Difference between revisions of "Microsemi:VSC8531BB1G/getting-started"

From eLinux.org
Jump to: navigation, search
(Created page with " Step 1: Plug in your VSC8531BBB +5V DC / 1A+ power supply Step2: Plug in your VSC8531BBB via supplied micro USB cable Step 3: Install drivers Step 4: Browse to web server...")
 
 
(20 intermediate revisions by the same user not shown)
Line 1: Line 1:
 +
[[File:Microsemi-Logo-Email-Size.png|frameless|left|Microsemi Logo|link=www.microsemi.com]]
  
Step 1:
+
===Getting Started with your Microsemi VSC8531BB1G - BeagleBone Black 1G - Development Board===
Plug in your VSC8531BBB +5V DC / 1A+ power supply
+
<br />
  
Step2:
+
[[File:BeagleBoneBlack_Photo_2016_05_13.png]]
Plug in your VSC8531BBB via supplied micro USB cable
 
  
Step 3:
 
Install drivers
 
  
Step 4:
+
'''Step 1:''' Plug in your Microsemi VSC8531BB1G (BeagleBone Black 1G) Development Board to a recommended +5V DC / 2A (or higher) power supply.
Browse to web server on the VSC8531BBB (using Chrome or Firefox)
+
Note: The VSC8531BB1G can NOT be powered from USB due to the PMIC (power management IC) limiting the max current to 500mA. See below for description of a possible power supply.
  
Getting Started with the VSC8531BBB
 
  
The VSC8531BBB (based on Rev C of the BeagleBone Black) is a tiny computer with all the capability of today’s desktop machines, without the bulk, expense, or noise. Please read the step-by-step getting started tutorial below to begin developing with your VSC8531BBB in minutes.
+
'''Step 2:''' Plug in your Microsemi VSC8531BB1G via supplied micro USB cable
 +
Note: The VSC8531BB1G can NOT be powered from USB due to the PMIC (power management IC) limiting the max current to 500mA. If you accidentally did this step first, please unplug the USB cable and go to Step 1.
  
For additional getting started information, please visit the following support wiki page:
 
  
[[link=Microsemi:VSC8531BBB/Specifications_and_Resources]]
+
'''Step 3:''' Install drivers
  
Plug in your VSC8531BBB +5V DC / 1A+ power supply.
 
  
Specific recommendations
+
'''Step 4:''' Browse to web server on the Microsemi VSC8531BB1G (using your favorite browser, like Chrome or Firefox)
5V power supplies
+
Note: Internet Explorer will NOT work
The power adapter needs to provide 5V over a 5.5mm outer diameter and 2.1mm inner diameter barrel connector. A barrel connector length of 9.5mm is more than sufficient. The currently recommended supply current is at least 1.2A (or 6W), but at least 2A (or 10W) is recommended if you are going to connect up anything over the USB. The actual power consumption will vary greatly with changes on the USB load. Below are some recommended units:
 
  
Digi-Key-supplied PHIHONG USA PSC12R-050 - Be sure to get the right adapter for your country
 
I also recommend searching for power adapters on delicious.com and personally tagging any that you find useful, either already on that list or not already on that list.
 
Plug in your Beagle via USB
 
Use the provided USB cable to plug your Beagle into your computer. This will both power the board and provide a development interface. BeagleBone Black will boot Linux from the on-board 2GB or 4GB eMMC. Either BeagleBone Black or original BeagleBone may also boot from a microSD card. Original BeagleBone is provided with a pre-configured 4GB microSD card.
 
  
BeagleBone or BeagleBone Black will operate as a flash drive providing you with a local copy of the documentation and drivers. Note that this interface may not be used to re-configure the microSD card with a new image, but may be used to update the boot parameters using the uEnv.txt file.
+
 
 +
'''Getting Started with the Microsemi VSC8531BB1G Development Board'''
 +
 
 +
The Microsemi VSC8531BB1G (based on Rev C of the BeagleBone Black open-source HW design files) is a tiny computer with all the capability of today’s desktop machines, without the bulk, expense, or noise. Please read the step-by-step getting started tutorial below to begin developing with your VSC8531BB1G in minutes.
 +
 
 +
For additional VSC8531BB1G details , please visit the following support wiki page: '''[[Microsemi:VSC8531BB1G/Specifications and Resources|VSC8531BB1G Specifications & Resources]]'''
 +
 
