R-Car/Boards/M3NSK

From eLinux.org
< R-Car
Revision as of 18:31, 8 July 2020 by Y.H. (talk | contribs)
Jump to: navigation, search


Introduction

This is the Wiki for the Renesas R-Car Starter Kit Pro board(M3N).

Typename: RTP0RC77965SKBX010SA00

Topic

Note : There are no plans to manufacture the R-Car Starter kit Pro(M3N).

SW Release Information

Board name SW name Release date Note
R-Car Starter Kit ( Premier / Pro ) Yocto v4.1.0 2020/08/06 This version does not support MMP.
GFX(except for Wayland/weston) is supported from 2020/09/23.
Yocto v3.21.0 2019/07/09 New R-Car Starter Kit Pro(RTP8J77961ASKB0SK0SA05A) is supported from 2020/07/10.
Kingfisher Infotainment Board Android P [New!!] 2020/09/29 Only R-Car Starter Kit Premier(R-Car H3) + Kingfisher is supported.
Yocto v3.21.0 2019/08/07 To check for latest information, please refer to the meta-rcar.
New R-Car Starter Kit Pro(RTP8J77961ASKB0SK0SA05A) is supported from 2020/08/02.


Quick Start How To

Build Yocto image

Refer to Yocto for steps necessary for making a Yocto image.

Connect 5 V power supply to the board

Use 5 V power supply with a 5.5 mm barrel plug. The power supply should be able to provide 4(Min) ~ 8(Max)Amps.

Note

  • The recommended value is 8 Amps. But, user can use 4 Amps. and 6 Amps. (depends on the use case).

Booting Linux

* Kernel config: defconfig
* Kernel image: arch/arm64/boot/Image
* DTB: arch/arm64/boot/dts/renesas/r8a77965-m3nulcb.dtb
* DTB: arch/arm64/boot/dts/renesas/r8a77965-m3nulcb-kf.dtb

U-Boot boot command:

tftpboot 0x48080000 Image
tftpboot 0x48000000 r8a77965-m3nulcb(-kf).dtb 
booti 0x48080000 - 0x48000000

Flashing firmware

Writing data
Filename Program Top Address Flash Save Address Description
bootparam_sa0.srec 0xE6320000 0x000000 Loader(Boot parameter)
bl2-m3nulcb.srec 0xE6304000 0x040000 Loader
cert_header_sa6.srec 0xE6320000 0x180000 Loader(Certification)
bl31-m3nulcb.srec 0x44000000 0x1C0000 ARM Trusted Firmware
tee-m3nulcb.srec 0x44100000 0x200000 OP-Tee
u-boot-elf.srec 0x50000000 0x640000 U-Boot
  1. Power off the board
  2. Press SW8
    
  3. Set SW and JP as follows:
  4. SW1=OFF
    SW6[1]=ON, SW6[2]=ON, SW6[3]=OFF, SW6[4]=ON
    JP1 -> 1-2 short
    
  5. Power on the board
  6. Press SW8
    Minimonitor starts and provides prompts on console
    
  7. Change SW as follows:
  8. SW1=ON
    SW6[all]=ON
    
  9. Flash bootparam_sa0.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs:
  10. 3
    y
    y
    e6320000
    0
    type "ctrl+A S" and select upload method "ascii", then choose file for uploading "bootparam_sa0.srec", after upload finished press any key
    y
    
  11. Flash bl2-m3nulcb.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs:
  12. 3
    y
    y
    e6304000
    40000
    type "ctrl+A S" and select upload method "ascii", then choose file for uploading "bl2-m3nulcb.srec", after upload finished press any key
    y
    
  13. Flash cert_header_sa6.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs:
  14. 3
    y
    y
    e6320000
    180000
    type "ctrl+A S" and select upload method "ascii", then choose file for uploading "cert_header_sa6.srec", after upload finished press any key
    y
    
  15. Flash bl31-m3nulcb.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs:
  16. 3
    y
    y
    44000000
    1C0000
    type "ctrl+A S" and select upload method "ascii", then choose file for uploading "bl31-m3nulcb.srec", after upload finished press any key
    y
    
  17. Flash tee-m3nulcb.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs:
  18. 3
    y
    y
    44100000
    200000
    type "ctrl+A S" and select upload method "ascii", then choose file for uploading "tee-m3nulcb.srec", after upload finished press any key
    y
    
  19. Flash u-boot-elf.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs:
  20. 3
    y
    y
    50000000
    640000
    type "ctrl+A S" and select upload method "ascii", then choose file for uploading "u-boot-elf.srec", after upload finished press any key
    y
    
  21. Reset the board
  22. Press SW9
    

Test procedures

Audio

Ex) In the case of "r8a77965-m3nulcb.dtb"

amixer set "DVC Out" 1%
aplay sample.wav

Ex) In the case of "r8a77965-m3nulcb-kf.dtb"

amixer -c ak4613 set "DVC Out" 1%
aplay sample.wav

Q&A site

http://renesasrulz.com/r-car-h3-m3-cockpit/

FAQ page

https://elinux.org/R-Car/Boards/Yocto-Gen3-CommonFAQ