Difference between revisions of "RZ-G/Boards/SK-RZG1E:Hardware"
Renesas-rz (talk | contribs) (Created page with "TBD") |
Renesas-rz (talk | contribs) m |
||
Line 1: | Line 1: | ||
+ | {{TOC right}} | ||
+ | This page contains information on the [[RZ-G/Boards/SK-RZG1E]] hardware. | ||
+ | == Board Layout == | ||
+ | [[File:IslayTopWithLabels.png|794px|Top view]]<br/> | ||
+ | [[File:IslayBottomWithLabels.png|662px|Bottom view]]<br/> | ||
+ | |||
+ | == Power Plug == | ||
+ | [[File:Centre-positive.svg|right|thumb|120px|Center Positive 5V connector]] | ||
+ | The RZ/G1E Starter Kit board uses a 5.5 x 2.1mm barrel 5V power plug. It is a Center Positive power supply, indicating that the center (tip) of the output plug is positive (+) and the outer barrel is negative (-). | ||
+ | * North American Power Supply from Digikey - 5V@2.5A -[http://www.digikey.com/product-detail/en/EPSA050250U-P5P-EJ/T1058-P5P-ND/2235250 CUI EPSA050250U-P5P-EJ] | ||
+ | * European Power Supply from Digikey - 5V@2.5A - [http://www.digikey.com/product-detail/en/EPSA050250UE-P5P-EJ/T1150-P5P-ND/2511851 CUI EPSA050250UE-P5P-EJ] | ||
+ | * Power Supply from Sparkfun - 5V@2A - [https://www.sparkfun.com/products/12889 TOL-12889] | ||
+ | * Power Supply from Adafruit - 5V@2A - [http://www.adafruit.com/products/276 PRODUCT-ID:276] | ||
+ | * Power Supply from SeeedStudio - 5V@2A [http://www.seeedstudio.com/depot/Wall-Adapter-Power-Supply-5VDC-2A-p-1508.html?cPath=1_4 SKU: POW06182B] | ||
+ | |||
+ | == Switches and Buttons == | ||
+ | [[File:IslaySwitchesWithLabels.png|931px|Buttons and switches]]<br/> | ||
+ | === SW1 (SSI_DATA1 Routing) === | ||
+ | {| | ||
+ | |- style="vertical-align:middle;" | ||
+ | | rowspan="2" | [[File:Switch.png|100px|Switch pin layout]] | ||
+ | | | ||
+ | {| class="wikitable" | ||
+ | |+ SW1 | ||
+ | |- | ||
+ | ! Function || style="background-color:#ccc;" | Pin 1 side (default) || Pin 3 side | ||
+ | |- | ||
+ | | SSI_SDATA1 Selection | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> U22 <br/> [http://www.akm.com/akm/en/product/datasheet1/?partno=AK4643EN AKM AK4643] <br/> Audio Codec </div> | ||
+ | | <div style="text-align: center;"> U15 <br/> [http://www.analog.com/en/audiovideo-products/analoghdmidvi-interfaces/adv7511/products/product.html ADV7511] <br/> HDMI transmitter </div> | ||
+ | |- | ||
+ | |} | ||
+ | |} | ||
+ | SW1 selects the device to be connected to the SSI_DATA1/ETH_RXD0_B (GP-5-13) pin of the the RZ/G1E SoC. The pin is normally set to receive mode. | ||
+ | {| class="wikitable" | ||
+ | |- | ||
+ | ! Position | ||
+ | ! Function | ||
+ | |- | ||
+ | | style="background-color:#ccc;" | Pin 1 side | ||
+ | | style="background-color:#ccc;" | | ||
+ | * Connects the SSI_DATA1/ETH_RXD0_B pin of the RZ/G1E SoC to the SDTO pin 12 of the [http://www.akm.com/akm/en/product/datasheet1/?partno=AK4643EN AK4643] | ||
+ | * The SSI_DATA1 pin of the RZ/G1E SoC must be set to input. | ||
+ | |- | ||
+ | | Pin 3 side | ||
+ | | | ||
+ | * Connects the SSI_DATA1/ETH_RXD0_B pin of the RZ/G1E SoC to the I2S1 pin (pin 6) of the [http://www.analog.com/en/audiovideo-products/analoghdmidvi-interfaces/adv7511/products/product.html Analog Devices ADV7511]. | ||
