drive</td><br />
</tr><br />
<tr><br />
<td>STM32F4xx-uCOSII-uCGUI</td><br />
<td>uC/OS-II-v2.86 & uC/GUI-v3.90a BSP Drive</td><br />
</tr><br />
</table></div>Cathyliddhttps://elinux.org/index.php?title=DM-STF4BB_Base_Board&diff=189986DM-STF4BB Base Board2012-11-07T14:10:36Z<p>Cathylidd: </p>
<hr />
<div>'''&nbsp;&nbsp;&nbsp;&nbsp;Base Board for STM32F4DISCOVERY STM32F4 High-performance Discovery Board<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Extended Peripherals including UART, Ethernet, CAN, Camera, LCD/TSP, TF, SPI, I2C…<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports Optional 3.5 inch LCD Module and 1.3 Megapixel Digital Camera Module<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports uC/OS-II_v2.86 & UCGUI_v3.90a<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports FatFs_vR0.08a File System (Used for TF card)<br />
'''<br/>&nbsp;&nbsp;&nbsp;&nbsp;Supports LwIP_v1.3.2 Protocol Stack<br />
<br/>[[File:Figure 1-1 DM-STF4BB Base Board.jpg]]<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The DM-STF4BB Base Board from Embest is an expansion board designed especially for STMicroelectronics’ STM32F4DISCOVERY high-performance discovery board which is based on the STM32F407VGT6 ARM Cortex-M4 microcontroller and includes an ST-LINK/V2 embedded debug tool, two ST MEMS, digital accelerometer and digital microphone, one audio DAC with integrated class D speaker driver, LEDs and push buttons and an USB OTG micro-AB connector on board.<br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;The DM-STF4BB Base Board enables the STM32F4DISCOVERY board users to further discover more features of the STM32F4. It has incorporated additional functionalities to the STF32F4DISCOVERY providing Serial ports, USB, Ethernet, CAN, SPI, I2C, GPIO, Camera, TF Card, LCD and Touch Screen interfaces on board. The combination of the DM-STF4BB and the STM32F4DISCOVERY forms an ideal evaluation board Devkit407 for evaluating the STM32F4xx series ARM Cortex-M4 microcontrollers and allows easy prototyping of third party solutions with STM32F4DISCOVERY board or STM32F4xx series microcontrollers.<br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;Embest has ported uC/OS-II to the DevKit407 board and the software also features the GUI support on uC/OS-II and LwIP_v1.3.2 protocal support. Meanwhile, Embest has offered rich software examples for DevKit407 besides those provided by STM32F4DISCOVERY kit. Along with the goods deliveries, Embest provides a CD containing the uC/OS-II BSP and plenty of software examples, board schematic and user manual to help customer better understanding this board and develop their own applications. <br />
<br />
&nbsp;&nbsp;&nbsp;&nbsp;Moreover, Embest offers one 3.5 inch LCD Module DM-LCD35RT (including touch screen) and one 1.3 megapixel Digital Camera Modules for options to implement the video input and output performance on DevKit407<br />
<br/>[[File:Figure 1-2 DevKit407.jpg]]<br />
<br/><br/><br />
&nbsp;&nbsp;&nbsp;The STMicroelectronics’ STM32F4DISCOVERY board is mounted directly on top of the DM-STF4BB base board to form an evaluation board DevKit407 for STM32F4xx series microcontrollers. The features of the DevKit407 are as following:<br />
<br/>[[File:Figure 1-3.jpg]]<br />
<br/><br/><br />
'''STM32F4DISCOVERY Board (CPU board of DevKit407)<br />
* STM32F407VGT6 microcontroller featuring 32-bit ARM Cortex-M4F core, 1 MB Flash,192KB RAM in an LQFP100 package<br/><br />
* On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone STLINK/V2 (with SWD connector for programming and debugging)<br/><br />
* Board power supply: through USB bus or from an external 5 V supply voltage<br/><br />
* External application power supply: 3 V and 5 V<br/><br />
* LIS302DL, ST MEMS motion sensor, 3-axis digital output accelerometer<br/><br />
* MP45DT02, ST MEMS audio sensor, omni-directional digital microphone<br/><br />
* CS43L22, audio DAC with integrated class D speaker driver<br/><br />
* Eight LEDs:<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;LD1 (red/green) for USB communication<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;LD2 (red) for 3.3 V power on<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;Four user LEDs, LD3 (orange), LD4 (green), LD5 (red) and LD6 (blue)<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;2 USB OTG LEDs LD7 (green) VBus and LD8 (red) over-current<br/><br />
* Two push buttons (user and reset)<br/><br />
* USB OTG FS with micro-AB connector<br/><br />
* Extension header for all LQFP100 I/Os for quick connection to prototyping board and easy probing.<br/><br />
<br/><br />
'''DM-STF4BB Base Board (Expansion Board of DevKit407)<br/><br />
* Working and Storage Temp.: 0~45°C<br/><br />
* Power consumption: +5V@80mA (working without LCD)<br/><br />
* Dimensions: 97.03mm x 83mm<br/><br />
* LCD parallel interface, 16-bit, 8080 mode<br/><br />
* 4-wire resistive touch screen interface<br/><br />
* Camera interface (support 1.3 megapixel Digital Camera, multiplex with UART6)<br/><br />
* One RS232 Serial port (UART6, DB9 connector, multiplex with Camera interface, can be selected by jumpers JP1 and JP2)<br/><br />
* One USB2.0 FS OTG/device/host port (12Mbps, Micro-AB type connector)<br/><br />
* One 10/100Mbps Ethernet Interface<br/><br />
