hp712, HP 9000/712 model
Time of introduction: 1994
The PA-7100LC was primarily designed as a single-chip solution for application in low cost systems while still delivering the performance of 1991 high-end workstations and servers. The CPU core design was leveraged from the PA-7100 and integrated with several of its off-chip support components on a single die. The PA-7100LC integrates the CPU, FPU, MIOC (memory and I/O controller) and a first-level cache on a single VLSI chip and has a direct attachment to the GSC main bus. Both CPU and FPU support the PA-RISC 1.1 Edition 3 ISA. Details
- PA-RISC version 1.1c 32-bit
- Three functional units: 2 integer ALUs, 1 Floating Point unit1
- 2-way superscalar
- Not SMP-capable
- Five-stage pipeline
- DRAM memory & cache controller (MIOC) integrated on die, thus direct interface from the CPU to memory and cache
- 1KB on-chip I L1 instruction cache, direct mapped, 64-bit per access, prefetch from off-chip I cache
- 8KB-2MB off-chip unified I/D L1 cache, direct mapped, hashed address, virtual index, 480-600MB/s bandwidth
- The 1KB on-chip I cache is not really considered a true cache, thus the off-chip cache in fact is the system’s real L1 cache
- 32-Byte cache line size
- Support for bi-endian load-store operations
- MAX-1 multimedia extensions (subword arithmetic) for multimedia applications, e.g., MPEG decoding
- Floating Point load-store to I/O space
- 64-entry unified I/D TLB, fully associative, 4K page size
- 8-entry BTLB, page sizes from 512K - 64M
- 64-bit wide load/store operations
- I and D cache bypassing
- Stall on use D cache miss policy
- Don’t fill on miss cache hint
- Hardware TLB miss handler support
- Hardware static branch prediction
- GSC bus interface
- 64-bit ECC interface to the main memory
- Instruction line prefetch from main memory
- Up to 100MHz clock
- 14.2×14.2 mm2 die, 900,000 FETs, 0.75µ (micron), 3-layer aluminium process packaged in a 432-pin PGA
Only one of the two integer ALUs is able to handle loads, stores and shifts, these operations can only be paired with simple math operations, like integer addition or multiplication. Both units can handle branch operations.
1. PA7100LC ERS (External Reference Specification)Link 11 (.pdf) Hewlett-Packard Company (1999) 2. The PA 7100LC Microprocessor: A Case Study of IC Design Decisions in a Competitive EnvironmentLink 12 Mick Bass et al (April 1995: Hewlett-Packard Journal. Accessed May 2009) 3. Design methodologies for the PA 7100LC microprocessorLink 13 (.pdf) Mick Bass et al (April 1995: Hewlett-Packard Journal. Accessed May 2009)
The design goal of the 712 workstation was to reach performance levels of 1992-era workstations and servers (for instance HP 9000 735 workstation) at a fraction of their fabrication costs. Everything was kept simple, the case is one of the smallest Unix workstation cases, similar to the Sun SPARCstation 10 and 20 cases. 712s are very quiet, the fan of the power supply being almost not audible — the produced noise depends on the installed SCSI drive.
Introduced: early-1994 to mid-1995 (712/100) prices from $4,000 (712/60) and $8,820 (712/80) to $15,100 (712/100). Internals CPU
* 712/60: PA-7100LC 60MHz with 1KB on-chip L11 and 64KB off-chip L1 cache * 712/80: PA-7100LC 80MHz with 1KB on-chip L11 and 256KB off-chip L1 cache * 712/100: PA-7100LC 100MHz with 1KB on-chip L11 and 256KB off-chip L1 cache
1. The 1KB on-chip L1 cache is not really a true cache.
* LASI ASIC, which features: o NCR 53C710 8-bit single-ended SCSI-2 o Intel 82596CA 10Mb Ethernet controller o WD 16C522 compatible parallel o Harmony CD/DAT quality 16-bit stereo audio o NS 16550A compatible serial * Artist graphics, 8-bit * Intel 82503 Ethernet transceiver, media auto-selection * CS4215 or AD1849 programmable CODECs * WD37C65C Floppy controller * Two AM29F010 Flash EPROMs
» View a system-level ASCII-illustration of the chipset. Buses
* GSC system level I/O bus (128MB/s) * SCSI-2 single-ended bus
* 72-pin ECC SIMMs * Takes 8-32MB modules * Either 4 (on /60 and /80 models) or 6 (on /100) sockets * 16MB (2×8) minimum, 128MB (4×32)/ 192MB (6×32) maximum * Memory has to be installed in pairs, starting from slot 0, which is the closest slot to the drives.
