Difference between revisions of "Minnowboard:MaxLures"
(clean ups) |
(clean ups) |
||
| Line 147: | Line 147: | ||
== Prototype Lure == | == Prototype Lure == | ||
| − | + | {| width="100%" | |
| − | * Generic Prototype Area on 0.1" grids | + | |- style="vertical-align:top;" |
| − | [[File:Prototype-lure-b.jpg| | + | | Generic Prototype Area on 0.1" grids |
| + | <br/> | ||
| + | {| width="100%" | ||
| + | |- style="vertical-align:top;" | ||
| + | | | ||
| + | * '''Features:''' | ||
| + | ** Generic Prototype Area on 0.1" grids | ||
| + | | | ||
| + | * '''Produced by:''' CircuitCo | ||
| + | * Additional Information: none available right now | ||
| + | |||
| + | |||
| + | * '''Available from:''' | ||
| + | ** [http://www.technodisti.com/online-store/boards/prototype-lure-detail.html Technodisti] | ||
| + | |} | ||
| + | | | ||
| + | [[File:Prototype-lure-b.jpg|80px]] | ||
| + | [[File:ProtoLure-SlantedSide01-650.jpg|400px]] | ||
| + | |- | ||
| + | | | ||
| + | |||
* '''Design Files:''' | * '''Design Files:''' | ||
**[http://www.elinux.org/images/d/d9/Proto_Lure_A1.zip EAGLE design files] | **[http://www.elinux.org/images/d/d9/Proto_Lure_A1.zip EAGLE design files] | ||
| Line 155: | Line 175: | ||
**[http://www.elinux.org/images/9/97/Proto_Lure_A1_BOM.zip Bill of Materials] | **[http://www.elinux.org/images/9/97/Proto_Lure_A1_BOM.zip Bill of Materials] | ||
**[http://www.elinux.org/images/6/60/Proto_Lure_A1_Schematic.pdf Schematic (PDF)] | **[http://www.elinux.org/images/6/60/Proto_Lure_A1_Schematic.pdf Schematic (PDF)] | ||
| + | |} | ||
== Cuttle(bone) Lure == | == Cuttle(bone) Lure == | ||
Revision as of 17:55, 17 December 2014
Minnowboard Max Lure Information
Contents
Planned Lures
Calamari Lure
| Break out board intended mainly for testing gpio and low speed interfaces, as
|
 | ||
|
Ika Lure
The Ika lure takes the existing low speed I/O and expands it (through I2C chips) to allow for an Arduino compatible shield to be used with the MinnowBoard MAX.
|
  |
Seacat Lure
| mPCI-E and mSATA break out board
|
 | ||
|
Jetsam Lure
| mPCI-E break out board
|
 | ||
|
Flotsam Lure
| mSATA break out board
|
 | ||
|
Prototype Lure
| Generic Prototype Area on 0.1" grids
|
| ||
|
Cuttle(bone) Lure
Adapter from Low Speed Connector I/O (I2C,I2S,UARTs,SPI,GPIO) to BeagleBone * Capes. Works with a variety of Capes but not all.
- Design Files:
- Schematic(PDF)
- Project files on Github
- Schematic(PDF)
Nic Lure
- Single Gigabit Ethernet
Can Bus Lure
- standard CAN Bus
- Option for STN1110
RS-485 Lure
- standard RS-485
RS-232 Lure
- 2 DB-9 connectors
Relay Cape
- 4 Relays
- GPIO Controls
USB Hub Lure
- 4 USB Host Ports
PWM Lure
- 32 PWM Outputs
ADC Lure
- 8 ADC inputs
Moto Lure
- Dual H-Bridge
Audio Lure
- Analog Audio Ouput
- Analog Audio Input
MiniDisplay Lure
- SPI Based TFT Display
- 2.8"
- 4-Wire Resistive Touch
