Difference between revisions of "EBC Exercise 08 Installing Development Tools 3.8"

From eLinux.org
Jump to: navigation, search
m (Cleaned up commands)
(download)
(12 intermediate revisions by 3 users not shown)
Line 9: Line 9:
  
 
'''Tip:''' Run this exercise using a wired connection if you can. The Ubuntu wireless driver can be finicky, and if it stops working you'll have to restart some of this.
 
'''Tip:''' Run this exercise using a wired connection if you can. The Ubuntu wireless driver can be finicky, and if it stops working you'll have to restart some of this.
 +
 +
== The Kernel ==
  
 
These instructions have been tested for the 3.2.25 kernel.
 
These instructions have been tested for the 3.2.25 kernel.
  
 +
=== download ===
 
These are notes are based on [https://github.com/beagleboard/kernel/blob/6682025752d0b807119c1e363a0b1b9bfe2ab453/README.md Beagleboard kernel git site].
 
These are notes are based on [https://github.com/beagleboard/kernel/blob/6682025752d0b807119c1e363a0b1b9bfe2ab453/README.md Beagleboard kernel git site].
  
Line 20: Line 23:
 
  host$ '''cd ~/BeagleBoard'''
 
  host$ '''cd ~/BeagleBoard'''
 
  host$ '''git clone git://github.com/beagleboard/kernel.git'''
 
  host$ '''git clone git://github.com/beagleboard/kernel.git'''
 +
host$ '''cd kernel'''
 +
host$ '''git checkout 6a7c4284a16fed3dae87f4aef78b59c902e4da84 -b beaglebone-3.2'''
  
 
Next download the kernel and the patches.  Before running '''./patch/sh''', take a look at it.  Can you figure out what it's doing?  Also look at '''patch_script.sh''', it's where the details are. The downloading/patching process takes some 39 minutes.
 
Next download the kernel and the patches.  Before running '''./patch/sh''', take a look at it.  Can you figure out what it's doing?  Also look at '''patch_script.sh''', it's where the details are. The downloading/patching process takes some 39 minutes.
  host$ '''gedit patch.sh patch_script.sh'''
+
  host$ '''less patch.sh patch_script.sh'''
 
  host$ '''./patch.sh'''
 
  host$ '''./patch.sh'''
 +
host$ '''cp patches/beaglebone/defconfig kernel/arch/arm/configs/beaglebone_defconfig
 +
host$ '''wget http://arago-project.org/git/projects/?p=am33x-cm3.git\;a=blob_plain\;f=bin/am335x-pm-firmware.bin\;hb=HEAD -O kernel/firmware/am335x-pm-firmware.bin'''
 +
host$ '''md5sum kernel/firmware/am335x-pm-firmware.bin'''
 +
17d6a4c24d3cb720aa9ed4522cb891fc  kernel/firmware/am335x-pm-firmware.bin
  
 +
=== compile ===
 
Once patched you are ready to compile the kernel.  The first time takes a while.  Mine tool 4 minutes, but I was running on 8 cores.  Set the '''-j''X'' ''' to match the number of cores you have. '''uImage''' is the kernel!
 
Once patched you are ready to compile the kernel.  The first time takes a while.  Mine tool 4 minutes, but I was running on 8 cores.  Set the '''-j''X'' ''' to match the number of cores you have. '''uImage''' is the kernel!
 +
host$ '''cd kernel'''
 +
host$ '''make beaglebone_defconfig'''
 +
 +
Now that you know it's working, let's compile it. First set the paths to find the cross-compiles. Put the following in a file, call it ~/.oe/'''crossCompile.sh'''.
 +
 +
export ARCH=arm
 +
export CROSS_COMPILE=arm-linux-gnueabi-
 +
Do the above once
 +
 +
Now ''source'' the file.
 +
host$ '''source ~/.oe/crossCompileEnv.sh'''
 +
Do the above once per terminal session.
 +
 
  host$ '''make -j9'''
 
  host$ '''make -j9'''
 
  host$ '''make uImage'''
 
  host$ '''make uImage'''
 +
Do the above every time you recompile the kernel
  
 
You also need all the kernel modules.  Here we create a directory to install them in. (a few seconds)
 
You also need all the kernel modules.  Here we create a directory to install them in. (a few seconds)
  host$ '''mkdir rootfs'''
+
  host$ '''mkdir ../rootfs'''
  host$ '''make INSTALL_MOD_PATH=rootfs modules_install'''
+
  host$ '''make INSTALL_MOD_PATH=../rootfs modules_install'''
  
 +
=== install ===
 
Copy the kernel and the modules to the Beagle.  (a minute or so)
 
Copy the kernel and the modules to the Beagle.  (a minute or so)
 +
host$ '''cd ..'''
 
  host$ '''scp kernel/arch/arm/boot/uImage root@beagle:/boot/uImage-3.2.25+
 
  host$ '''scp kernel/arch/arm/boot/uImage root@beagle:/boot/uImage-3.2.25+
 
  host$ '''cd rootfs'''
 
  host$ '''cd rootfs'''
Line 40: Line 66:
 
Now log into the beagle and move some things around.
 
