Difference between revisions of "Beagleboard:Caraneacancape"

From eLinux.org
Jump to: navigation, search
m (added cable spec)
m
Line 43: Line 43:
 
|}
 
|}
  
===Electrical Specifications===
+
===DB9 to OBD II===
 
{|class="wikitable"
 
{|class="wikitable"
 
|1
 
|1
Line 91: Line 91:
 
|-
 
|-
 
|}
 
|}
 
  
 
===Mechanical Specifications===
 
===Mechanical Specifications===

Revision as of 23:11, 7 May 2016

Descriptions

Caranea Can Cape

The Caranea Can Cape provides a CAN Bus and a internal power supply of 7-40V to run the BeagleBoardBlack as a CarComputer directly connected to the OBD II Port. You need a DB-9 to OBD II adapter cable to connect the Caranea Can Cape to the car. Be careful, never use again the internal 5V power supply of the BeagleBord anymore. The CAN Bus transceiver uses only one CAN channel and converts data from standard UART communication (RXD/TXD) to CAN communication (CANH/CANL). The CAN Bus operates under the J-2285 Protocol and can be wired like in table Adapter. With the internal Linux Driver you are up and running to build your own Application to communicate with the car. We also provide you with a much more complex software, which can extract all the data from car via a web service. For more information check our webpage Caranea.

FAQ

Please visit our Caranea page for additional help.

Revision 1

Initial release of Caranea Can Cape

Software Support

  • Caranea Can Cape is supported by Angstrom release 06-18-12 onward.
  • Major BeagleBone image releases can be downloaded here.
  • Intermediate BeagleBone image releases can be downloaded here

Getting Started

Required setup:

  • A Caranea Can Cape
  • A BeagleBone (with supported software)
  • DB-9 to OBD II Cable

Following the instructions below to start using your Caranea Can Cape:

  1. Mount the Caranea Can Cape to the connectors of the BeagleBone Black.
  2. Don't plug in a 5V DC power supply to the DC connector, use only 12V power supply via DB-9.
  3. Copy “CANCAPE-00A0.dtbo” file into /lib/firmware
  4. echo CANCAPE > /sys/devices/bone_capemgr.9/slots
  5. Type dmesg and you should see: mcp251x spi1.0: mode 0, irq 259, awake 1, clkout 1, oscillator freq 16000000 mcp251x spi1.0 can1: probed
  6. After you have to bring CAN0 interface up: ip link set can0 type can bitrate 125000, ip link set can0 up

You can start using the board.

Specifications

Followings are some specifications of the Caranea Can Cape:

Electrical Specifications

Power 7-42V via OBD II
CAN 1 CAN Bus Transreceiver

DB9 to OBD II

1 J1850 BUS+ 2 7
2 Chassis Ground 4 2
3 Signal Ground 5 1
4 CAN High J-2284 6 3
5 ISO 9141-2 K Line 7 4
6 J1850 BUS- 10 6
7 CAN Low J-2284 14 5
8 ISO 9141-2 L Line 15 8
9 Battery Power 16 9

Mechanical Specifications

Size 4.00" x 2.50"
Layers 4
PCB Thickness .062"

Signal Usage

Distributors

Product Images



Documentations

System Reference Manual

Hardware Files

To go back to the cape list, please click here