 +
 
 +
'''Plug in your VSC8531BB1G +5V DC / 2A (or higher) power supply.'''
 +
 
 +
Note: The power adapter needs to provide 5V over a 5.5mm outer diameter and 2.1mm inner diameter barrel connector. A barrel connector length of 9.5mm is more than sufficient.
 +
The currently recommended supply current is at least 1.2A (or 6W), but at least 2A (or 10W) is recommended if you are going to connect up anything over the USB Type A port.
 +
The actual power consumption of the VSC8531BB1G will vary greatly with changes on the USB load as well as any BeagleBoard compatible "Cape Boards" that may also be connected to the VSC8531BB1G.
 +
One such recommended power supply is the: '''[http://www.digikey.com/product-detail/en/phihong-usa/PSC12R-050/993-1050-ND/2384498 PHIHONG USA PSC12R-050 - Please be sure to get the right adapter for your country!]'''
 +
 
 +
 
 +
'''Plug in your VSC8531BB1G via micro USB'''
 +
 
 +
Use the provided micro USB cable to plug your VSC8531BB1G into your computer. This will provide a development interface. The VSC8531BB1G will boot the default Debian Linux image from the on-board 4GB eMMC. Alternatively, the VSC8531BB1G may also boot from a microSD card.
 +
 
 +
The VSC8531BB1G will operate as a USB flash drive providing you with a local copy of the latest available documentation and drivers (at the time the unit was assembled) when booting from the 4GB eMMC. Note that this interface may not be used to re-configure the microSD card with a new image, but may be used to update the boot parameters using the uEnv.txt file.
  
 
You'll see the PWR LED lit steadily. Within 10 seconds, you should see the other LEDs blinking in their default configurations.
 
You'll see the PWR LED lit steadily. Within 10 seconds, you should see the other LEDs blinking in their default configurations.
  
USR0 is configured at boot to blink in a heartbeat pattern
+
USR0 is configured at boot to blink in a heartbeat pattern
USR1 is configured at boot to light during microSD card accesses
+
USR1 is configured at boot to light during microSD card accesses
USR2 is configured at boot to light during CPU activity
+
USR2 is configured at boot to light during CPU activity
USR3 is configured at boot to light during eMMC accesses
+
USR3 is configured at boot to light during eMMC accesses
  
  
Install drivers
+
'''Install drivers'''
Install the drivers for your operating system to give you network-over-USB access to your Beagle. Additional drivers give you serial access to your board.
 
  
Operating System USB Drivers Comments
+
Install the drivers for your operating system to give you network-over-USB access to your VSC8531BB1G. Additional drivers are available to give you serial access to your board.
Windows (64-bit) 64-bit installer
 
If in doubt, try the 64-bit installer first.
 
  
 +
 +
{| class="wikitable"
 +
|-
 +
! Operating System !! USB Drivers !! Comments
 +
|-
 +
| Windows (64-bit) || 64-bit installer || If in doubt, try the 64-bit installer first.
 
Note #1: Windows Driver Certification warning may pop up two or three times. Click "Ignore", "Install" or "Run"
 
Note #1: Windows Driver Certification warning may pop up two or three times. Click "Ignore", "Install" or "Run"
 +
 
Note #2: To check if you're running 32 or 64-bit Windows see this: https://support.microsoft.com/kb/827218.
 
Note #2: To check if you're running 32 or 64-bit Windows see this: https://support.microsoft.com/kb/827218.
 +
 
Note #3: On systems without the latest service release, you may get an error (0xc000007b). In that case, please install the following and retry: https://www.microsoft.com/en-us/download/confirmation.aspx?id=13523.
 
Note #3: On systems without the latest service release, you may get an error (0xc000007b). In that case, please install the following and retry: https://www.microsoft.com/en-us/download/confirmation.aspx?id=13523.
 +
 
Note #4: You may need to reboot Windows.
 
