Difference between revisions of "Minnowboard:Lures Specifications"
m (Added "Lizzy Lure" nickname to the mini PCIe/mSATA lure) |
|||
(15 intermediate revisions by 3 users not shown) | |||
Line 68: | Line 68: | ||
* EEPROM | * EEPROM | ||
* PWM Controlled RGB LED | * PWM Controlled RGB LED | ||
− | * [[Beacon_Lure|Beacon Lure Page]] | + | * [[MinnowBoard:Beacon_Lure|Beacon Lure Page]] |
== Trainer Lure == | == Trainer Lure == | ||
Line 77: | Line 77: | ||
* EEPROM | * EEPROM | ||
* Trainer Lure Page | * Trainer Lure Page | ||
− | * [[Trainer_Lure| Trainer Lure Wiki Page]] | + | * [[MinnowBoard:Trainer_Lure| Trainer Lure Wiki Page]] |
== LVDS Lure == | == LVDS Lure == | ||
Line 87: | Line 87: | ||
* LVDS Lure Page | * LVDS Lure Page | ||
− | == MiniPCIe / mSATA Lure == | + | == MiniPCIe / mSATA Lure(aka 'Lizzy' Lure) == |
* Type-A Lure | * Type-A Lure | ||
Line 94: | Line 94: | ||
* mSATA Connector | * mSATA Connector | ||
− | == | + | == Break-out-Board(aka 'BOB' Lure) == |
* Type-C Lure | * Type-C Lure | ||
Line 101: | Line 101: | ||
** spi | ** spi | ||
** gpio | ** gpio | ||
− | ** | + | ** UARTs |
+ | ** usb host | ||
+ | * [[MinnowBoard:Bob_Lure| BOB Lure Wiki Page]] | ||
== I/O Pad == | == I/O Pad == | ||
Line 110: | Line 112: | ||
* 2x10 Character LCD | * 2x10 Character LCD | ||
* EEPROM | * EEPROM | ||
+ | |||
+ | == Automotive == | ||
+ | |||
+ | * CAN bus interfaces | ||
+ | * 12V power input | ||
+ | * 12V switched power rails | ||
+ | * Voltage Sampling | ||
+ | * [[MinnowBoard:Automotive Lure| Automotive Lure wiki page]] | ||
+ | |||
+ | = Hardware References = | ||
+ | |||
+ | * [[media:minnow-lure-base.tar.gz|Eagle Library for Minnow Lures]] | ||
[[Category: MinnowBoard]] | [[Category: MinnowBoard]] | ||
[[Category: MinnowBoard Expansion Boards]] | [[Category: MinnowBoard Expansion Boards]] | ||
− | [[Category: | + | [[Category: CircuitCo]] |
Revision as of 19:42, 13 October 2013
NOTE: The Lure Board Specifications are under development and are a "work in progress"
Lure Types
Type A
- 106.68mm x 106.68mm (4.2" x 4.2")
- Connector A99244-ND Female (digikey part number)
- Mated height 17mm (when mated with 5mm base)
- Hex Standoff 24436K-ND (digikey part number)
- Placement over top of board
- Four mounting holes at edges of minnow
Type B
- 62.25mm x 106.68mm (2.45" x 4.2")
- Connector A99231TR-ND Female (digikey part number)
- Mated height 10mm (when mated with 5mm base)
- Hex Standoff 24433K-ND (digikey part number)
- Placement over top of board
- Two screw mounting holes in center of minnow
Type-C
- 62.25mm x 62.25mm (2.45" x 2.45")
- Connector A99192TR-ND Female (digikey part number)
- Mated height 6mm (when mated with 5mm base)
- No mounting standoffs (needs review)
- Extends from side of minnow board
- No mount holes (needs review)
Lure Features
Minnow Board and Passthrough
- Connector A99205CT-ND Male (digikey part number)
- Mated height base 5mm (plus female connector height)
EEPROM
- i2c eeprom
- recommended size 256k
- CAT24C256W
- configurable for address
LVDS Interface
- single FPDLink-I interface (aka LVDS LCD interface)
- 18 or 24 bpp support
- Max pixel clock of 68MHz
- Max resolution 1366x768 (approximately 1120000 total pixels)
- Embedded Media Graphics Driver support
- UEFI controls (??)
- backlight PWM controls
- LVDS Controls Reference Documentation from Intel
- FPDLink-I to RGB888 bridge(aka LVDS to parallel)
- Presentation and References for LCD interfaces
Reference Lures
Beacon Lure
- Type-C Lure
- 7 Segment Display via Shift Register
- EEPROM
- PWM Controlled RGB LED
- Beacon Lure Page
Trainer Lure
- Type-A Lure
- Atmel AVR (Arduino Compatible)
- Prototype Area
- EEPROM
- Trainer Lure Page
- Trainer Lure Wiki Page
LVDS Lure
- Type-B Lure
- Backlight Power supply
- FPDLink-I connector (aka LVDS)
- EEPROM
- LVDS Lure Page
MiniPCIe / mSATA Lure(aka 'Lizzy' Lure)
- Type-A Lure
- EEPROM
- miniPCIe Connector
- mSATA Connector
Break-out-Board(aka 'BOB' Lure)
- Type-C Lure
- Breakout for all low speed signals
- i2c
- spi
- gpio
- UARTs
- usb host
- BOB Lure Wiki Page
I/O Pad
- Type-B Lure
- 5 buttons
- 5 LEDS
- 2x10 Character LCD
- EEPROM
Automotive
- CAN bus interfaces
- 12V power input
- 12V switched power rails
- Voltage Sampling
- Automotive Lure wiki page