What does it do?
This project configures your Raspberry Pi to connect to the Internet through ethernet, and share that connection over WiFi.
What do you need?
- A Raspberry Pi, model B.
- A boot SD card for the Raspberry Pi.
- A USB WiFi device that supports "Access Point" mode.
- An Ethernet cable to connect to the local network.
What skill level is required?
This project does not require any coding or compilation. Very basic Linux and networking knowledge would be useful, but not essential.
To edit a configuration file (for example /etc/udhcpd.conf) use the following command
sudo nano /etc/udhcpd.conf
You will find yourself in a simple editor. Move around using the arrow keys. To save the file press Ctrl-o. To exit press Ctrl-x.
How does it work?
The Raspberry Pi is configured as a WiFi Hotspot, just like you would see in an internet cafe. It allows you to connect to the internet over WiFi using the Raspberry Pi as the bridge to the internet. The basic steps are
- Enable a WiFi Access Point and broadcast on the channel of your choice
- Assign dynamic IP addresses to any device that connects to WiFi network
- Join the WiFi and Ethernet networks together by using Network Address Translation
The following steps were performed on Raspbian but should be much the same on any Debian-based distro.
1. Install the necessary software.
sudo apt-get install hostapd udhcpd
2. Configure DHCP. Edit the file /etc/udhcpd.conf and configure it like this:
start 192.168.2.2 # This is the range of IPs that the hostspot will give to client devices. end 192.168.2.20 interface wlan0 # The device uDHCP listens on. remaining yes opt dns 22.214.171.124 126.96.36.199 # The DNS servers client devices will use. opt subnet 255.255.255.0 opt router 192.168.2.1 # The Pi's IP address on wlan0 which we will set up shortly. opt lease 864000 # 10 day DHCP lease time in seconds
Edit the file /etc/default/udhcpd and change the line:
You will need to give the Pi a static IP address with the following command:
sudo ifconfig wlan0 192.168.2.1
To set this up automatically on boot, edit the file /etc/network/interfaces and replace the line "iface wlan0 inet dhcp" to:
iface wlan0 inet static address 192.168.2.1 netmask 255.255.255.0
If the line "iface wlan0 inet dhcp" is not present, add the above lines to the bottom of the file.
Change the lines (they probably won't all be next to each other):
allow-hotplug wlan0 wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet manual
#allow-hotplug wlan0 #wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf #iface default inet dhcp
3. Configure HostAPD. You can create an open network, or a WPA-secured network. A secure network is recommended to prevent unauthorized use and tampering, but you can also create an open network. To create a WPA-secured network, edit the file /etc/hostapd/hostapd.conf (create it if it doesn't exist) and add the following lines:
interface=wlan0 driver=nl80211 ssid=My_AP hw_mode=g channel=6 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=My_Passphrase wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP
Change ssid=, channel=, and wpa_passphrase= to values of your choice. SSID is the hotspot's name which is broadcast to other devices, channel is what frequency the hotspot will run on, wpa_passphrase is the password for the wireless network. For many, many more options see the file /usr/share/doc/hostapd/examples/hostapd.conf.gz
If you would like to create an open network, put the following text into /etc/hostapd/hostapd.conf:
interface=wlan0 ssid=My_AP hw_mode=g channel=6 auth_algs=1 wmm_enabled=0
Change ssid= and channel= to values of your choice. Note that anyone will be able to connect to your network, which is generally not a good idea. Also, some regions will hold an access point's owner responsible for any traffic that passes though an open wireless network, regardless of who actually caused that traffic.
Edit the file /etc/default/hostapd and change the line:
4. Configure NAT. NAT (Network Address Translation) is a technique that allows several devices to use a single connection to the internet. Linux supports NAT using Netfilter (also known as iptables), and if fairly easy to set up. First, edit the file /etc/sysctl.conf and add the following line to the bottom of the file:
This will enable NAT in the kernel. Second, run the following commands:
sudo iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE sudo iptables -A FORWARD -i eth0 -o wlan0 -m state --state RELATED,ESTABLISHED -j ACCEPT sudo iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT
Your Pi is now NAT-ing. To make this permanent so you don't have to run the commands after each reboot, run the following command:
sudo sh -c "iptables-save > /etc/iptables.ipv4.nat"
Now edit the file /etc/network/interfaces and add the following line to the bottom of the file:
up iptables-restore < /etc/iptables.ipv4.nat
5. Fire it up! Run the following commands to start the access point:
sudo service hostapd start sudo service udhcpd start
Your Pi should now be hosting a wireless hotspot. To get the hotspot to start on boot, run these additional commands:
sudo update-rc.d hostapd enable sudo update-rc.d udhcpd enable
At the completion of these instructions, your Pi should be providing a wireless network and allowing other devices to connect to the Internet. From my experience, the Pi makes a decent access point, although with cheaper WiFi dongles range will be fairly limited. I haven't stress tested this setup, but it seems to work fairly well and is handy when a "real" access point isn't available. I wrote most of the instructions from memory, if you find any errors/typos I'll correct them.
This tutorial originally was a post on the Raspberry Pi forum here, you can reply to that topic if you have issues. Thanks go to all the people who tested my tutorial on the forum, and to poing who contributed the WPA HostAPD config.