Note #4: You may need to reboot Windows.
 +
 
Note #5: These drivers have been tested to work up to Windows 10
 
Note #5: These drivers have been tested to work up to Windows 10
Windows (32-bit) 32-bit installer
+
|-
Mac OS X Network
+
| Windows (32-bit) || 32-bit installer || See above
Serial
+
|-
Install both sets of drivers.
+
| Mac OS X || Network Serial || Install both sets of drivers.
Linux mkudevrule.sh Driver installation isn't required, but you might find a few udev rules helpful.
+
|-
Note: Additional FTDI USB to serial/JTAG information and drivers are available from https://www.ftdichip.com/Drivers/VCP.htm.
+
| Linux || mkudevrule.sh || Driver installation isn't required, but you might find a few udev rules helpful.
 +
|}
 +
 +
'''Note:''' Additional FTDI USB to serial/JTAG information and drivers are available from https://www.ftdichip.com/Drivers/VCP.htm.
 +
 
 +
'''Note:''' Additional USB to virtual Ethernet information and drivers are available from https://www.linux-usb.org/gadget/ and https://joshuawise.com/horndis.
 +
 
 +
'''Browse to your VSC8531BB1G'''
  
Note: Additional USB to virtual Ethernet information and drivers are available from https://www.linux-usb.org/gadget/ and https://joshuawise.com/horndis.
+
Using either Chrome or Firefox browsers (Internet Explorer will NOT work), browse to the web server running on your board. It will load a presentation showing you the capabilities of the board. Use the arrow keys on your keyboard to navigate the presentation.
  
Browse to your Beagle
+
Click here to launch the Web Page running on the Web Server on your VSC8531BB1G: [http://192.168.7.2 http://192.168.7.2]
Using either Chrome or Firefox (Internet Explorer will NOT work), browse to the web server running on your board. It will load a presentation showing you the capabilities of the board. Use the arrow keys on your keyboard to navigate the presentation.
 
  
Click here to launch: http://192.168.7.2
+
'''Troubleshooting'''
Older software images require you to EJECT the BEAGLE_BONE drive to start the network. With the latest software image, that step is no longer required.
 
  
Troubleshooting
 
 
Do not use Internet Explorer.
 
Do not use Internet Explorer.
 
One option to browse your board is to use this node-webkit based application (currently limited to Windows machines): beaglebone-getting-started.zip.
 
  
 
Virtual machines are not recommended when using the direct USB connection. It is recommended you use only network connections to your board if you are using a virtual machine.
 
Virtual machines are not recommended when using the direct USB connection. It is recommended you use only network connections to your board if you are using a virtual machine.
Line 77: Line 97:
 
When using 'ssh' with the provided image, the username is 'root' and the password is blank.
 
When using 'ssh' with the provided image, the username is 'root' and the password is blank.
  
Visit beagleboard.org/support for additional debugging tips.
+
Please visit beagleboard.org/support for additional debugging tips.
 +
 
 +
'''Update board with latest software'''
 +
 
 +
'''Step #1:''' Download the latest software image
  
Update board with latest software
 
Step #1: Download the latest software image
 
 
Download the desired image from https://beagleboard.org/latest-images.
 
Download the desired image from https://beagleboard.org/latest-images.
  
 
Note: Due to sizing necessities, this download may take 30 minutes or more.
 
Note: Due to sizing necessities, this download may take 30 minutes or more.
  
The file you download will have an .img.xz extention. This is a compressed sector-by-sector image of the SD card.
+
The file you download will have an .img.xz extention. This is a compressed sector-by-sector image of the SD card, so it is substantial in size.
  
  
Step #2: Install compression utility
+
'''Step #2:''' Install the 7-zip compression utility
Download and install 7-zip.
+
Download and install 7-zip from [http://www.7-zip.org/download.html|http://www.7-zip.org/download.html]
  
  
 +
'''Step #3:''' Decompress the image
 +
Use 7-zip to decompress the SD card .img file
  
Step #3: Decompress the image
 
Use 7-zip to decompress the SD card .img file
 
  
 +
'''Step #4:''' Install SD card programming utility
 +
Download and install Win32DiskImager for Windows from the Ubuntu Wiki page. Be sure to download the binary distribution.
  
Step #4: Install SD card programming utility
+
https://wiki.ubuntu.com/Win32DiskImager
Download and install Image Writer for Windows. Be sure to download the binary distribution.
 
  
 +
Some general help on programming microSD / SD cards can be found on the Win32DiskImager page below.
  
 +
https://wiki.ubuntu.com/Win32DiskImager/iso2usb
  
Some general help on programming SD cards can be found on the Ubuntu Image Writer page.
+
'''Step #5:''' Connect SD card to your computer
 +
Use a microSD card to SD adapter or a USB adapter to connect the SD card to your computer.
  
