Hardware & Peripherals:
Hardware - detailed information about the Raspberry Pi boards.
Hardware History - guide to the Raspberry Pi models.
Low-level Peripherals - using the GPIO and other connectors.
Expansion Boards - GPIO plug-in boards providing additional functionality.
Screens - attaching a screen to the Raspberry Pi.
Cases - lots of nice cases to protect the Raspberry Pi.
Other Peripherals - all sorts of peripherals used with the Raspberry Pi.
The following display outputs are supported on the board:
- Composite video (NTSC and PAL) via an RCA plug (the yellow socket on your TV) or SCART socket.
- HDMI 1.3a standard output.
- Display Serial Interface (DSI) - via unpopulated 15-way flat flex connector.
These interfaces allow the use of a broad range of displays, including:
- Televisions (HDMI or composite).
- Computer monitors (HDMI/DVI-D cable) (VGA monitors would require either a composite or HDMI to VGA or component scan converter box).
- DLP/Laser Pico Projectors (HDMI/DVI-D cable).
- RAW LCD panels (DSI + interfacing hardware)
- Composite and HDMI outputs can not be used at the same time (one or the other.)
Directly from the board.
With an inexpensive passive HDMI to DVI-D cable or convertor.
Composite video (NTSC and PAL) via an RCA plug, directly from the board.
The Broadcom BCM2835 only provides HDMI output and composite output. RGB and other signals needed by RGB, S-VIDEO or VGA connectors are however not provided.
A couple of options for VGA or component RGB outputs, bridging from either HDMI or the MIPI DSI interface:
Firstly, the following *might* work. Beagleboard people have reported various levels of success (mainly "issues"):
...it may need to be modified as described here:
Alternatively, it may be possible to design an expansion board that plugs into the LCD headers on the R.Pi. Here is something similar for Beagleboard:
Some more converters that should work:
- $24.00 "Video Converter adapter" from china
- $24.00 ASUS - Video adapter requires additional miniHDMI to standard HDMI adapter
- $32.50 HDMI to VGA Video Converter
- $39.99 HDCP HDMI to VGA + SPDIF RGB Component Ypbpr Converter
- $48.00 HP HDMI to VGA Display Adapter
Potential RGB interfacing chips:
They emit Hsync, Vsync and RGB w/ about 8 bits each (sometimes, it's called "MIPI DPI")
- Toshiba TC358762XBG deserializer bridge chip
- Analog Devices HDMI Receivers
- Renesas µPD60800 Intelligent Buffer IC
- Renesas µPD60801 Intelligent Buffer IC
This one outputs analog RGB, but is hard to find (obsolete?):
- [www.datasheets.org.uk/dl/Datasheets-36/DSA-705489.pdf TFP9431 DVI RECEIVER WITH TRIPLE DAC]
The SOC (system on a chip) does not support any kind of analog component video, including VGA, since the SOC is designed for mobile phone use where this would not be a requirement. Additional componenty would be needed to generate RGB signals. Additional componentry would push the price beyond the $25 target and therefore won't happen.
interfacing to Raw LCD panels
Nokia N900 has 800x480 DCS LCD (afaik its like DSI, but has build in framebuffer). Replacement screen is about ~$40 (~$50 with 4pin resistive touchscreen).
Nokia N8 has AMOLED 360x640 pixels DSI LCD. Replacement screen is about ~$35, another ~$25 for Multitouch Synaptics T1021A touchscreen (I2C + interrupt IO, no docs/drivers).
The schematics for apples iPhone 3gs and 4g suggest they speak DSI, thus they can probably be connected directly. The older iPhones use a "Mobile Pixel Link" connection from National Semiconductor. The 3GS panel (480×320) goes as low as US $14.88, while the 4G one (960×640) can be had for US $17.99.
Other panels with MIPI DSI: www.panelook.com
Potential LVDS interfacing chips:
DVI receiver TFP401A, TFP403, or TFP501 + LVDS transmitter SN75LVDS83B or SN65LVDS93A (Mentioned earlier fit-VGA is build around TFP401A, probably many more "active" DVI2VGA cables are build the same way)
16x2 LCD Displays
The old-style 2-line, 16-character LCD displays can be commonly controlled over UART, thus providing a cheap way to display values for sensors etc.