* VRAM expansion slot for: o A2263-66520M - Video RAM expansion for higher resolutions/more colors * One slot for a GIO card (special formfactor GSC bus cards, only used in the 712), with the following cards available: o A2878A - second video o A4011A - 8025 Token Ring interface o A4011B - 8025 Token Ring interface o A4013A - second serial port o A4014A - second Ethernet LAN (AUI+TP) and serial port. Pinout for the AUI/RS232 Y-cable o A4015A - second serial & X25 link (DB9M RS232C connectors) o A4217A - second Ethernet LAN (AUI+TP) & second VGA o TAMS 50488 - HP-IB interface * One slot for a TSIO card (another special formfactor GSC card for the Teleshare expansion slot), with only one card offered: o A4012A - Teleshare POTS interface with two RJ11C jacks
* One tray for a 3.5″ Fast-Narrow SE 50-pin SCSI hard drive * One tray for a 3.5″ Floppy drive with special connector
* 50-pin HD SCSI-2 Fast-Narrow single-ended * DB9 male RS232C serial (up to 115200 baud) * DB25 female parallel * TP/RJ45 10Mbit Ethernet1 * 15-pin AUI 10Mbit Ethernet1 * HD15 VGA2 * Two PS/2 connectors for keyboard & mouse * Three phone jacks (microphone, headphones and line-in)
1. The system automatically detects the used port. 2. You can connect almost any monitor to the VGA jack. The 712 can drive VESA compatible multisync, HP fixed-frequency and many other popular FF monitors. It also is able to produce sync on green signals.
There is an firmware update available for the 712, which contains the latest version (2.3).
* PF_C7120023.txtLink 1 has details about the contents and installation of the patch. * PF_C7120023Link 2 contains the patch.
* Model 712 Technical ReferenceLink 3 (PDF, 3.7MB) * Model 712 Service HandbookLink 4 (PDF, 4.4MB)
* HP 9000 Model 712 OverviewLink 5 (PDF, HP Journal 4/95) * Design of the Model 712’s I/O subsystem (LASI)Link 6 (PDF, HP Journal 4/95) * Product design of the Model 712Link 7 (PDF, HP Journal 4/95) * In addition to the above almost the whole HP Journal April 1995 IssueLink 8 deals with the 712 workstation.
* NetBSD 712 serial console HOWTOLink 9, instructions to configure 712s to use serial console (i.e., run headless) * Pinout for the AUI/RS232 Y-cable for the optional second Ethernet/serial card.
* HP-UX: every 32-bit release from 10.01-11.11 works. o 10.20: runs very nice on all 712s. o 11.00 and 11i: 712s are not the best 11.x performers. Could be sluggish. * NeXTSTEP: version 3.3 works fine. * Linux: works fine. * OpenBSD: works fine. * NetBSD: experimental support as of 5/2005.
