|
|
| (24 intermediate revisions by 3 users not shown) |
| Line 1: |
Line 1: |
| − | = hp712, HP 9000/712 model =
| |
| | | | |
| − | == Overview ==
| |
| − |
| |
| − |
| |
| − | == Changing to Serial Console ==
| |
| − |
| |
| − | WARNING: Improper setting of the console path may cause the system to become inoperable. Beware.
| |
| − |
| |
| − | Unfortunately, HP decided that the 712 should be hard to configure for headless use.
| |
| − |
| |
| − | Briefly, you must get to the HP-UX bootloader prompt (which they call the ISL) which will allow you to permanently set your preferred console location to the first serial port at 9600 8N1.
| |
| − |
| |
| − | The original source of this information is http://lists.parisc-linux.org/pipermail/parisc-linux/1999-December/008117.html.
| |
| − |
| |
| − | To change to a serial console, you need:
| |
| − |
| |
| − | * a PS/2 style keyboard
| |
| − | * a monitor with VGA style interface
| |
| − | * the HP-UX ISL (either an HP-UX bootable hard drive or netboot)
| |
| − |
| |
| − | First, you need to get to the BootROM prompt. When your system prints the following on screen, press and hold ESC until you get the BOOT_ADMIN> prompt:
| |
| − |
| |
| − | Press <ESCAPE> to stop boot sequence.
| |
| − |
| |
| − | === Setting monitor type ===
| |
| − |
| |
| − | If your display doesn't show properly, the frequency may be out-of-range. You can select the monitor type suitable to your display.
| |
| − |
| |
| − | If your 712 has the add-in VRAM board, normal VGA 680x480 mode is monitor type 7. Without the VRAM board, the number may be different (possibly 5?).
| |
| − |
| |
| − | BOOT_ADMIN> monitor 7
| |
| − | Monitor Choices
| |
| − | Type Resolution Frequency
| |
| − | ---- ---------- ---------
| |
| − | 1 1280x1024 72Hz
| |
| − | 2 1024x768 75Hz
| |
| − | 3 1024x768 70Hz
| |
| − | 4 1024x768 75Hz Flat Panel
| |
| − | 5 1280x1024 60Hz
| |
| − | 6 1024x768 60Hz
| |
| − | 7 640x480 60Hz
| |
| − | 8 1280x1024 75Hz VESA
| |
| − | 9 1024x768 75Hz VESA
| |
| − | 10 800x600 75Hz VESA
| |
| − | 11 640x480 75Hz VESA
| |
| − | 12 1280x1024 72Hz Greyscale
| |
| − | 13 1280x1024 50Hz
| |
| − |
| |
| − | Current Monitor Type is
| |
| − | 7 640x480 60Hz
| |
| − |
| |
| − | BOOT_ADMIN> reset
| |
| − |
| |
| − | Step 2, Case 1: If you have HP-UX installed on local disk
| |
| − |
| |
| − | BOOT_ADMIN> boot pri isl
| |
| − |
| |
| − | Booting
| |
| − |
| |
| − | ISL Revision A.00.38 OCT 26, 1994
| |
| − |
| |
| − |
| |
| − | ISL>
| |
| − |
| |
| − | === Boot 712 from LAN ===
| |
| − |
| |
| − | BOOT_ADMIN> boot lan isl
| |
| − |
| |
| − | Booting
| |
| − |
| |
| − | ISL Revision A.00.25 November 18, 1992
| |
| − |
| |
| − |
| |
| − | ISL>
| |
| − |
| |
| − | === Setting console location ===
| |
| − |
| |
| − | Run the following command to set your 712 to use a serial console:
| |
| − |
| |
| − | ISL> conspath 2/0/4.0x283
| |
| − |
| |
| − | To set your 712 to use the local console (i.e. keyboard and screen), run the following command:
| |
| − |
| |
| − | ISL> conspath 1/0/0.0
| |
| − |
| |
| − | You can use the display and information commands to verify that your settings have been stored properly. Once you're sure everything looks right, power cycle your workstation to start using your serial console.
| |
| − |
| |
| − | Additionally, you can temporarily use the local console by pressing the “Esc” key on the PS/2 keyboard while resetting. This is setting only affects the console location temporarily and only works with firmware rev 1.6 and later.
| |
| − |
| |
| − |
| |
| − | === Shot Example ===
| |
| − |
| |
| − | <pre>
| |
| − | ----------------------------------------------------------------------------
| |
| − | BootRom Version 1.6
| |
| − |
| |
| − | Memory Size: 64 MB
| |
| − | ----------------------------------------------------------------------------
| |
| − |
| |
| − |
| |
| − |
| |
| − |
| |
| − | (c) Copyright 1990-1993, Hewlett-Packard Company.
| |
| − | All rights reserved
| |
| − |
| |
| − | Press <ESCAPE> to stop boot sequence.
| |
| − | <ESC>
| |
| − | Selecting a system to boot.
