Difference between revisions of "Adafruit: 8x8 Blue LED Matrix Panel"
m (→Overview) |
m (→Inputs and Outputs) |
||
Line 17: | Line 17: | ||
== Inputs and Outputs == | == Inputs and Outputs == | ||
− | The LED Matrix uses an i2c port. Here is the hardware configuration of the Beagle Bone as shown below. Wire up the LED | + | The LED Matrix uses an i2c port. Here is the hardware configuration of the Beagle Bone as shown below. Wire up the LED Maxtrix to the Beagle by attaching the Vdd to the 3.3V '''+''' bus, the GND to the '''-''' bus and SDA to SDA (pin 20) and SCLK to SCL (pin 19). '''You will also need to attach two pull-up resistors'''. Get two 4.7KΩ resistors. Attach one between SDA and Vdd. Attach the other between SCL and Vdd. |
[[File:Bone gpio.JPG|300px]] | [[File:Bone gpio.JPG|300px]] | ||
[[File:BoneGPIO.png|300px]] | [[File:BoneGPIO.png|300px]] | ||
− | |||
== Software == | == Software == |
Revision as of 13:11, 17 October 2012
Overview
Overview: 2 Wiring: 2 Code: 2 git/Compiles with make: 2 gcc works Demo: 2 Total: 10 Comments: Looks good.
This Mini Project dealt with using Adafruit's 8x8 Blue LED Matrix. The source code they provided is written for Arduino. However, I am using the Beagle Bone instead. Luckily, Dr. Yoder has provided an example program called matrixLEDi2c.c that interfaces the Beagle. You can download or observe his source code here: Dr. Yoder's github repository. I editted this code to retain most of Dr. Yoder's original code, plus I added a design of my own. You can download my updated version from jungeml's github repository.
Inputs and Outputs
The LED Matrix uses an i2c port. Here is the hardware configuration of the Beagle Bone as shown below. Wire up the LED Maxtrix to the Beagle by attaching the Vdd to the 3.3V + bus, the GND to the - bus and SDA to SDA (pin 20) and SCLK to SCL (pin 19). You will also need to attach two pull-up resistors. Get two 4.7KΩ resistors. Attach one between SDA and Vdd. Attach the other between SCL and Vdd.
Software
I only changed code in 'matrixLEDi2c.c' file. I added my own design and also turned off the Matrix when the program was finished. As seen below:
/* my2cset.c - First try at controlling Adafruit 8x8matrix. Mark A. Yoder, 14-Aug-2012. Page numbers are from the HT16K33 manual http://www.adafruit.com/datasheets/ht16K33v110.pdf i2cset.c - A user-space program to write an I2C register. Copyright (C) 2001-2003 Frodo Looijaard <frodol@dds.nl>, and Mark D. Studebaker <mdsxyz123@yahoo.com> Copyright (C) 2004-2010 Jean Delvare <khali@linux-fr.org> This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. */ #include <errno.h> #include <string.h> #include <stdio.h> #include <stdlib.h> #include <unistd.h> #include "i2c-dev.h" #include "i2cbusses.h" static void help(void) __attribute__ ((noreturn)); static void help(void) { fprintf(stderr, "Usage: my2cset (hardwired to bus 3, address 0x70)\n"); exit(1); } static int check_funcs(int file, int size) { unsigned long funcs; /* check adapter functionality */ if (ioctl(file, I2C_FUNCS, &funcs) < 0) { fprintf(stderr, "Error: Could not get the adapter " "functionality matrix: %s\n", strerror(errno)); return -1; } switch (size) { case I2C_SMBUS_BYTE: if (!(funcs & I2C_FUNC_SMBUS_WRITE_BYTE)) { fprintf(stderr, MISSING_FUNC_FMT, "SMBus send byte"); return -1; } break; case I2C_SMBUS_BYTE_DATA: if (!(funcs & I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) { fprintf(stderr, MISSING_FUNC_FMT, "SMBus write byte"); return -1; } break; case I2C_SMBUS_WORD_DATA: if (!(funcs & I2C_FUNC_SMBUS_WRITE_WORD_DATA)) { fprintf(stderr, MISSING_FUNC_FMT, "SMBus write word"); return -1; } break; case I2C_SMBUS_BLOCK_DATA: if (!(funcs & I2C_FUNC_SMBUS_WRITE_BLOCK_DATA)) { fprintf(stderr, MISSING_FUNC_FMT, "SMBus block write"); return -1; } break; case I2C_SMBUS_I2C_BLOCK_DATA: if (!