Benchmarks Model SPEC92, int SPEC92, fp SPEC95, int SPEC95, fp SPEC95 rate, int SPEC95 rate, fp 712/60 67.0 85.3 2.08 2.66 18.7 23.9 712/80 97.1 123.3 3.12 3.55 28.1 32.0 712/100 117.2 144.2 3.76 4.06 33.8 36.3
Compare these with other results on the Benchmarks page. Physical dimensions/Power
* 70×423×400 mm height/width/depth * 8.36kg net weight * 110W max. power input * 1.2A max. RMS at 240V * 2.7A max. RMS at 120V
Links on this page
1. Link 1: http://ftp.parisc-linux.org/kernels/712/PF_C7120023.txt 2. Link 2: http://ftp.parisc-linux.org/kernels/712/PF_C7120023 3. Link 3: http://h20000.www2.hp.com/bc/docs/support/SupportManual/lpv37629/lpv37629.pdf 4. Link 4: http://h20000.www2.hp.com/bc/docs/support/SupportManual/lpv37944/lpv37944.pdf 5. Link 5: http://www.hpl.hp.com/hpjournal/95apr/apr95a1.pdf 6. Link 6: http://www.hpl.hp.com/hpjournal/95apr/apr95a4.pdf 7. Link 7: http://www.hpl.hp.com/hpjournal/95apr/apr95a9.pdf 8. Link 8: http://www.hpl.hp.com/hpjournal/95apr/apr95.htm 9. Link 9: http://www.netbsd.org/Ports/hp700/serialconsole-hp-9000_712.html
Changing to Serial Console
To connect your PA-RISC machine to your PC so you can boot the system using a console, you need a 9 pin-to-9 pin female null-modem cable.
Unfortunately, HP decided that the 712 should be hard to configure for headless use. Improper setting of the console path may cause the system to become inoperable. Beware.
Briefly, you must get to the HP-UX bootloader prompt (which they call the ISL) which will allow you to permanently set your preferred console location to the first serial port at 9600 8N1.
The original source of this information is http://lists.parisc-linux.org/pipermail/parisc-linux/1999-December/008117.html.
To change to a serial console, you need:
- a PS/2 style keyboard
- a monitor with VGA style interface
- the HP-UX ISL (either an HP-UX bootable hard drive or netboot)
First, you need to get to the BootROM prompt. When your system prints the following on screen, press and hold ESC until you get the BOOT_ADMIN> prompt:
Press <ESCAPE> to stop boot sequence.
Setting monitor type
If your display doesn't show properly, the frequency may be out-of-range. You can select the monitor type suitable to your display.
If your 712 has the add-in VRAM board, normal VGA 680x480 mode is monitor type 7. Without the VRAM board, the number may be different (possibly 5?).
BOOT_ADMIN> monitor 7 Monitor Choices Type Resolution Frequency ---- ---------- --------- 1 1280x1024 72Hz 2 1024x768 75Hz 3 1024x768 70Hz 4 1024x768 75Hz Flat Panel 5 1280x1024 60Hz 6 1024x768 60Hz 7 640x480 60Hz 8 1280x1024 75Hz VESA 9 1024x768 75Hz VESA 10 800x600 75Hz VESA 11 640x480 75Hz VESA 12 1280x1024 72Hz Greyscale 13 1280x1024 50Hz Current Monitor Type is 7 640x480 60Hz BOOT_ADMIN> reset
If you have HP-UX installed on local disk
BOOT_ADMIN> boot pri isl Booting ISL Revision A.00.38 OCT 26, 1994 ISL>
Boot 712 from LAN
BOOT_ADMIN> boot lan isl
ISL Revision A.00.25 November 18, 1992
Run the following command to set your 712 to use a serial RS-232 console with 9600 Baud, 8 data bits, 1 stop bit, and no parity:
ISL> conspath 2/0/4.0x283
To set your 712 to use the local console (i.e. keyboard and screen), run the following command:
ISL> conspath 1/0/0.0
You can use the display and information commands to verify that your settings have been stored properly. Once you're sure everything looks right, power cycle your workstation to start using your serial console.
Additionally, you can temporarily use the local console by pressing the “Esc” key on the PS/2 keyboard while resetting. This is setting only affects the console location temporarily and only works with firmware rev 1.6 and later.