Now log into the beagle and move some things around.
 
  host$ '''ssh root@beagle
 
  host$ '''ssh root@beagle
 +
 +
This will copy the kernel to the ext4 partition.
 
  beagle$ '''cd /boot'''
 
  beagle$ '''cd /boot'''
 
  beagle$ '''rm uImage'''
 
  beagle$ '''rm uImage'''
 
  beagle$ '''ln -s uImage-3.2.25+ uImage'''
 
  beagle$ '''ln -s uImage-3.2.25+ uImage'''
 +
 +
This will copy to the FAT partition.
 
  beagle$ '''mkdir /media/mmcblk0p1'''
 
  beagle$ '''mkdir /media/mmcblk0p1'''
 
  beagle$ '''mount /dev/mmcblk0p1 /media/mmcblk0p1'''
 
  beagle$ '''mount /dev/mmcblk0p1 /media/mmcblk0p1'''
 
  beagle$ '''cp /boot/uImage-3.2.25+ /media/uImage'''
 
  beagle$ '''cp /boot/uImage-3.2.25+ /media/uImage'''
  
== Download and Compile U-boot ==
+
=== reboot ===
 +
Make sure screen is running on your host so you can see the shutdown and boot processes.
 +
host$ '''screen /dev/ttyUSB1 115200'''
  
While were' at it, let's get the boot loader we'll be using...
+
If you get an error try changing making yourself the owner of /dev/ttyUSB1.
 +
host$ '''sudo chown ''yoder:yoder'' /dev/ttyUSB1'''
 +
host$ '''screen /dev/ttyUSB1 115200'''
  
 +
Then restart you beagle
 +
beagle$ '''shutdown -r now'''
 +
 +
If all goes well you will boot into your new kernel.
 +
beagle$ '''uname -a'''
 +
Linux beaglebone 3.2.25+ #1 Fri Oct 19 11:05:28 EDT 2012 armv7l GNU/Linux
 +
 +
== DAS U-boot ==
 +
These instructions came from [http://www.eewiki.net/display/linuxonarm/Home eewiki].
 +
 +
=== download ===
 +
While we're at it, let's get the boot loader we'll be using.  It takes some 3 minutes.
 +
 +
host$ '''cd ~/BeagleBoard'''
 
  host$ '''git clone git://git.denx.de/u-boot.git'''
 
  host$ '''git clone git://git.denx.de/u-boot.git'''
 +
host$ '''cd u-boot/'''
 +
host$ '''git checkout v2012.10-rc2 -b tmp'''
  
Mine took about 3 minutes.
+
=== compile ===
 +
Now configure and build.  The first time takes some 4 minutes. After that it's only 5 seconds or so. (Replace '''am335x_evm_config''' with '''omap3_beagle_config''' if you are compiling for the xM.)
 +
host$ '''make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- am335x_evm_config'''
 +
host$ '''make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi-'''
  
Once installed you are ready for kernel work.
+
=== install ===
 +
 
 +
host$ '''scp u-boot.img root@beagle:.'''
 +
beagle$ '''mkdir /media/mmcblk0p1'''
 +
beagle$ '''mount /dev/mmcblk0p1 /media/mmcblk0p1'''
 +
beagle$ '''cd /media/mmcblk0p1'''
 +
beagle$ '''mv u-boot.img u-boot.img.orig'''  # Save the working u-boot
 +
beagle$ '''cp ~/u-boot.img u-boot.img.new'''
 +
beagle$ '''cp u-boot.img.new u-boot.img'''
 +
Once installed you are ready for u-boot work.
  
 
{{YoderFoot}}
 
{{YoderFoot}}

Revision as of 12:28, 5 November 2012

thumb‎ Embedded Linux Class by Mark A. Yoder


Early in the class most of the exercises we will do will all run on the BeagleBoard. You'll be able to edit (gedit), compile (gcc) and run all on the Beagle. Later, when we start compiling the kernel [1] or the boot loader, (U-boot) you will need to cross compile on a Linux machine and copy the results to the Beagle.

The purpose of this exercise is to install all the tools needed for compiling on your host so they will be ready when you need them.

Instructions for building Ångström are given here; however there are a few changes you have to make. Here's what I did.

Tip: Run this exercise using a wired connection if you can. The Ubuntu wireless driver can be finicky, and if it stops working you'll have to restart some of this.