Step #5: Connect SD card to your computer
 
Use the provided microSD card to SD adapter or a USB adapter to connect the SD card to your computer.
 
  
Step #6: Write the image to your SD card
+
'''Step #6:''' Write the image to your SD card
Use either the Ubuntu Image Writer or instructions on its page to write the decompressed image to your SD card.
+
Use the instructions on the  page to write the decompressed image to your SD card.
  
Note: You may see a warning about damaging your device. This is fine to accept as long as you are pointing to your SD card for writing.
+
Note: You may see a warning about damaging your device. This is fine to accept as long as you are pointing to your SD card for writing.
  
Note: You should not have your BeagleBone connected to your computer at this time.
+
Note: You should '''NOT''' have your VSC8531BB1G connected to your computer at this time.
  
 
   
 
   
Step #7: Eject the SD card
+
'''Step #7:''' Eject the SD card
 
Eject the newly programmed SD card.
 
Eject the newly programmed SD card.
  
Step #8: Boot your board off of the SD card
 
Insert SD card into your (powered-down) board, hold down the USER/BOOT button (if using Black) and apply power, either by the USB cable or 5V adapter.
 
  
If using an original BeagleBone, you are done.
+
'''Step #8:''' Boot your board off of the SD card
 +
Insert SD card into your (powered-down) board, hold down the USER/BOOT button and apply power using the +5V DC adapter.
  
If using BeagleBone Black and desire to write the image to your on-board eMMC, you'll need to follow the instructions at http://elinux.org/Beagleboard:BeagleBoneBlack_Debian#Flashing_eMMC. When the flashing is complete, all 4 USRx LEDs will be steady on or off. The latest Debian flasher images automatically power down the board upon completion. This can take up to 45 minutes. Power-down your board, remove the SD card and apply power again to be complete.
+
If you desire to write the image to your on-board eMMC, you'll need to follow the instructions at http://elinux.org/Beagleboard:BeagleBoneBlack_Debian#Flashing_eMMC. When the flashing is complete, all 4 USRx LEDs will be steady on or off. The latest Debian flasher images automatically powers down the board upon completion. This can take up to 45 minutes so please be patient. Again, ensure that all LED activity has stopped before attempting to power-down your board - if this doesn't happen automatically - by removing the power adapter cable, remove the SD card and then plug in the power adapter cable to complete the process.
  
 
Other currently available software images
 
Other currently available software images
 
Some of the starting images below involve multiple steps to produce an SD card image or otherwise change some of the steps above, so be sure to read all the instructions on their pages. Choose the starting point you want, download or produce the SD card image and follow the steps above.
 
Some of the starting images below involve multiple steps to produce an SD card image or otherwise change some of the steps above, so be sure to read all the instructions on their pages. Choose the starting point you want, download or produce the SD card image and follow the steps above.
 +
 +
'''Supported Distributions'''
  
 
At the time of release, not all of these distributions support BeagleBone Black, but should soon.
 
At the time of release, not all of these distributions support BeagleBone Black, but should soon.
Line 133: Line 158:
 
Linux: Debian, Angstrom Distribution, Ubuntu, ArchLinux, Gentoo, Sabayon, Buildroot, Erlang, Fedora
 
Linux: Debian, Angstrom Distribution, Ubuntu, ArchLinux, Gentoo, Sabayon, Buildroot, Erlang, Fedora
 
Other: QNX, FreeBSD
 
Other: QNX, FreeBSD
Projects page
 
Hardware documentation
 
The BeagleBoneBlack wiki page documents all of the known hardware issues, as well as the latest available software, hardware hardware documentation and design materials.
 
  
Time to read that manual and check out the design materials: BeagleBone Black Docs.
+
'''Creative Commons Attribute-ShareAlike 3.0 Unported License'''
  
Links to design materials for various releases can be found at beagleboard.org/hardware/design.
+
This work is licensed under the Creative Commons Attribution-Share Alike 3.0 Unported License. To
 +
view a copy of this license, visit creativecommons.org or send a letter to:
 +
 +
Creative Commons
 +
171 Second Street, Suite 300
 +
San Francisco, California, 94105, USA.
  
Books
+
This page is a derivative work of http://www.elinux.org/Beagleboard:BeagleBoneBlack
For a complete list of books on BeagleBone, see http://beagleboard.org/books.
+
and is attributed to the work originally created by Gerald Coley of BeagleBoard.org.
 