---------------------------------------------------------------------------- BootRom Version 1.6 Memory Size: 192 MB ---------------------------------------------------------------------------- (c) Copyright 1990-1993, Hewlett-Packard Company. All rights reserved Press <ESCAPE> to stop boot sequence. <ESC> Selecting a system to boot. ---------------------------------------------------------------------------- Command Description ------- ----------- Auto [boot|search] [on|off] Display or set auto flag Boot [pri|alt|scsi.addr] [isl] Boot from primary, alternate or SCSI Boot lan[.lan_addr] [install] [isl] Boot from LAN Chassis [on|off] Enable chassis codes Diagnostic [on|off] Enable/disable diagnostic boot mode Fastboot [on|off] Display or set fast boot flag Help Display the command menu Information Display system information LanAddress Display LAN station addresses Monitor [type] Select monitor type Path [pri|alt] [lan.id|SCSI.addr] Change boot path Pim [hpmc|toc|lpmc] Display PIM info Search [ipl] [scsi|lan [install]] Display potential boot devices Secure [on|off] Display or set security mode ---------------------------------------------------------------------------- BOOT_ADMIN> boot lan isl Booting ISL Revision A.00.25 November 18, 1992 ISL> display Fastsize value is 0000000F Autoboot is ON (enabled) Autosearch is ON (enabled) Primary boot path is 2/0/22.214.171.124.0.0.0 Primary boot path is (hex) 2/0/126.96.36.199.0.0.0 Alternate boot path is 2/0/188.8.131.52.0.0.0 Alternate boot path is (hex) 2/0/184.108.40.206.0.0.0 System console path is 220.127.116.11.0.0.0 System console path is (hex) 18.104.22.168.0.0.0 ISL> conspath 2/0/4.0x283 ISL> display Fastsize value is 0000000F Autoboot is ON (enabled) Autosearch is ON (enabled) Primary boot path is 2/0/22.214.171.124.0.0.0 Primary boot path is (hex) 2/0/126.96.36.199.0.0.0 Alternate boot path is 2/0/188.8.131.52.0.0.0 Alternate boot path is (hex) 2/0/184.108.40.206.0.0.0 System console path is 2/0/4.6220.127.116.11.0.0 System console path is (hex) 2/0/4.218.104.22.168.0.0 ISL>
gram form the original message
Matthew Wilcox writes...
>On Thu, Dec 23, 1999 at 07:45:00AM -0800, Bill Katz William" wrote: >> |How do I set the console on my 712 to be the serial port, not the
>> |display? >> | >> |Thanks >> | >> >> Boot to ISL and use the conspath >> command to change the console back to rs232. The command to use is: >> >> serial >> conspath 2/0/4.643 >> graphics >> conspath 1/0/0.0 > >This contradicts the PA-RISC Booting HOWTO: > >----- > >22.214.171.124.3. How can I change the boot console to serial on a 712? > >Unfortunately, you can't. Although 712s are configured for in-house HP >development to use serial console, this configuration isn't supported >in the field. You have to use a graphics console for 712s. > >----- > >I'd like to know if this needs to be corrected.
The above statement about serial console not being "supported" on 712 is correct. That doesn't mean you can't do it. Here are the instructions,
CONFIGURING A RS-232 CONSOLE on a 712
An RS-232 console is not a supported feature in the 712 products. For this reason users cannot select the RS-232 port as a console from the BOOT_ADMIN prompt.
These instructions will configure an RS-232 console with 9600 Baud, 8 data bits, 1 stop bit, and no parity.
NOTE: If the following instructions are not entered correctly, your system may be left in an un-usable state. Contact support to "dagger" your system in this case.
Power up the 712 system. Press (ESCAPE) during boot to abort auto booting the system. At the BOOT_ADMIN> prompt, use the boot command and the isl keyword. This will stop the boot sequence at ISL instead of booting to the
For example: 'boot scsi.6 isl' At the ISL> prompt, type 'conspath 2/0/4.0x283' At the ISL> prompt, type 'disp' and verify console path is: (hex) 2/0/4.2126.96.36.199.0.0 If necessary re-type the conspath command above. Connect an RS-232 terminal to the system. Power cycle the system to bring it up on an RS-232 console.
As it indicates above, *BE VERY CAREFUL* or you can hose your system. If you do, I have one of the "dagger" cards that can be loaned out to fix it.
