Building for BeagleBone

Revision as of 12:51, 25 June 2014 by Tanure (talk | contribs)
Jump to: navigation, search

Arm Compiler

Setting up cross-compile environment is the first and necessary step.

Distro provided

The easier way is install the default compiler provided by your distribution.

Ubuntu : gcc-arm-linux-gnueabi

Arch Linux : arm-linux-gnueabi-gcc

Debian : ??

Fedora : ??

Linux Mint : ??

  • Tip: Do a alias in your environment, where N is the number of processors cores plus one:
$ alias armmake='make -jN ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- '




Mainline U-boot

You can use the mainline u-boot for beaglebone.


$ git clone git://


$ armmake distclean

Configure for BeagleBone:

$ armmake am335x_evm_config


$ armmake

Test your new U-Boot

You need a microSd card with 2Gb or more. In order to make U-Boot work you will need to create the first partion as FAT32 LBA, bootable, with something like 64 Megabytes.
This command wipes everything from your sdcard and creates that partition.

$ echo -e "o\nn\np\n1\n\n+64M\na\n1\nt\nc\nw\n" | sudo fdisk /dev/MYDISK ; sudo fdisk /dev/MYDISK -l

This comand should print something like:

Disk /dev/sdb: 7948 MB, 7948206080 bytes
16 heads, 4 sectors/track, 242560 cylinders, total 15523840 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x1c524301
    Device Boot      Start         End      Blocks   Id  System
/dev/sdb1   *        2048      133119       65536    c  W95 FAT32 (LBA)

The U-Boot compilation generated two files, MLO and uboot.img. Mount the partition that you just created and copy FIRST the MLO file to partition. Then copy the u-boot.img.

$ sudo mount /dev/MYDISK /mnt
$ sudo cp MLO /mnt
$ sudo cp u-boot.img
$ sudo sync
$ sudo umount  /mnt
U-Boot SPL 2014.07-rc3-00136-gba9b42c (Jun 25 2014 - 14:36:07)
reading u-boot.img
reading u-boot.img

U-Boot 2014.07-rc3-00136-gba9b42c (Jun 25 2014 - 14:36:07)

I2C:   ready
DRAM:  512 MiB
NAND:  0 MiB
*** Warning - readenv() failed, using default environment

Net:   <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
SD/MMC found on device 0
reading uEnv.txt
9 bytes read in 4 ms (2 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
** Invalid partition 2 **
switch to partitions #0, OK
mmc1(part 0) is current device
SD/MMC found on device 1
reading uEnv.txt
26 bytes read in 4 ms (5.9 KiB/s)
Loaded environment from uEnv.txt
Importing environment from mmc ...
** File not found /zImage **
Booting from nand ...

no devices available

no devices available
Bad Linux ARM zImage magic!


Mainline Kernel


Test your new Kernel