+
+
For more information, see Creative Commons Attribution-ShareAlike 3.0 Unported License
Bad to the Bone
 
Perfect for high-school seniors or freshman univerisity level text, consider using "Bad to the Bone"
 
 
 
BeagleBone Cookbook
 
A lighter treatment suitable for a bit broader audience without the backgrounders on programming and electronics, consider "BeagleBone Cookbook"
 
 
 
Exploring BeagleBone and Embedded Linux Primer
 
To take things to the next level of detail, consider "Exploring BeagleBone" which can be considered the missing software manual and utilize "Embedded Linux Primer" as a companion textbook to provide a strong base on embedded Linux suitable for working with any hardware that will run Linux.
 

Latest revision as of 14:24, 8 September 2016

Microsemi Logo

Getting Started with your Microsemi VSC8531BB1G - BeagleBone Black 1G - Development Board


BeagleBoneBlack Photo 2016 05 13.png


Step 1: Plug in your Microsemi VSC8531BB1G (BeagleBone Black 1G) Development Board to a recommended +5V DC / 2A (or higher) power supply.

Note: The VSC8531BB1G can NOT be powered from USB due to the PMIC (power management IC) limiting the max current to 500mA. See below for description of a possible power supply.


Step 2: Plug in your Microsemi VSC8531BB1G via supplied micro USB cable

Note: The VSC8531BB1G can NOT be powered from USB due to the PMIC (power management IC) limiting the max current to 500mA. If you accidentally did this step first, please unplug the USB cable and go to Step 1.


Step 3: Install drivers


Step 4: Browse to web server on the Microsemi VSC8531BB1G (using your favorite browser, like Chrome or Firefox)

Note: Internet Explorer will NOT work


Getting Started with the Microsemi VSC8531BB1G Development Board

The Microsemi VSC8531BB1G (based on Rev C of the BeagleBone Black open-source HW design files) is a tiny computer with all the capability of today’s desktop machines, without the bulk, expense, or noise. Please read the step-by-step getting started tutorial below to begin developing with your VSC8531BB1G in minutes.

For additional VSC8531BB1G details , please visit the following support wiki page: VSC8531BB1G Specifications & Resources


Plug in your VSC8531BB1G +5V DC / 2A (or higher) power supply.

Note: The power adapter needs to provide 5V over a 5.5mm outer diameter and 2.1mm inner diameter barrel connector. A barrel connector length of 9.5mm is more than sufficient.
The currently recommended supply current is at least 1.2A (or 6W), but at least 2A (or 10W) is recommended if you are going to connect up anything over the USB Type A port.
The actual power consumption of the VSC8531BB1G will vary greatly with changes on the USB load as well as any BeagleBoard compatible "Cape Boards" that may also be connected to the VSC8531BB1G.
One such recommended power supply is the: PHIHONG USA PSC12R-050 - Please be sure to get the right adapter for your country!


Plug in your VSC8531BB1G via micro USB

Use the provided micro USB cable to plug your VSC8531BB1G into your computer. This will provide a development interface. The VSC8531BB1G will boot the default Debian Linux image from the on-board 4GB eMMC. Alternatively, the VSC8531BB1G may also boot from a microSD card.

The VSC8531BB1G will operate as a USB flash drive providing you with a local copy of the latest available documentation and drivers (at the time the unit was assembled) when booting from the 4GB eMMC. Note that this interface may not be used to re-configure the microSD card with a new image, but may be used to update the boot parameters using the uEnv.txt file.

You'll see the PWR LED lit steadily. Within 10 seconds, you should see the other LEDs blinking in their default configurations.

USR0 is configured at boot to blink in a heartbeat pattern
USR1 is configured at boot to light during microSD card accesses
USR2 is configured at boot to light during CPU activity
USR3 is configured at boot to light during eMMC accesses


Install drivers

Install the drivers for your operating system to give you network-over-USB access to your VSC8531BB1G. Additional drivers are available to give you serial access to your board.


Operating System USB Drivers Comments
Windows (64-bit) 64-bit installer If in doubt, try the 64-bit installer first.

Note #1: Windows Driver Certification warning may pop up two or three times. Click "Ignore", "Install" or "Run"

Note #2: To check if you're running 32 or 64-bit Windows see this: https://support.microsoft.com/kb/827218.

Note #3: On systems without the latest service release, you may get an error (0xc000007b). In that case, please install the following and retry: https://www.microsoft.com/en-us/download/confirmation.aspx?id=13523.