+ | * The SSI_DATA1 pin of the RZ/G1E SoC should be set to output. | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | === SW2 (TRST# Pull-up) === | ||
+ | {| | ||
+ | |- style="vertical-align:middle;" | ||
+ | | rowspan="2" | [[File:SwitchRight.png|100px|Switch pin layout]] | ||
+ | | | ||
+ | {| class="wikitable" | ||
+ | |+ SW2 | ||
+ | |- | ||
+ | ! Function || Pin 1 side || Pin 2 side || style="background-color:#ccc;" | Pin 3 side | ||
+ | |- | ||
+ | | SSI_SDATA1 Selection | ||
+ | | <div style="text-align: center;"> Pulled up </div> | ||
+ | | <div style="text-align: center;"> Reserved </div> | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> Pulled down | ||
+ | |- | ||
+ | |} | ||
+ | |} | ||
+ | SW2 selects whether to pull up or down the TRST# pin of the RZ/G1E SoC JTAG interface. | ||
+ | |||
+ | === SW3, SW4, SW6 (Push Buttons) === | ||
+ | {| | ||
+ | |- style="vertical-align:middle;" | ||
+ | | rowspan="2" | [[File:Pushbutton.png|80px|Pushbutton]] | ||
+ | | | ||
+ | {|class="wikitable" | ||
+ | ! Button # || GPIO pin | ||
+ | |- | ||
+ | | SW3 || GP-5-10/IRQ9 | ||
+ | |- | ||
+ | | SW4 || GP-5-11 | ||
+ | |- | ||
+ | | SW5 || GP-5-12 | ||
+ | |- | ||
+ | |} | ||
+ | |} | ||
+ | The active signal (low or high) for SW3-SW5 is selected by the corresponding bit of POSNEG register. Refer to to the section GPIO in the RZ/G1E Hardware Manual for details. | ||
+ | |||
+ | === SW7 (Mode Setting A) === | ||
+ | {| | ||
+ | |- style="vertical-align:middle;" | ||
+ | | [[File:DipSw2.png|85px|Switch pin layout]] | ||
+ | | | ||
+ | {| class="wikitable" | ||
+ | |+ SW7 | ||
+ | |- | ||
+ | ! No || Function || OFF ||ON | ||
+ | |- | ||
+ | | 1 | ||
+ | | MD21 <br/> JTAG mode | ||
+ | | <div style="text-align: center;"> 1 <br/> Coresight Debug Port </div> | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> 0 <br/> Boundary Scan </div> | ||
+ | |- | ||
+ | | 1 | ||
+ | | MD19 <br/> DDR3-SDRAM bus clock | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> 1 <br/> DD3-1333 </div> | ||
+ | | <div style="text-align: center;"> 0 <br/> Prohibited </div> | ||
+ | |- | ||
+ | |} | ||
+ | |} | ||
+ | MD21 determines the JTAG mode. Select OFF position to use JTAG debugger.<br/> | ||
+ | MD19 determines the SDRAM clock speed. It must remain in OFF position to select DDR3-1333. | ||
+ | |||
+ | === SW9 (SPI Flash Memory Selection) === | ||
+ | {| | ||
+ | |- style="vertical-align:middle;" | ||
+ | | rowspan="2" | [[File:Switch.png|100px|Switch pin layout]] | ||
+ | | | ||
+ | {| class="wikitable" | ||
+ | |+ SW9 | ||
+ | |- | ||
+ | ! Function || style="background-color:#ccc;" | Pin 1 side (default) || Pin 3 side | ||
+ | |- | ||
+ | | SPI Flash memory selection | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> 64 MB U6 <br/> S25FL512SAGMFIG11 </div> | ||
+ | | <div style="text-align: center;"> 4 MB U7 <br/> S25FL032P0XMFI011 </div> | ||
+ | |- | ||
+ | |} | ||
+ | |} | ||
+ | The RZ/G1E Starter Kit board is equipped with 512 Mbits SPI flash memory (U6: S25FL512SAGMFIG11) and 32 Mbits SPI flash memory (U7: S25FL032P0XMFI011). When SW9 is set to the pin 1 side, the SSL pin of the RZ/1GE SoC to the 512 Mbits flash memory. When SW9 is set to the pin 3 side, the SSL pin of the RZ/G1E SoC to the 32 Mbits flash memory. | ||