(funcs & I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) { fprintf(stderr, MISSING_FUNC_FMT, "I2C block write"); return -1; } break; } return 0; } int main(int argc, char *argv[]) { int res, i2cbus, address, size, file; int value, daddress; char filename[20]; int force = 0, readback = 1; __u16 block[I2C_SMBUS_BLOCK_MAX]; int len; i2cbus = lookup_i2c_bus("3"); printf("i2cbus = %d\n", i2cbus); if (i2cbus < 0) help(); address = parse_i2c_address("0x70"); printf("address = 0x%2x\n", address); if (address < 0) help(); size = I2C_SMBUS_BYTE; daddress = 0x21; if (daddress < 0 || daddress > 0xff) { fprintf(stderr, "Error: Data address invalid!\n"); help(); } file = open_i2c_dev(i2cbus, filename, sizeof(filename), 0); printf("file = %d\n", file); if (file < 0 || check_funcs(file, size) || set_slave_addr(file, address, force)) exit(1); switch (size) { case I2C_SMBUS_BYTE: daddress = 0x21; // Start oscillator (page 10) printf("writing: 0x%02x\n", daddress); res = i2c_smbus_write_byte(file, daddress); daddress = 0x81; // Display on, blinking off (page 11) printf("writing: 0x%02x\n", daddress); res = i2c_smbus_write_byte(file, daddress); daddress = 0xe7; // Full brightness (page 15) printf("writing: 0x%02x\n", daddress); res = i2c_smbus_write_byte(file, daddress); daddress = 0x00; // Start writing to address 0 (page 13) printf("writing: 0x%02x\n", daddress); res = i2c_smbus_write_byte(file, daddress); int i; static __u16 smile_bmp[] = {0x3C, 0x42, 0x95, 0xA1, 0xA1, 0x95, 0x42, 0x3C}; static __u16 frown_bmp[]= {0x3C, 0x42, 0xA5, 0x91, 0x91, 0xA5, 0x42, 0x3C}; static __u16 neutral_bmp[]={0x3C, 0x42, 0x95, 0x91, 0x91, 0x95, 0x42, 0x3C}; static __u16 my_bmp[] = {0xA5, 0x42, 0xA5, 0xA5, 0xA5, 0xA5, 0x42, 0xA5}; /* * For some reason the display is rotated one column, so pre-unrotate the * data. */ for(i=0; i<8; i++) { block[i] = (smile_bmp[i]&0xfe) >>1 | (smile_bmp[i]&0x01) << 7; } res = i2c_smbus_write_i2c_block_data(file, daddress, 16, (__u8 *)block); sleep(2); // Display a new picture for(i=0; i<8; i++) { block[i] = (frown_bmp[i]&0xfe) >>1 | (frown_bmp[i]&0x01) << 7; } daddress = 0x00; printf("writing: 0x%02x\n", daddress); res = i2c_smbus_write_byte(file, daddress); res = i2c_smbus_write_i2c_block_data(file, daddress, 16, (__u8 *)block); sleep(1); // Display yet another picture for(i=0; i<8; i++) { block[i] = (neutral_bmp[i]&0xfe) >>1 | (neutral_bmp[i]&0x01) << 7; } daddress = 0x00; printf("writing: 0x%02x\n", daddress); res = i2c_smbus_write_byte(file, daddress); res = i2c_smbus_write_i2c_block_data(file, daddress, 16, (__u8 *)block); sleep(1); // Display my picture for(i=0; i<8; i++) { block[i] = (my_bmp[i]&0xfe) >>1 | (my_bmp[i]&0x01) << 7; } daddress = 0x00; printf("writing: 0x%02x\n", daddress); res = i2c_smbus_write_byte(file, daddress); res = i2c_smbus_write_i2c_block_data(file, daddress, 16, (__u8 *)block); sleep(5); // Closing file and turning off Matrix printf("Closing file and turning off the LED Matrix\n"); daddress = 0x20; //for(daddress = 0xef; daddress >= 0xe0; daddress--) { printf("writing: 0x%02x\n", daddress); res = i2c_smbus_write_byte(file, daddress); usleep(500000); // Sleep 0.5 seconds //} break; case I2C_SMBUS_WORD_DATA: res = i2c_smbus_write_word_data(file, daddress, value); break; case I2C_SMBUS_BLOCK_DATA: res = i2c_smbus_write_block_data(file, daddress, len, (const __u8 *)block); break; case I2C_SMBUS_I2C_BLOCK_DATA: res = i2c_smbus_write_i2c_block_data(file, daddress, len, (const __u8 *)block); break; default: /* I2C_SMBUS_BYTE_DATA */ res = i2c_smbus_write_byte_data(file, daddress, value); break; } if (res < 0) { fprintf(stderr, "Error: Write failed\n"); close(file); exit(1); } if (!readback) { /* We're done */ close(file); exit(0); } switch (size) { case I2C_SMBUS_BYTE: res = i2c_smbus_read_byte(file); value = daddress; break; case I2C_SMBUS_WORD_DATA: res = i2c_smbus_read_word_data(file, daddress); break; default: /* I2C_SMBUS_BYTE_DATA */ res = i2c_smbus_read_byte_data(file, daddress); } close(file); /*if (res < 0) { printf("Warning - readback failed\n"); } else if (res != value) { printf("Warning - data mismatch - wrote " "0x%0*x, read back 0x%0*x\n", size == I2C_SMBUS_WORD_DATA ? 4 : 2, value, size == I2C_SMBUS_WORD_DATA ? 4 : 2, res); } else { printf("Value 0x%0*x written, readback matched\n", size == I2C_SMBUS_WORD_DATA ? 4 : 2, value); } */ exit(0); }
This code example and the required resources can be found in jungeml's github repository