Note #4: You may need to reboot Windows.

Note #5: These drivers have been tested to work up to Windows 10

Windows (32-bit) 32-bit installer See above
Mac OS X Network Serial Install both sets of drivers.
Linux mkudevrule.sh Driver installation isn't required, but you might find a few udev rules helpful.

Note: Additional FTDI USB to serial/JTAG information and drivers are available from https://www.ftdichip.com/Drivers/VCP.htm.

Note: Additional USB to virtual Ethernet information and drivers are available from https://www.linux-usb.org/gadget/ and https://joshuawise.com/horndis.

Browse to your VSC8531BB1G

Using either Chrome or Firefox browsers (Internet Explorer will NOT work), browse to the web server running on your board. It will load a presentation showing you the capabilities of the board. Use the arrow keys on your keyboard to navigate the presentation.

Click here to launch the Web Page running on the Web Server on your VSC8531BB1G: http://192.168.7.2

Troubleshooting

Do not use Internet Explorer.

Virtual machines are not recommended when using the direct USB connection. It is recommended you use only network connections to your board if you are using a virtual machine.

When using 'ssh' with the provided image, the username is 'root' and the password is blank.

Please visit beagleboard.org/support for additional debugging tips.

Update board with latest software

Step #1: Download the latest software image

Download the desired image from https://beagleboard.org/latest-images.

Note: Due to sizing necessities, this download may take 30 minutes or more.

The file you download will have an .img.xz extention. This is a compressed sector-by-sector image of the SD card, so it is substantial in size.


Step #2: Install the 7-zip compression utility Download and install 7-zip from [1]


Step #3: Decompress the image Use 7-zip to decompress the SD card .img file


Step #4: Install SD card programming utility Download and install Win32DiskImager for Windows from the Ubuntu Wiki page. Be sure to download the binary distribution.

https://wiki.ubuntu.com/Win32DiskImager

Some general help on programming microSD / SD cards can be found on the Win32DiskImager page below.

https://wiki.ubuntu.com/Win32DiskImager/iso2usb

Step #5: Connect SD card to your computer Use a microSD card to SD adapter or a USB adapter to connect the SD card to your computer.


Step #6: Write the image to your SD card Use the instructions on the page to write the decompressed image to your SD card.

Note: You may see a warning about damaging your device. This is fine to accept as long as you are pointing to your SD card for writing.
Note: You should NOT have your VSC8531BB1G connected to your computer at this time.


Step #7: Eject the SD card Eject the newly programmed SD card.


Step #8: Boot your board off of the SD card Insert SD card into your (powered-down) board, hold down the USER/BOOT button and apply power using the +5V DC adapter.

If you desire to write the image to your on-board eMMC, you'll need to follow the instructions at http://elinux.org/Beagleboard:BeagleBoneBlack_Debian#Flashing_eMMC. When the flashing is complete, all 4 USRx LEDs will be steady on or off. The latest Debian flasher images automatically powers down the board upon completion. This can take up to 45 minutes so please be patient. Again, ensure that all LED activity has stopped before attempting to power-down your board - if this doesn't happen automatically - by removing the power adapter cable, remove the SD card and then plug in the power adapter cable to complete the process.

Other currently available software images Some of the starting images below involve multiple steps to produce an SD card image or otherwise change some of the steps above, so be sure to read all the instructions on their pages. Choose the starting point you want, download or produce the SD card image and follow the steps above.

Supported Distributions

At the time of release, not all of these distributions support BeagleBone Black, but should soon.

Texas Instruments releases: Android, Linux, StarterWare (no OS) Linux: Debian, Angstrom Distribution, Ubuntu, ArchLinux, Gentoo, Sabayon, Buildroot, Erlang, Fedora Other: QNX, FreeBSD

Creative Commons Attribute-ShareAlike 3.0 Unported License

This work is licensed under the Creative Commons Attribution-Share Alike 3.0 Unported License. To
view a copy of this license, visit creativecommons.org or send a letter to:

Creative Commons
171 Second Street, Suite 300
San Francisco, California, 94105, USA.
This page is a derivative work of http://www.elinux.org/Beagleboard:BeagleBoneBlack
and is attributed to the work originally created by Gerald Coley of BeagleBoard.org.

For more information, see Creative Commons Attribution-ShareAlike 3.0 Unported License