+ | |||
+ | === SW10 (USB2.0 Channel 0 Host or Function Selection) === | ||
+ | {| | ||
+ | |- style="vertical-align:middle;" | ||
+ | | rowspan="2" | [[File:Switch.png|100px|Switch pin layout]] | ||
+ | | | ||
+ | {| class="wikitable" | ||
+ | |+ SW10 | ||
+ | |- | ||
+ | ! Function || style="background-color:#ccc;" | Pin 1 side (default) || Pin 3 side | ||
+ | |- | ||
+ | | USB0 mode | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> USB Host <br/> OVC </div> | ||
+ | | <div style="text-align: center;"> USB function <br/> VBUS </div> | ||
+ | |- | ||
+ | |} | ||
+ | |} | ||
+ | SW10 selects the mode of USB port 0 located on top of the USB connector. | ||
+ | {| class="wikitable" | ||
+ | |- | ||
+ | ! Position | ||
+ | ! Function | ||
+ | |- | ||
+ | | style="background-color:#ccc;" | Pin 1 side | ||
+ | | style="background-color:#ccc;" | | ||
+ | * USB0 is in host mode (default) | ||
+ | * USB0_OVC/VBUS pin goes low (0) if an overcurrent is detected on the USB power supply switch BD82065FVJ (U8). | ||
+ | |- | ||
+ | | Pin 3 side | ||
+ | | | ||
+ | * USB0 is in function mode. | ||
+ | * VBUS from USB connector (CN2) is connected to the USB0_OVC/VBUS pin of the RZ/G1E SoC. | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | === SW12 (User-Defined Software Switch) === | ||
+ | {| | ||
+ | |- style="vertical-align:middle;" | ||
+ | | [[File:DipSw4.png|85px|Switch pin layout]] | ||
+ | | | ||
+ | {| class="wikitable" | ||
+ | |+ SW12 | ||
+ | |- | ||
+ | ! No || Function || OFF ||ON | ||
+ | |- | ||
+ | | 1 | ||
+ | | bit 0, GP-3-9/AVB_RXD7 | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> 0 </div> | ||
+ | | <div style="text-align: center;"> 1 </div> | ||
+ | |- | ||
+ | | 2 | ||
+ | | bit 1, GP-3-10/AVB_RX_ER | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> 0 </div> | ||
+ | | <div style="text-align: center;"> 1 </div> | ||
+ | |- | ||
+ | | 3 | ||
+ | | bit 1, GP-3-11/AVB_COL | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> 0 </div> | ||
+ | | <div style="text-align: center;"> 1 </div> | ||
+ | |- | ||
+ | | 4 | ||
+ | | bit 1, GP-3-12/AVB_TX_EN | ||
+ | | style="background-color:#ccc;" | <div style="text-align: center;"> 0 </div> | ||
+ | | <div style="text-align: center;"> 1 </div> | ||
+ | |- | ||
+ | |} | ||
+ | |} | ||
+ | Before using SW12 as a general-purpose input switch, set up the GPSR3 register of the RZ/G1E SoC to select the GPIO function and set the PUPR3 register to enable pulling up. For details, refer to the section on the Pin Function Controller (PFC) in the RZ/G1E Hardware Manual. | ||
+ | |||
+ | == LEDs == | ||
+ | |||
+ | '''LD1''' (blue): indicates that 5V power has been applied to the board. | ||
+ | |||
+ | '''LD2''' (red): indicates that the board is turned on and has 3.3V power. | ||
+ | |||
+ | == Turning On and Off == | ||
+ | Special sequence is required for turning on and off the power supply to the RZ/G1E Starter Kit board: | ||
+ | *To turn ON: Press SW11 once | ||
+ | *To turn OFF: Long press SW11 | ||
+ | |||
+ | == Connectors == | ||