* One 2.54mm pitch 2*20-pin expansion connector brought out below hardware peripherals:<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;5 Serial ports, TTL voltage (multiplex with some functions)<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;4-channel PWM<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;1-channel SPI<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;1-channel I2C<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;1 CAN2.0B interface (need to extend CAN transceivers)<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-&nbsp;&nbsp;6 GPIOs<br/><br/><br />
[[File:Figure 1-5.jpg]]<br/><br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;The DM-STF4BB base board offers features in addition to those provided by STM32F4DISCOVERY board that has exposed more features of the STMicroelectronics’ STM32F407VGT6 microcontroller through connectors or headers. <br/><br/><br />
[[File:Figure 1-6.jpg]]<br/><br/><br />
'''Features<br/><br />
The DevKit407 software mainly features as below:<br/><br />
* Supports for uC/OS-II_v2.86 operating system<br/><br />
* Supports UCGUI_v3.90a<br/><br />
* Supports FatFs_vR0.08a file system<br/><br />
* Supports LWIP _v1.3.2 protocol stack<br/><br />
'''Development Environment Support<br/><br />
* IAR EWARM<br />
&nbsp;&nbsp;&nbsp;&nbsp;All drivers support IAR EWARM, the EWARM version should be V6.40 or above.<br />
&nbsp;&nbsp;&nbsp;&nbsp;uC/OS-II and uC-GUI Demos do not support IAR EWARM at present.<br/><br />
* Keil MDK-ARM<br />
&nbsp;&nbsp;&nbsp;&nbsp;All drivers and applications support Keil MDK-ARM, the MDK-ARM version should be V4.22a or above.<br/><br />
'''Debug Tools Support<br/><br />
* ULINK2<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;It would be best to use with Keil MDK-ARM.<br/><br />
* JLINK-V8<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;It would be best to use with IAR EWARM. <br/><br />
* ST-LINK/V2<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;It can be used with either Keil MDK-ARM or IAR EWARM. <br/><br/><br />
'''Drivers and Software examples<br/><br />
&nbsp;&nbsp;&nbsp;&nbsp;Embest has offered rich software examples for DevKit407 besides those provided by STM32F4DISCOVERY kit such as examples for USB, Ethernet and so on. Meanwhile, Embest has provided some system-level application demos which can help customers get into the second development rapidly to reduce the development time. Please check from below table to know more about the drivers and software examples provided by Embest.<br/><br/><br />
<br />
Table 1-1 Drivers and Application Demos<br/><br />
<table border=1 width="70%"><br />
<tr><br />
<td width="15%">01-USART</td><br />
<td width="25%">USART_Printf</td><br />
<td>Hyper-Terminal Input/Output example</td><br />
</tr><br />
<tr><br />
<td rowspan='2'>02-SDIO</td><br />
<td>uSDCard</td><br />
<td>Read and write, erase of TF card example</td><br />
</tr><br />
<tr><br />
<td>FatFs</td><br />
<td>Port FatFs file system to TF card example</td><br />
</tr><br />
<tr><br />
<td rowspan='2'>03-LCD</td><br />
<td>LCD_35T</td><br />
<td>3.5 inch TFT LCD driver testing example</td><br />
</tr><br />
<tr><br />
<td>LCD_Touch</td><br />
<td>Touch screen testing example</td><br />
</tr><br />
<tr><br />
<td>04-DCMI</td><br />
<td>OV9655_Camera</td><br />
<td>DM-CAM130 module demo, can take photos</td><br />
</tr><br />
<tr><br />
<td colspan='3'>05-ETH_LwIP</td><br />
</tr><br />
<tr><br />
<td rowspan='5'>Standalone</td><br />
<td>httpserver</td><br />
<td>Webserver application demo</td><br />
</tr><br />
<tr><br />
<td>tcp_echo_client</td><br />
<td>Simple echo application demo of tcp customer end</td><br />
</tr><br />
<tr><br />
<td>tcp_echo_server</td><br />
<td>Simple echo application demo of tcp server end</td><br />
</tr><br />
<tr><br />
<td>udp_echo_client</td><br />
<td>Simple echo application demo of udp customer end</td><br />
</tr><br />
<tr><br />
<td>udp_echo_server</td><br />
<td>Simple echo application demo of udp server end</td><br />
</tr><br />
<tr><br />
<td rowspan='3'>FreeRTOS</td><br />
<td>httpserver_netconn</td><br />
<td>Webserver application demo based on netconn</td><br />
</tr><br />
<tr><br />
<td>Httpserver_socket</td><br />
<td>Webserver application demo based on socket</td><br />
</tr><br />
<tr><br />
<td>udptcp_echo_server_netconn</td><br />
<td>Echo application demo based on TCP/UDP server of netconn</td><br />
</tr><br />
<tr><br />
<td colspan='3'>06-USB</td><br />
</tr><br />
<tr><br />
<td rowspan='3'>USB_Device_Examples</td><br />
<td>DFU</td><br />
<td>Use DevKit407 as DFU equipment, user can use it for system firmware upgrading</td><br />
</tr><br />
<tr><br />
<td>MSC</td><br />
<td>Use DevKit407 as MSC (Mass Storage Device) to implement the data exchange between Host and evaluation board.</td><br />
</tr><br />
<tr><br />
<td>VCP</td><br />
<td>Use DevKit407 as VCP (Virtual COM Port) and user can regard the evaluation board as USB-to-UART converter module</td><br />
</tr><br />
<tr><br />
<td rowspan='2'>USB_Host_Examples</td><br />
<td>HID</td><br />
<td>Use DevKit407 as HID (Human Interaction Device) Host, it can recognize USB mouse and USB keyboard two HID devices.</td><br />
</tr><br />
<tr><br />
<td>MSC</td><br />
<td>Use DevKit407 as MSC (Mass Storage Device) Host, it can recognize U disc and some other mobile storage devices.</td><br />
</tr><br />
</table></div>Cathylidd