Jetson/General debug

From eLinux.org
< Jetson
Revision as of 00:36, 11 January 2021 by Waynewww (talk | contribs)
Jump to: navigation, search

Currently this page is applicable to release <= rel-32.4.4.

Get prepared

This section is to share some debug tips for users to understand the basic flow of how to use/debug jetson platform.
Before we start to describe each kind of error, you should check below pages to understand how to dump a serial log from UART. Please note that only UART console can dump the bootloader logs. If your board hangs in somewhere prior to the kernel, then you must dump the log from UART.

Tutorials:
 https://www.jetsonhacks.com/2017/03/24/serial-console-nvidia-jetson-tx2/ 
 https://www.jetsonhacks.com/2019/04/19/jetson-nano-serial-console/
 https://developer.ridgerun.com/wiki/index.php?title=Xavier/In_Board/Getting_in_Board/Serial_Console

Also, we put all the official document in the dlc here:

https://developer.nvidia.com/embedded/downloads


And if you want some help or report issue, please file a topic on forum.

https://forums.developer.nvidia.com/

When reporting issue, you may tell your problem with below details.

1. The software release version you are using (e.g. which jetpack).
2. Is this issue reproducible on devkit or custom board?
3. How to reproduce this issue? It would be good if a sample code is attached.
4. What peripherals are connected on device?

Flash problem

SDKM

SDKManager is a GUI tool to replace old Jetpack. This tool has two basic functions: flash the board(driver package/BSP) and install the SDK(cuda/tensorRT..etc.).
https://developer.nvidia.com/nvidia-sdk-manager
To run sdkm, you have to prepare a x86 host with ubuntu 16.04 or 18.04. Some users asked whehter it supports ARM version so that they can flash jetson by another ARM device.
Currently, it is not supported.
Flash and install SDK could be separate. It means you could flash the board and skip the installation of SDK and vice versa.

  • How to debug if flashing process is stuck in sdkm?

In general, the flash process would finish in 10 minutes. If it lasts longer than this, the flash process probably has problem. To debug flash, I would suggest to use flash.sh directly instead of SDKM GUI tool.

flash.sh
 This is a official tool to flash jetson platform. This tool is also installed and used by SDKM. 
After you choose the flash button in sdkm, it would download a package "Linux_for_Tegra" on your host.   The flash.sh is inside this folder.
For more detail about how to use flash.sh, please refer to Jetson quick start guide -> https://developer.nvidia.com/embedded/downloads
  • What log should I prepare for flash problem?

To debug flash problem. You need two parts of log for forum admin to check.

1. The result of flash.sh  
 This log should be seen after you run above flash.sh
2. The result from device 
 During the flash, the host would send some binary to target device and use this binary to flash. It is a protocol over usb. To dump this log, you need to enable serial console on UART as above tutorial (methods in the top section)
You shall see the log start to dump in the meantime when flash.sh starts to flash your board.
  • The installation of SDK is stuck, why?
The SDK installation could be done through ethernet/wifi or usb device mode. You could just ping or ssh before sdk installation starts.
USB device mode is a virtual internet interface created when you connect micro usb cable to jetson.  It would use a IP 192.168.55.x as device IP and create another 192.168.55.100 on your host.
However, this method requires your host to have driver support.  Some users' host may not support it.  In this case, please use wired ethernet to install.  

Boot

After your flash process finishes, the system would boot up no matter you install sdk or not.

  • My system gets hang and doesn't respond. How to resolve?
There are lots of reason that might cause system hang.  Here are some common cases.
1. Need to configure user account
 This is a new feature after rel-32.1.  User needs to configure their own ubuntu account with USB keyboard and HDMI monitor.
If you don't have HDMI monitor for it, there is also alternative method- oem config to help.  You could refer the detail in L4T dev guide: https://docs.nvidia.com/jetson/l4t/index.html
2. There is bootloader failure or kernel failure
 To dump the log, you need to enable the serial console on UART.  This is the only way to debug bootloader log.
 For kernel log, before dumping it, you need to make sure there is no "quiet" in kernel cmdline. If you see this, it would disable the boot log.
 The way to remove this keyword is check the extlinux.conf under "Linux_for_Tegra/rootfs/boot/extlinux"on your host.  If you don't know how to tell whether it is in kernel cmdline. Just see the length of your kernel log.  The full log should have usb/pcie init log which are available on all kinds of jetson platforms.  If you don't see them, then your log is in silent mode.

  • I see some logs are printed on the screen and there is no desktop for me to operate
Such issue is somehow very common on forum and the root cause may differ case by case. For example, such error may happen even when running out of disk space.
When such case happens, enable the uart console and make sure your board is still booting up.  Try to backup the system under such case and file the topic for forum moderator.

Board name

Some users may get confused by the board ID within Jetpack. Here is the list to check.

 P2180  -> Jetson TX1
 P3310  -> Jetson TX2
 P3489  -> Jetson TX2i
 P3448  -> Jetson Nano devkit
 P3448-0020 -> Jetson Nano production module
 P2888 -> Jetson Xavier
 P2888-0060 -> Jetson Xavier-8GB

When you run "sudo ./flash.sh <BoardID> mmcblk0p1" command to flash your board. It is actually searching the config file <boardID>.conf under Linux_for_Tegra.
For example,

sudo ./flash.sh jetson-tx2i mmcblk0p1 

This one would try to check the file in jetson-tx2i.conf. It means you could also create your own board name and it would work if the format in this config file is correct.

Device tree debug tips

1. There are lots of dtb file in source. Which one should I modify?
Ans: If you already flashed your board and it can boot up, please try "dmesg |grep dts". This will tell the name of dts.

nvidia@nvidia-desktop:~$ dmesg |grep dts
DTS File Name: /dvs/git/dirty/git-master_linux/kernel/kernel-4.9/arch/arm64/boot/dts/../../../../../../hardware/nvidia/platform/t210/porg/kernel-dts/tegra210-p3448-0000-p3449-0000-b00.dts

2. How to check if my change/patch take effect in dts?
Ans: You can check each property under /proc/device-tree/. For example, if you want to check the status of i2c@7000c000, then

nvidia@nvidia-desktop:/proc/device-tree$ xxd i2c@7000c000/status 
00000000: 6f6b 6179 00                             okay.