+ | === Video Out === | ||
+ | [[File:TouchscreenConnection.png|right|thumb|400px|Connecting a monitor with touchscreen to the Renesas RZ/G1E Starter Kit board]] | ||
+ | ==== HDMI (CN6) ==== | ||
+ | The digital RGB888 signal from the RZ/G1E SoC DU0 is connected to [http://www.analog.com/en/audiovideo-products/analoghdmidvi-interfaces/adv7511/products/product.html Analog Devices ADV7511] HDMI transmitter. The internal registers of ADV7511 are accessible via [http://en.wikipedia.org/wiki/I%C2%B2C I<sup>2</sup>C] interface (slave addresses: 0x72 for writring, 0x73 for reading). | ||
+ | |||
+ | The following displays have been tested with the RZ/G1E Starter Kit board: | ||
+ | * [http://www.gechic.com/product_help_en.asp?s=10 Gechic On-Lap1502I Touch Monitor] (Don't forget to set CONFIG_HID_MULTITOUCH and connect USB touchscreen) | ||
+ | * [http://lilliputweb.net/capacitive-touch-screen-monitors/fa1012-np-c-t.html Lilliput 10' with capacitive touch screen] (NOTE: picture quality is not good due to limited native resolution] | ||
+ | * [http://www.xenarc.com/700CSH.html Xenarc 7' capacitive touch] | ||
+ | |||
+ | ==== VGA (CN9) ==== | ||
+ | The digital RGB666 signal from the RZ/G1E SoC DU1 is connected to [http://www.analog.com/en/digital-to-analog-converters/da-converters/adv7123/products/product.html Analog Devices ADV7123] video D/A converter. This signal is then feed to the CN9 VGA connector. | ||
+ | |||
+ | The following displays have been tested with the RZ/G1E Starter Kit board: | ||
+ | * [http://www.gechic.com/product_help_en.asp?s=10 Gechic On-Lap1502I Touch Monitor] (Don't forget to set CONFIG_HID_MULTITOUCH and connect USB touchscreen) | ||
+ | |||
+ | <br clear=all> | ||
+ | ==== External LCD display (CN8) ==== | ||
+ | [[File:Connecting-LCD-KIT-B01.png|right|thumb|400px|Connecting LCD-KIT-B01 to the Renesas RZ/G1E Starter Kit board]] | ||
+ | The Renesas RZ/G1E Starter Kit board has a dedicated connector for [http://www.apnet.co.jp/product/xg/items/lcd_kit_b01.html LCD-KIT-B01] touchscreen panel. | ||
+ | |||
+ | [http://www.apnet.co.jp/support/man/lcd_kit_b01.pdf Datasheet] is available in Japanese. | ||
+ | |||
+ | [http://en.wikipedia.org/wiki/I%C2%B2C I<sup>2</sup>C] interface is available for getting touchscreen data.<br clear=all> | ||
+ | |||
+ | === Audio === | ||
+ | [[File:SSI_routing.png|right|thumb|400px|SSI routing on the Renesas RZ/G1E Starter Kit board]] | ||
+ | |||
+ | ==== Analog In/Out ==== | ||
+ | [http://www.akm.com/akm/en/product/datasheet1/?partno=AK4643EN AKM AK4643] audio codec is integrated on the Renesas RZ/G1E Starter Kit board. | ||
+ | |||
+ | AK4643 is in slave mode after reset and can be switched to master by writing to a special register via the [http://en.wikipedia.org/wiki/I%C2%B2C I<sup>2</sup>C] interface. It is assumed that SSI_DATA0 is set to transmit mode and SSI_SDATA1 is set to receive mode. | ||
+ | |||
+ | ==== HDMI (CN6) ==== | ||
+ | TBD ''Describe Audio Out through HDMI connector'' | ||
+ | <br clear=all> | ||
+ | |||
+ | === Debug Interface (CN1) === | ||
+ | [[File:arm-jtag-layout.gif|right|thumb|Pinout of ARM JTAG connector]] | ||
