Difference between revisions of "R-Car/Boards/Salvator-XS"

From eLinux.org
Jump to: navigation, search
m (Wake-Up Sources)
m (Add blank lines)
Line 5: Line 5:
 
This is the Wiki for the Renesas R-Car H3 ES2.0 and M3-W Salvator-XS (Salvator-X 2nd version) board (RTP0RC7795SIPB0012S resp. RTP0RC7796SIPB0012S).
 
This is the Wiki for the Renesas R-Car H3 ES2.0 and M3-W Salvator-XS (Salvator-X 2nd version) board (RTP0RC7795SIPB0012S resp. RTP0RC7796SIPB0012S).
 
Refer to the [[R-Car]] page for information about Renesas' R-Car SoC family.
 
Refer to the [[R-Car]] page for information about Renesas' R-Car SoC family.
 +
  
 
= Serial Console =
 
= Serial Console =
Line 10: Line 11:
 
Use a micro-USB cable to connect to "Debug Serial 0".
 
Use a micro-USB cable to connect to "Debug Serial 0".
 
Serial settings are 115200 8N1.
 
Serial settings are 115200 8N1.
 +
  
 
= Booting Linux =
 
= Booting Linux =
Line 25: Line 27:
 
booti 0x48080000 - 0x49f00000
 
booti 0x48080000 - 0x49f00000
 
</pre>
 
</pre>
 +
  
 
= Suspend-to-RAM =
 
= Suspend-to-RAM =
Line 78: Line 81:
 
* sh-sci (Serial): Disabled by default
 
* sh-sci (Serial): Disabled by default
 
* usb: Disabled by default
 
* usb: Disabled by default
 +
  
 
= Remote Control =
 
= Remote Control =

Revision as of 05:50, 13 November 2017

Introduction

This is the Wiki for the Renesas R-Car H3 ES2.0 and M3-W Salvator-XS (Salvator-X 2nd version) board (RTP0RC7795SIPB0012S resp. RTP0RC7796SIPB0012S). Refer to the R-Car page for information about Renesas' R-Car SoC family.


Serial Console

Use a micro-USB cable to connect to "Debug Serial 0". Serial settings are 115200 8N1.


Booting Linux

 * Kernel config: defconfig
 * Kernel image: arch/arm64/boot/Image
 * DTB: arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb (for R-Car H3)
 * DTB: arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb (for R-Car M3-W)

U-Boot boot command:

tftpboot 0x48080000 Image
tftpboot 0x49f00000 r8a7795-salvator-xs.dtb (for R-Car H3)
tftpboot 0x49f00000 r8a7796-salvator-xs.dtb (for R-Car M3-W)
booti 0x48080000 - 0x49f00000


Suspend-to-RAM

PSCI System Suspend

The system can be suspended by triggering a PSCI System Suspend:

echo mem > /sys/power/state

Caveats:

  • Before you can use the above, you must configure the PMIC for DDR Backup Mode first, using the command below, followed by switching SW23 off. Note that this must be repeated after each wake-up.
i2cset -f -y 7 0x30 0x20 0x0F
  • PSCI System Suspend supports wake-up by PMIC only. Switch SW23 on to resume the system.

Suspend-to-Idle

If you want to suspend the system, and wake up through other wake-up sources, you must use Suspend-to-Idle instead of PSCI System Suspend.

The system can be suspended ("frozen") using:

echo freeze > /sys/power/state

Alternatively (since v4.10), you can configure the system to use Suspend-to-Idle by default:

echo s2idle > /sys/power/mem_sleep

After that, you can suspend the system using the standard:

echo mem > /sys/power/state

Wake-Up Sources

Suspend-to-Idle supports the following wake-up sources:

  • gpio-keys: Not enabled in the upstream kernel due to sharing of GPIOs between switches and LEDs, but see Remote Control below.
  • ravb (Ethernet): Configure using one of:
ethtool -s eth0 wol g # Enable wake on MagicPacket
ethtool -s eth0 wol d # Disable

Wake-up by sending a MagicPacket from another system using:

wakeonlan <mac-address> | <ip-address> # <ip-address> must be in /etc/ethers
  • sh-sci (Serial): Disabled by default
  • usb: Disabled by default


Remote Control

Operation Signal A Pin A Signal B Pin B Connector needed Comments
Reset #MRB/SYSRSTn EXIO-D pin 66 GND EXIO-D pin 58 Samtec QTE-020 or -040
Wake-Up IRQ1n/GP2_01 EXIO-D pin 50 GND EXIO-D pin 46 Samtec QTE-020 or -040 Needs arm64: dts: salvator-common: Enable GP2_1 for wake-up
ACC OFF #RSTB/EX_PWRONn EXIO-D pin 68 D5.0V CN7 pin 4 Samtec QTE-020 or -040, and 5¼ HDD power Pull high via 10K resistor to power off