| |
| − | ----------------------------------------------------------------------------
| |
| − | Command Description
| |
| − | ------- -----------
| |
| − | Auto [boot|search] [on|off] Display or set auto flag
| |
| − | Boot [pri|alt|scsi.addr] [isl] Boot from primary, alternate or SCSI
| |
| − | Boot lan[.lan_addr] [install] [isl] Boot from LAN
| |
| − | Chassis [on|off] Enable chassis codes
| |
| − | Diagnostic [on|off] Enable/disable diagnostic boot mode
| |
| − | Fastboot [on|off] Display or set fast boot flag
| |
| − | Help Display the command menu
| |
| − | Information Display system information
| |
| − | LanAddress Display LAN station addresses
| |
| − | Monitor [type] Select monitor type
| |
| − | Path [pri|alt] [lan.id|SCSI.addr] Change boot path
| |
| − | Pim [hpmc|toc|lpmc] Display PIM info
| |
| − | Search [ipl] [scsi|lan [install]] Display potential boot devices
| |
| − | Secure [on|off] Display or set security mode
| |
| − | ----------------------------------------------------------------------------
| |
| − | BOOT_ADMIN> monitor 7
| |
| − | Monitor Choices
| |
| − | Type Resolution Frequency
| |
| − | ---- ---------- ---------
| |
| − | 1 1280x1024 72Hz
| |
| − | 2 1024x768 75Hz
| |
| − | 3 1024x768 70Hz
| |
| − | 4 1024x768 75Hz Flat Panel
| |
| − | 5 1280x1024 60Hz
| |
| − | 6 1024x768 60Hz
| |
| − | 7 640x480 60Hz
| |
| − | 8 1280x1024 75Hz VESA
| |
| − | 9 1024x768 75Hz VESA
| |
| − | 10 800x600 75Hz VESA
| |
| − | 11 640x480 75Hz VESA
| |
| − | 12 1280x1024 72Hz Greyscale
| |
| − | 13 1280x1024 50Hz
| |
| − |
| |
| − | Current Monitor Type is
| |
| − | 7 640x480 60Hz
| |
| − |
| |
| − | BOOT_ADMIN> reset
| |
| − |
| |
| − | ----------------------------------------------------------------------------
| |
| − | BootRom Version 1.6
| |
| − |
| |
| − | Memory Size: 64 MB
| |
| − | ----------------------------------------------------------------------------
| |
| − |
| |
| − |
| |
| − |
| |
| − |
| |
| − | (c) Copyright 1990-1993, Hewlett-Packard Company.
| |
| − | All rights reserved
| |
| − |
| |
| − | Press <ESCAPE> to stop boot sequence.
| |
| − | <ESC>
| |
| − | Selecting a system to boot.
| |
| − | ----------------------------------------------------------------------------
| |
| − | Command Description
| |
| − | ------- -----------
| |
| − | Auto [boot|search] [on|off] Display or set auto flag
| |
| − | Boot [pri|alt|scsi.addr] [isl] Boot from primary, alternate or SCSI
| |
| − | Boot lan[.lan_addr] [install] [isl] Boot from LAN
| |
| − | Chassis [on|off] Enable chassis codes
| |
| − | Diagnostic [on|off] Enable/disable diagnostic boot mode
| |
| − | Fastboot [on|off] Display or set fast boot flag
| |
| − | Help Display the command menu
| |
| − | Information Display system information
| |
| − | LanAddress Display LAN station addresses
| |
| − | Monitor [type] Select monitor type
| |
| − | Path [pri|alt] [lan.id|SCSI.addr] Change boot path
| |
| − | Pim [hpmc|toc|lpmc] Display PIM info
| |
| − | Search [ipl] [scsi|lan [install]] Display potential boot devices
| |
| − | Secure [on|off] Display or set security mode
| |
| − | ----------------------------------------------------------------------------
| |
| − | BOOT_ADMIN> boot lan isl
| |
| − |
| |
| − | Booting
| |
| − |
| |
| − | ISL Revision A.00.25 November 18, 1992
| |
| − |
| |
| − |
| |
| − | ISL> display
| |
| − |
| |
| − | Fastsize value is 0000000F
| |
| − |
| |
| − | Autoboot is ON (enabled)
| |
| − |
| |
| − | Autosearch is ON (enabled)
| |
| − |
| |
| − | Primary boot path is 2/0/1.6.0.0.0.0.0
| |
| − | Primary boot path is (hex) 2/0/1.6.0.0.0.0.0
| |
| − |
| |
| − | Alternate boot path is 2/0/2.0.0.0.0.0.0
| |
| − | Alternate boot path is (hex) 2/0/2.0.0.0.0.0.0
| |
| − |
| |
| − | System console path is 1.0.0.0.0.0.0
| |
| − | System console path is (hex) 1.0.0.0.0.0.0
| |
| − |
| |
| − | ISL> conspath 2/0/4.0x283
| |
| − |
| |
| − | ISL> display
| |
| − |
| |
| − | Fastsize value is 0000000F
| |
| − |
| |
| − | Autoboot is ON (enabled)
| |
| − |
| |
| − | Autosearch is ON (enabled)
| |
| − |
| |
| − | Primary boot path is 2/0/1.6.0.0.0.0.0
| |
| − | Primary boot path is (hex) 2/0/1.6.0.0.0.0.0
| |
| − |
| |
| − | Alternate boot path is 2/0/2.0.0.0.0.0.0
| |
| − | Alternate boot path is (hex) 2/0/2.0.0.0.0.0.0
| |
| − |
| |
| − | System console path is 2/0/4.643.0.0.0.0.0
| |
| − | System console path is (hex) 2/0/4.283.0.0.0.0.0
| |
| − |
| |
| − | ISL>
| |
| − | </pre>
| |
| − |
| |
| − | Then, cycle the power.
| |
| − | Back to NetBSD/hp700 Port Page
| |
| − | Contact | Disclaimer | Copyright © 1994-2009 The NetBSD Foundation, Inc. ALL RIGHTS RESERVED.
| |
| − | NetBSD® is a registered trademark of The NetBSD Foundation, Inc.
| |