+ | The Renesas RZ/G1E Starter Kit board includes a 20-pin header for attaching a [http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0499b/BEHEIHCE.html ARM JTAG] debugger. TCK, TDI and TMS have internal 1.8V pull-up resistors. An additional resistor can be soldered to the board to add 1.8V pull-up to the ASEBRK pin. Refer to [[Board manual]] for more information.<br clear=all> | ||
+ | |||
+ | === MicroSD card slot === | ||
+ | The MicroSD card slot (CN4) is connected to the SD card host interface SDHI1 of the RZ/G1E SoC. When GP4_26 is set to 1, power is supplied. When GP4_26 is set to 0, power is shut off. | ||
+ | |||
+ | === eMMC === | ||
+ | 8GB eMMC [https://www.micron.com/parts/nand-flash/managed-nand/mtfc8glwdq-3m-ait-z MTFC8GLWDQ-3M AIT Z] (U5) is installed on the Renesas RZ/G1E Starter Kit board. It is connected to the SoC via 8-bit MMC interface. | ||
+ | |||
+ | eMMC is governed by [http://www.jedec.org/standards-documents/results/jesd84-b50 JESD84-B50 standard]. | ||
+ | |||
+ | === Ethernet === | ||
+ | The RZ/G1E Starter Kit board has one 10/100 Ethernet port compliant with IEEE 802.3u. [http://www.micrel.com/index.php/en/products/lan-solutions/phys/article/24-ksz8041rnl.html Micrel KSZ8041] (U13) PHY is used, in RMII mode. The port is Auto MDI/MDI-X | ||
+ | Since Ethernet AVB and EthetMAC use same pins of the SoC they cannot be used simultaneously. EtherMAC_B can be used with Ethernet AVB. | ||
+ | |||
+ | === Video In === | ||
+ | The Video Input interface on the RZ/G1E Starter Kit board can be used with misc. sources of standard analog baseband television signals compatible with NTSC, PAL. (For example: traditional analog CCTV or car front/rear cameras, media players) | ||
+ | |||
+ | The video signal from the Video In connector is converted with [http://www.analog.com/en/audiovideo-products/video-decoders/adv7180/products/product.html Analog Devices ADV7180] into 4:2:2 component 8-bit ITU-R BT.656 video data and passed to the RZ/G1E SoC VIN0 interface | ||
+ | |||
+ | === USB === | ||
+ | [[File:Silk USB.png|right|thumb|400px|USB connector on the Renesas RZ/G1E Starter Kit board]] | ||
+ | The CN2 USB type A connector has two ports. The upper port is Ch 0 and the lower port is Ch 1. USB 2.0 mode is supported to the corresponding USBx_OVC pin. | ||
+ | |||
+ | In host mode, each port is current-limited at 2.4 A by [http://www.rohm.com/web/eu/products/-/product/BD82065FVJ ROHM BD82065FVJ]. Overcurrent is reported to the Renesas RZ/G1E SoC. | ||
+ | |||
+ | ==== USB Host ==== | ||
+ | USB host mode is possible for both Ch 0 and Ch 1. For Ch0, SW10 should be switched to pin 1 side. | ||
+ | |||
+ | ==== USB Function ==== | ||
+ | USB function mode is possible for Ch0 when SW10 is set to pin 3 side. VBUS from CN2/lower is routed to USB0_OVC/VBUS pin of the Renesas RZ/G1E SoC. | ||
+ | |||
+ | Refer to [[RZ/G1E Starter Kit hardware manual]] for more information.<br clear=all> | ||
+ | |||
+ | === Debug Serial (CN13) === | ||
+ | The Renesas RZ/G1E SoC debug interface SCIF2 is exposed to the microUSB connector (CN13) via [http://www.silabs.com/support%20documents/technicaldocs/cp2102-9.pdf Silicon Labs CP2102]. Refer to [[RZ-G/Boards/SK-RZG1E#Booting_over_TFTP_from_U-Boot]] for configuring and using the interface. | ||