The Kernel

These instructions have been tested for the 3.2.25 kernel.

download

These are notes are based on Beagleboard kernel git site.

First download the tools needed to compile the kernel. This took about 25 seconds.

host$ sudo apt-get install -y git lzop gcc-arm-linux-gnueabi uboot-mkimage

Next download the tools to get the kernel and the patches needed to make it run on the beagle. (2.5 seconds)

host$ cd ~/BeagleBoard
host$ git clone git://github.com/beagleboard/kernel.git
host$ cd kernel
host$ git checkout 6a7c4284a16fed3dae87f4aef78b59c902e4da84 -b beaglebone-3.2

Next download the kernel and the patches. Before running ./patch/sh, take a look at it. Can you figure out what it's doing? Also look at patch_script.sh, it's where the details are. The downloading/patching process takes some 39 minutes.

host$ less patch.sh patch_script.sh
host$ ./patch.sh
host$ cp patches/beaglebone/defconfig kernel/arch/arm/configs/beaglebone_defconfig
host$ wget http://arago-project.org/git/projects/?p=am33x-cm3.git\;a=blob_plain\;f=bin/am335x-pm-firmware.bin\;hb=HEAD -O kernel/firmware/am335x-pm-firmware.bin
host$ md5sum kernel/firmware/am335x-pm-firmware.bin 
17d6a4c24d3cb720aa9ed4522cb891fc  kernel/firmware/am335x-pm-firmware.bin

compile

Once patched you are ready to compile the kernel. The first time takes a while. Mine tool 4 minutes, but I was running on 8 cores. Set the -jX to match the number of cores you have. uImage is the kernel!

host$ cd kernel
host$ make beaglebone_defconfig

Now that you know it's working, let's compile it. First set the paths to find the cross-compiles. Put the following in a file, call it ~/.oe/crossCompile.sh.

export ARCH=arm
export CROSS_COMPILE=arm-linux-gnueabi-

Do the above once

Now source the file.

host$ source ~/.oe/crossCompileEnv.sh

Do the above once per terminal session.

host$ make -j9
host$ make uImage

Do the above every time you recompile the kernel

You also need all the kernel modules. Here we create a directory to install them in. (a few seconds)

host$ mkdir ../rootfs
host$ make INSTALL_MOD_PATH=../rootfs modules_install

install

Copy the kernel and the modules to the Beagle. (a minute or so)

host$ cd ..
host$ scp kernel/arch/arm/boot/uImage root@beagle:/boot/uImage-3.2.25+
host$ cd rootfs
host$ find -H -depth | cpio -o -H crc | ssh root@beagle 'cd /; cpio -id' 

Now log into the beagle and move some things around.

host$ ssh root@beagle

This will copy the kernel to the ext4 partition.

beagle$ cd /boot
beagle$ rm uImage
beagle$ ln -s uImage-3.2.25+ uImage

This will copy to the FAT partition.

beagle$ mkdir /media/mmcblk0p1
beagle$ mount /dev/mmcblk0p1 /media/mmcblk0p1
beagle$ cp /boot/uImage-3.2.25+ /media/uImage

reboot

Make sure screen is running on your host so you can see the shutdown and boot processes.

host$ screen /dev/ttyUSB1 115200

If you get an error try changing making yourself the owner of /dev/ttyUSB1.

host$ sudo chown yoder:yoder /dev/ttyUSB1
host$ screen /dev/ttyUSB1 115200

Then restart you beagle

beagle$ shutdown -r now

If all goes well you will boot into your new kernel.

beagle$ uname -a
Linux beaglebone 3.2.25+ #1 Fri Oct 19 11:05:28 EDT 2012 armv7l GNU/Linux

DAS U-boot

These instructions came from eewiki.

download

While we're at it, let's get the boot loader we'll be using. It takes some 3 minutes.

host$ cd ~/BeagleBoard
host$ git clone git://git.denx.de/u-boot.git
host$ cd u-boot/
host$ git checkout v2012.10-rc2 -b tmp

compile

Now configure and build. The first time takes some 4 minutes. After that it's only 5 seconds or so. (Replace am335x_evm_config with omap3_beagle_config if you are compiling for the xM.)

host$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- am335x_evm_config
host$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi-

install

host$ scp u-boot.img root@beagle:.
beagle$ mkdir /media/mmcblk0p1
beagle$ mount /dev/mmcblk0p1 /media/mmcblk0p1
beagle$ cd /media/mmcblk0p1
beagle$ mv u-boot.img u-boot.img.orig  # Save the working u-boot
beagle$ cp ~/u-boot.img u-boot.img.new
beagle$ cp u-boot.img.new u-boot.img

Once installed you are ready for u-boot work.




thumb‎ Embedded Linux Class by Mark A. Yoder