Difference between revisions of "A13 OLinuXino-MICRO"
Matt Porter (talk | contribs) (Created page with " == JTAG support == The A13 OLinuXino-MICRO has JTAG support brought out to an unpopulated 6-pin header next to the headphone jack. Solder a piece of header strip and it's re...") |
(And added to HOWTOs category) |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 27: | Line 27: | ||
=== BDI-2000/3000 === | === BDI-2000/3000 === | ||
| − | + | The [https://github.com/ohporter/bdi_configs/blob/master/a13-olinuxino-micro.cfg A13 OLinuXino-MICRO BDI config file] can be used with a BDI configured with the ARM11/Cortex-An firmware and the standard BDI ARM/Xscale 20-pin JTAG cable. | |
| − | [https://github.com/ohporter/ | + | [[File:Bdia13jtag.jpg|600px|BDI2000 to A13 OLinuXino JTAG cabling]] |
| + | |||
| + | === Flyswatter 2 / OpenOCD === | ||
| + | |||
| + | The [https://github.com/ohporter/openocd_configs/blob/master/a13-olinuxino.cfg A13 OLinuXino OpenOCD config file] can be used with a [[Flyswatter]], [[OpenOCD]], and the ARM 20-pin JTAG on the Flyswatter 2. | ||
| + | |||
| + | Usage: | ||
| + | |||
| + | openocd -f interface/flyswatter2.cfg -f /tmp/a13-olinuxino.cfg | ||
| + | |||
| + | [[File:Fs2a13jtag.jpg|600px|Flyswatter 2 to A13 OLinuXino JTAG cabling]] | ||
| + | |||
| + | [[Category:Flyswatter]] | ||
| + | [[Category:HOWTOs]] | ||
Revision as of 18:30, 30 April 2013
JTAG support
The A13 OLinuXino-MICRO has JTAG support brought out to an unpopulated 6-pin header next to the headphone jack. Solder a piece of header strip and it's ready to go.
Cabling
The table below shows the pinout for the proprietary JTAG header on the board. All pins are clearly silkscreened on the bottom of the board.
| A13 OLinuXino JTAG | Pin | JTAG Signal | ARM 20-pin JTAG | ARM 14-pin |
|---|---|---|---|---|
| GND | 1 | GND | 10 | 10 |
| TDO | 2 | TDO | 13 | 11 |
| TCK | 3 | TCK | 9 | 9 |
| TMS | 4 | TMS | 7 | 7 |
| TDI | 5 | TDI | 5 | 5 |
| 3.3V | 6 | 3.3V | 1 | 1 |
BDI-2000/3000
The A13 OLinuXino-MICRO BDI config file can be used with a BDI configured with the ARM11/Cortex-An firmware and the standard BDI ARM/Xscale 20-pin JTAG cable.
Flyswatter 2 / OpenOCD
The A13 OLinuXino OpenOCD config file can be used with a Flyswatter, OpenOCD, and the ARM 20-pin JTAG on the Flyswatter 2.
Usage:
openocd -f interface/flyswatter2.cfg -f /tmp/a13-olinuxino.cfg