+ | |||
+ | CP2102 is self powered and requires no power over USB. Keep in mind that CP2102 will not be detected by the host PC until the Renesas RZ/G1E Starter Kit board is connected to 5 V power source. | ||
+ | |||
+ | === EXIO (JP1, JP2) === | ||
+ | [[File:SILK EXIO.png|right|thumb|upright|Pin locations on EXIO connectors (JP1, JP2) of the Renesas RZ/G1E Starter Kit board]] | ||
+ | The Renesas RZ/G1E Starter Kit board includes two EXIO connectors. Both are "Box Wafer, 2.0-mm pitch". | ||
+ | |||
+ | JP1 has [http://en.wikipedia.org/wiki/I%C2%B2C I<sup>2</sup>C] interface, connected to SDA3/SCL3 of the Renesas RZ/G1E SoC. | ||
+ | |||
+ | {|class="wikitable" | ||
+ | |+ List of EXIO Connector (JP1) Pins | ||
+ | |- | ||
+ | ! Pin || Signal || Pin || Signal | ||
+ | |- | ||
+ | | 1 || MSIOF1_SYNC || 2 || MSIOF1_SCK | ||
+ | |- | ||
+ | | 3 || MD5/MSIOF1_TXD || 4 || MISOF1_RXD | ||
+ | |- | ||
+ | | 5 || I2C3_SDA_B || 6 || I2C3_SCL_B | ||
+ | |- | ||
+ | | 7 || GP3_22 || 8 || GP3_30 | ||
+ | |- | ||
+ | | 9 || GND || 10 || GND | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | {|class="wikitable" | ||
+ | |+ List of EXIO Connector (JP2) Pins | ||
+ | |- | ||
+ | ! Pin || Signal || Pin || Signal | ||
+ | |- | ||
+ | |1 || D3.3V || 2 || GP1_14/TS_SDATA0_B | ||
+ | |- | ||
+ | |3 || GP1_16/TS_SDEN0_B || 4 || GP1_17/TS_SPSYNC0_B | ||
+ | |- | ||
+ | |5 || GP1_15/TS_SCK0_B || 6 || GND | ||
+ | |- | ||
+ | |}<br clear=all> | ||
+ | |||
+ | |||
+ | === U17 - Placeholder === | ||
+ | |||
+ | U17 can be used to connect Apple Authentication IC (I2C4 on the RZ/G1E) | ||
+ | |||
+ | == Integrated WiFi/Bluetooth Module == | ||
+ | |||
+ | Information regarding the on-board WiFi/BT module will be made available later (January 2015) | ||
+ | |||
+ | == Connecting external USB devices == | ||
+ | === USB Bluetooth === | ||
+ | TBD | ||
+ | |||
+ | === USB 3G Modem === | ||
+ | TBD | ||
+ | |||
+ | === USB Video Camera === | ||
+ | TBD | ||
+ | |||
+ | === USB HID === | ||
+ | TBD | ||
+ | |||
+ | === USB Ethernet === | ||
+ | TBD | ||
+ | |||
+ | === USB GPS === | ||
+ | TBD | ||
+ | |||
+ | === USB CAN === | ||
+ | TBD | ||
+ | |||
+ | === USB Radio === | ||
TBD | TBD |
Revision as of 18:19, 29 October 2015
Contents
|
This page contains information on the RZ-G/Boards/SK-RZG1E hardware.
Board Layout
Power Plug
The RZ/G1E Starter Kit board uses a 5.5 x 2.1mm barrel 5V power plug. It is a Center Positive power supply, indicating that the center (tip) of the output plug is positive (+) and the outer barrel is negative (-).
- North American Power Supply from Digikey - 5V@2.5A -CUI EPSA050250U-P5P-EJ
- European Power Supply from Digikey - 5V@2.5A - CUI EPSA050250UE-P5P-EJ
- Power Supply from Sparkfun - 5V@2A - TOL-12889
- Power Supply from Adafruit - 5V@2A - PRODUCT-ID:276
- Power Supply from SeeedStudio - 5V@2A SKU: POW06182B
Switches and Buttons
SW1 (SSI_DATA1 Routing)
Switch pin layout |
|
SW1 selects the device to be connected to the SSI_DATA1/ETH_RXD0_B (GP-5-13) pin of the the RZ/G1E SoC. The pin is normally set to receive mode.
