R-Car/Boards/M3NSK

From eLinux.org
< R-Car
Revision as of 23:29, 29 June 2021 by Y.H. (talk | contribs) (Add footer template)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
Software for Starter Kit
Software for Kingfisher
Software for CCPF-SK
Boards
Packages
Q&A / FAQ
Partner solution search
(External link)
Solutions


Introduction

This is the Wiki for the Renesas R-Car Starter Kit Pro board(M3N). 

Typename: RTP0RC77965SKBX010SA00

Topic

Note : There are no plans to manufacture the R-Car Starter kit Pro(M3N).

EOL Notification of the M3SK

Production of M3SK is discontinued.
See M3SK page for detail.

The new version of R-Car Starter Kit Premier is now on sale !!

  • Equipped with R-Car H3e-2G
    (En) https://www.renesas.com/jp/en/about/press-room/renesas-launches-r-car-gen3e-20-percent-higher-cpu-speed-automotive-infotainment-cockpit-and-digital
    (Zh) https://www.renesas.com/jp/zh/about/press-room/renesas-launches-r-car-gen3e-20-percent-higher-cpu-speed-automotive-infotainment-cockpit-and-digital
    (Jp) https://www.renesas.com/jp/ja/about/press-room/renesas-launches-r-car-gen3e-20-percent-higher-cpu-speed-automotive-infotainment-cockpit-and-digital
  • CPU performance is increased 20% by supporting up to 2GHz frequency over past products.
  • You can buy from here.

SW Release Information

Board name SW name Release date Note
R-Car Starter Kit ( Premier / Pro ) Yocto v5.9.0 (stable) [New!!] 2022/02/08
Kingfisher Infotainment Board Yocto v5.9.0 (stable) [New!!] 2022/02/14 To check for latest information, please refer to the meta-rcar/tree/v5.9.0.
Android 10 (stable) 2021/07/26 R-Car Starter Kit Premier(R-Car H3) + Kingfisher is supported.
R-Car Starter Kit Pro(RTP8J77961ASKB0SK0SA05A) + Kingfisher is also supported from 2021/11/25.
Android P (stable) 2020/09/29 R-Car Starter Kit Premier(R-Car H3) + Kingfisher is supported.
R-Car Starter Kit Pro(RTP8J77961ASKB0SK0SA05A) + Kingfisher is also supported from 2021/03/16.
CCPF-SK Board Yocto v5.9.0 (stable) [New!!] 2022/02/08 Prebuilt binary is available in Quick startup guide page. (Updated on 2022/03/18)


Quick Start How To

Build Yocto image

Refer to Yocto for steps necessary for making a Yocto image.

Connect 5 V power supply to the board

Use 5 V power supply with a 5.5 mm barrel plug. The power supply should be able to provide 4(Min) ~ 8(Max)Amps.

Note

  • The recommended value is 8 Amps. But, user can use 4 Amps. and 6 Amps. (depends on the use case).

Booting Linux

* Kernel config: defconfig
* Kernel image: arch/arm64/boot/Image
* DTB: arch/arm64/boot/dts/renesas/r8a77965-m3nulcb.dtb
* DTB: arch/arm64/boot/dts/renesas/r8a77965-m3nulcb-kf.dtb

U-Boot boot command: 

tftpboot 0x48080000 Image
tftpboot 0x48000000 r8a77965-m3nulcb(-kf).dtb 
booti 0x48080000 - 0x48000000

Flashing firmware

Writing data
Filename Program Top Address Flash Save Address Description
bootparam_sa0.srec 0xE6320000 0x000000 Loader(Boot parameter)
bl2-m3nulcb.srec 0xE6304000 0x040000 Loader
cert_header_sa6.srec 0xE6320000 0x180000 Loader(Certification)
bl31-m3nulcb.srec 0x44000000 0x1C0000 ARM Trusted Firmware
tee-m3nulcb.srec 0x44100000 0x200000 OP-Tee
u-boot-elf.srec 0x50000000 0x640000 U-Boot
  1. Power off the board 
    2. Press SW8
  2. Set SW and JP as follows: 
    3. SW1=OFF
SW6[1]=ON, SW6[2]=ON, SW6[3]=OFF, SW6[4]=ON
JP1 -> 1-2 short
  3. Power on the board 
    4. Press SW8
Minimonitor starts and provides prompts on console
  4. Change SW as follows: 
    5. SW1=ON
SW6[all]=ON
  5. Flash bootparam_sa0.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
    6. 3
y
y
e6320000
0
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "bootparam_sa0.srec", after upload finished press any key
y
  6. Flash bl2-m3nulcb.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
    7. 3
y
y
e6304000
40000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "bl2-m3nulcb.srec", after upload finished press any key
y
  7. Flash cert_header_sa6.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
    8. 3
y
y
e6320000
180000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "cert_header_sa6.srec", after upload finished press any key
y
  8. Flash bl31-m3nulcb.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
    9. 3
y
y
44000000
1C0000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "bl31-m3nulcb.srec", after upload finished press any key
y
  9. Flash tee-m3nulcb.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
    10. 3
y
y
44100000
200000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "tee-m3nulcb.srec", after upload finished press any key
y
  10. Flash u-boot-elf.srec. In console execute xls2 command (load program to hyper flash) and provide the following inputs: 
    11. 3
y
y
50000000
640000
type "ctrl+A S" and select upload method "ascii", then choose file for uploading "u-boot-elf.srec", after upload finished press any key
y
  11. Reset the board 
    12. Press SW9

Test procedures

Audio

Ex) In the case of "r8a77965-m3nulcb.dtb" 

amixer set "DVC Out" 1%
aplay sample.wav

Ex) In the case of "r8a77965-m3nulcb-kf.dtb" 

amixer -c ak4613 set "DVC Out" 1%
aplay sample.wav


Q&A site

https://community.renesas.com/automotive/r-car-h3-m3-cockpit/

FAQ site

Retrieved from "https://elinux.org/index.php?title=R-Car/Boards/M3NSK&oldid=553196"