-- Matt Taggart firstname.lastname@example.org
X-From-Line: email@example.com Thu Mar 11 15:54:36 1999 Return-Path: <firstname.lastname@example.org> Received: from merlin.pcj.primenet.com (email@example.com [192.168.111.10]) by merlin.pcj.primenet.com (8.8.7/8.8.7) with ESMTP id PAA14261 for <firstname.lastname@example.org>; Thu, 11 Mar 1999 15:54:32 -0800 Resent-From: email@example.com Received: from pop.primenet.com by merlin.pcj.primenet.com (fetchmail-4.4.7 POP3) for <pcj/merlin.pcj.primenet.com> (single-drop); Thu, 11 Mar 1999 15:54:36 PST Received: from smtp01.primenet.com (firstname.lastname@example.org [188.8.131.52]) by primenet.com (8.8.8/8.8.5) with ESMTP id PAA14177 for <email@example.com>; Thu, 11 Mar 1999 15:32:44 -0700 (MST) Received: (from daemon@localhost) by smtp01.primenet.com (8.8.8/8.8.8) id PAA26870 for <firstname.lastname@example.org>; Thu, 11 Mar 1999 15:32:42 -0700 (MST) Received: from SOD.RES.CMU.EDU(184.108.40.206)
via SMTP by smtp01.primenet.com, id smtpd026771; Thu Mar 11 15:32:32 1999
Received: (from listserv@localhost) by sod.res.cmu.edu (8.8.7/8.8.7) id RAA06933; Thu, 11 Mar 1999 17:32:02 -0500 Resent-Date: Thu, 11 Mar 1999 17:32:02 -0500 X-Authentication-Warning: sod.res.cmu.edu: listserv set sender to email@example.com using -f Delivered-To: firstname.lastname@example.org Date: Thu, 11 Mar 1999 16:35:15 -0600 From: Jason Eckhardt <email@example.com> Message-Id: <199903112235.QAA05851@equator.com> To: firstname.lastname@example.org Subject: [hppa-linux] Boot #4 and source on ftp site Resent-Message-ID: <"3RIsy2.0.Ei1.XH4ws"@sod.res.cmu.edu> Reply-To: email@example.com X-Mailing-List: <firstname.lastname@example.org> archive/latest/171 X-Loop: email@example.com Precedence: list Resent-Sender: firstname.lastname@example.org X-UIDL: 9ce996d3976fbc9addd3c92c1b564e49 Lines: 25 Xref: merlin.pcj.primenet.com palinux:142
Boot test #4: This is essentially the same code as #3 but I have taken out some delays, modified the cache flush routines, and turned verbose (debug) mode back on. I want to make sure that not having the delays makes no difference and that no characters get dropped when there is a lot of text (as in debug mode). Please let me know if the test still passes as before. Hopefully this will be the last test for a while. Kernel work comes next.
I have uploaded the binary as well as a new source drop to the ftp site. The source is now GPL'd and a detailed README is included which gives an overview of the boot code operation. This source supersedes any previous source you may have laying around.
ftp from sod.res.cmu.edu:/pub/parisc/hilo
boot_rel_0.2.tar.gz The latest source code and documentation. bootstrap_4.bin.gz Bootstrap binary #4.
Y cable pinouy
Pinout for RS232/AUI cable(A2263-62045) for 712 card (A2263-66536)
There is a card for the 712(HP part #A2263-66536) that provides 2nd AUI lan and 2nd DB9 RS232 port. The back of the card has a 26 pin connector and the 15pin AUI and 9pin RS232 connectors are provided by a special Y cable (A2263-62045) which are pretty hard to find. Here is the pinout of this cable in case you need to make one.
These diagrams are looking at the end of the connector not the back. Make sure to take that into account if building a cable. Pin numbering is taken from the numbers on the plastic in the cable. If a pin is not connected it is represented as an "o". The numbers outside the bottom connectors are the pin numbers that that pin is connected to on the top connector.
--------------------------------- \ o o 3 o o o 7 8 9 / \ 10 11 12 13 o o 16 17 18 / \ 19 20 21 22 o 24 25 26 / ------------------------- 12 13 20 19 18 9 8 7 24 --------------------------- ----------------- AUI \ o o 6 5 o 3 2 o / \ 1 2 3 4 5 / RS232 \ o 10 11 12 o 14 15 / \ 6 7 8 9 / --------------------- ------------ 22 21 3 11 10 26 25 17 16