Position | Function |
---|---|
Pin 1 side |
|
Pin 3 side |
|
SW2 (TRST# Pull-up)
Switch pin layout |
|
SW2 selects whether to pull up or down the TRST# pin of the RZ/G1E SoC JTAG interface.
SW3, SW4, SW6 (Push Buttons)
Pushbutton |
|
The active signal (low or high) for SW3-SW5 is selected by the corresponding bit of POSNEG register. Refer to to the section GPIO in the RZ/G1E Hardware Manual for details.
SW7 (Mode Setting A)
Switch pin layout |
|
MD21 determines the JTAG mode. Select OFF position to use JTAG debugger.
MD19 determines the SDRAM clock speed. It must remain in OFF position to select DDR3-1333.
SW9 (SPI Flash Memory Selection)
Switch pin layout |
|
The RZ/G1E Starter Kit board is equipped with 512 Mbits SPI flash memory (U6: S25FL512SAGMFIG11) and 32 Mbits SPI flash memory (U7: S25FL032P0XMFI011). When SW9 is set to the pin 1 side, the SSL pin of the RZ/1GE SoC to the 512 Mbits flash memory. When SW9 is set to the pin 3 side, the SSL pin of the RZ/G1E SoC to the 32 Mbits flash memory.
SW10 (USB2.0 Channel 0 Host or Function Selection)
Switch pin layout |
|
SW10 selects the mode of USB port 0 located on top of the USB connector.
Position | Function |
---|---|
Pin 1 side |
|
Pin 3 side |
|
SW12 (User-Defined Software Switch)
Switch pin layout |
|
Before using SW12 as a general-purpose input switch, set up the GPSR3 register of the RZ/G1E SoC to select the GPIO function and set the PUPR3 register to enable pulling up. For details, refer to the section on the Pin Function Controller (PFC) in the RZ/G1E Hardware Manual.
LEDs
LD1 (blue): indicates that 5V power has been applied to the board.
LD2 (red): indicates that the board is turned on and has 3.3V power.
Turning On and Off
Special sequence is required for turning on and off the power supply to the RZ/G1E Starter Kit board:
- To turn ON: Press SW11 once
- To turn OFF: Long press SW11
Connectors
Video Out
HDMI (CN6)
The digital RGB888 signal from the RZ/G1E SoC DU0 is connected to Analog Devices ADV7511 HDMI transmitter. The internal registers of ADV7511 are accessible via I2C interface (slave addresses: 0x72 for writring, 0x73 for reading).
The following displays have been tested with the RZ/G1E Starter Kit board:
- Gechic On-Lap1502I Touch Monitor (Don't forget to set CONFIG_HID_MULTITOUCH and connect USB touchscreen)
- Lilliput 10' with capacitive touch screen (NOTE: picture quality is not good due to limited native resolution]
- Xenarc 7' capacitive touch
VGA (CN9)
The digital RGB666 signal from the RZ/G1E SoC DU1 is connected to Analog Devices ADV7123 video D/A converter. This signal is then feed to the CN9 VGA connector.
The following displays have been tested with the RZ/G1E Starter Kit board:
- Gechic On-Lap1502I Touch Monitor (Don't forget to set CONFIG_HID_MULTITOUCH and connect USB touchscreen)
External LCD display (CN8)
The Renesas RZ/G1E Starter Kit board has a dedicated connector for LCD-KIT-B01 touchscreen panel.
Datasheet is available in Japanese.
I2C interface is available for getting touchscreen data.
Audio
Analog In/Out
AKM AK4643 audio codec is integrated on the Renesas RZ/G1E Starter Kit board.
AK4643 is in slave mode after reset and can be switched to master by writing to a special register via the I2C interface. It is assumed that SSI_DATA0 is set to transmit mode and SSI_SDATA1 is set to receive mode.
HDMI (CN6)
TBD Describe Audio Out through HDMI connector
Debug Interface (CN1)
The Renesas RZ/G1E Starter Kit board includes a 20-pin header for attaching a ARM JTAG debugger. TCK, TDI and TMS have internal 1.8V pull-up resistors. An additional resistor can be soldered to the board to add 1.8V pull-up to the ASEBRK pin. Refer to Board manual for more information.
MicroSD card slot
The MicroSD card slot (CN4) is connected to the SD card host interface SDHI1 of the RZ/G1E SoC. When GP4_26 is set to 1, power is supplied. When GP4_26 is set to 0, power is shut off.
eMMC
8GB eMMC MTFC8GLWDQ-3M AIT Z (U5) is installed on the Renesas RZ/G1E Starter Kit board. It is connected to the SoC via 8-bit MMC interface.
eMMC is governed by JESD84-B50 standard.
Ethernet
The RZ/G1E Starter Kit board has one 10/100 Ethernet port compliant with IEEE 802.3u. Micrel KSZ8041 (U13) PHY is used, in RMII mode. The port is Auto MDI/MDI-X Since Ethernet AVB and EthetMAC use same pins of the SoC they cannot be used simultaneously. EtherMAC_B can be used with Ethernet AVB.
Video In
The Video Input interface on the RZ/G1E Starter Kit board can be used with misc. sources of standard analog baseband television signals compatible with NTSC, PAL. (For example: traditional analog CCTV or car front/rear cameras, media players)
The video signal from the Video In connector is converted with Analog Devices ADV7180 into 4:2:2 component 8-bit ITU-R BT.656 video data and passed to the RZ/G1E SoC VIN0 interface
USB
The CN2 USB type A connector has two ports. The upper port is Ch 0 and the lower port is Ch 1. USB 2.0 mode is supported to the corresponding USBx_OVC pin.
In host mode, each port is current-limited at 2.4 A by ROHM BD82065FVJ. Overcurrent is reported to the Renesas RZ/G1E SoC.
USB Host
USB host mode is possible for both Ch 0 and Ch 1. For Ch0, SW10 should be switched to pin 1 side.
USB Function
USB function mode is possible for Ch0 when SW10 is set to pin 3 side. VBUS from CN2/lower is routed to USB0_OVC/VBUS pin of the Renesas RZ/G1E SoC.
Refer to RZ/G1E Starter Kit hardware manual for more information.
Debug Serial (CN13)
The Renesas RZ/G1E SoC debug interface SCIF2 is exposed to the microUSB connector (CN13) via Silicon Labs CP2102. Refer to RZ-G/Boards/SK-RZG1E#Booting_over_TFTP_from_U-Boot for configuring and using the interface.
CP2102 is self powered and requires no power over USB. Keep in mind that CP2102 will not be detected by the host PC until the Renesas RZ/G1E Starter Kit board is connected to 5 V power source.
EXIO (JP1, JP2)
The Renesas RZ/G1E Starter Kit board includes two EXIO connectors. Both are "Box Wafer, 2.0-mm pitch".
JP1 has I2C interface, connected to SDA3/SCL3 of the Renesas RZ/G1E SoC.
Pin | Signal | Pin | Signal |
---|---|---|---|
1 | MSIOF1_SYNC | 2 | MSIOF1_SCK |
3 | MD5/MSIOF1_TXD | 4 | MISOF1_RXD |
5 | I2C3_SDA_B | 6 | I2C3_SCL_B |
7 | GP3_22 | 8 | GP3_30 |
9 | GND | 10 | GND |
Pin | Signal | Pin | Signal |
---|---|---|---|
1 | D3.3V | 2 | GP1_14/TS_SDATA0_B |
3 | GP1_16/TS_SDEN0_B | 4 | GP1_17/TS_SPSYNC0_B |
5 | GP1_15/TS_SCK0_B | 6 | GND |
U17 - Placeholder
U17 can be used to connect Apple Authentication IC (I2C4 on the RZ/G1E)
Integrated WiFi/Bluetooth Module
Information regarding the on-board WiFi/BT module will be made available later (January 2015)
Connecting external USB devices
USB Bluetooth
TBD
USB 3G Modem
TBD
USB Video Camera
TBD
USB HID
TBD
USB Ethernet
TBD
USB GPS
TBD
USB CAN
TBD
USB Radio
TBD