Search results

Jump to: navigation, search
  • ...ve the switch contacts available as pins. For these, put the wires into a jumper than can be placed on the pins.
    4 KB (677 words) - 12:30, 24 September 2007
  • Make sure the jumper by the USB port is in the right location for HOST mode (check manual).
    630 bytes (101 words) - 21:55, 12 April 2011
  • * Jumper selectable reset address. Reset vector can be located at 0xFFFE,0xFFFF or 0 ...II now has the option to set the reset vector to location $FFFE:FFFF with jumper JP18 (MODB).
    19 KB (3,082 words) - 03:38, 28 April 2012
  • ** Headers can be jumper configured
    2 KB (358 words) - 13:35, 9 June 2010
  • '''Please NOTE:''' You must jumper select each four pin section on Hammer-RDP for either 3.3V or 5V operation,
    8 KB (1,194 words) - 13:24, 17 November 2008
  • ...ot, try jumpering DTR (pin 4) to DSR (pin 6) and repeat test. You can also jumper RTS (pin7) to CTS (pin 8) if you don't trust your software to have turned o
    45 KB (7,428 words) - 22:05, 29 May 2020
  • ...If you do not have one or want to purchase one, you can simply install a jumper at JP6. Additionally, the Digital View documentation explains how to contr
    5 KB (800 words) - 18:22, 31 December 2013
  • LC475: If the jumper J18 is not, it is a LC475. The system and other software know this from wha It makes no difference if the jumper is installed or not.
    163 KB (25,069 words) - 15:01, 27 October 2011
  • * Hardware Skills: General breadboarding with jumper wires.<br /> * Hardware Skills: Ability to jumper wire BBB to an off the shelf TTL LCD panel breakout.<br />
    28 KB (4,193 words) - 19:14, 13 November 2016
  • 2. Mount Jumper J1 on Innostick 6(Supply from Micro-USB cable)<br/> 3. Leave Jumper J2 open on Innostick 6(Normal Boot Mode)<br/>
    8 KB (1,060 words) - 19:56, 25 August 2018
  • ...ignals are level translated to either +3.3V or +5V (user selectable with a jumper). The I²C signals are located next the the prototyping area. ...wo traces on the back of the board connecting the two header holes so that jumper are not required.
    15 KB (2,267 words) - 18:53, 1 January 2014
  • ...ou should be ready to boot using your new bootloader. Remove the UART-boot jumper and type <code>reset</code> in u-boot and see what happens.
    7 KB (1,095 words) - 17:03, 15 April 2011
  • ...ansion board ID standard]]. While normally write-protected, a Write-Enable jumper is provided to set the ID and any other data stored in the EEPROM. This dev ...ion to the FPGA, along with two power and two ground connections. Power is jumper selectable as either 3.3V or 5V on a per-connector basis. Digilent (and oth
    12 KB (1,881 words) - 21:20, 1 January 2014
  • [1] As an alternative to TP103, either side of R43 (jumper/0 Ohms) or the right pad of R45 (unpopulated) works. This is near the other
    7 KB (1,033 words) - 03:11, 27 October 2011
  • 2x Switches or jumper pins ...esistor in series. So that when the connection is closed via the switch or jumper, it completes the circuit. This is pulling the SD[13] high and SD[6] low, w
    6 KB (963 words) - 02:58, 27 October 2011
  • This is a list of the jumper settings for gpiob[2:5] on an [[LeapFrog_Pollux_Platform| LeapFrog Pollux P
    1,016 bytes (129 words) - 23:16, 22 July 2011
  • ...agleboard header pin 23, I2C2_SDA and pin 24, I2C2_SCL with a 3.3V or 5v (jumper selectable) voltage translator. This is i2c bus 2 in user space or i2c bus ...ft to right, [gnd, 3.3V, SDA, SCL]. Notice also how the I2C voltage select jumper (JP1) is on the 3.3V or 3v3 position.
    9 KB (1,531 words) - 22:45, 12 April 2011
  • * [https://www.sparkfun.com/products/11026 Jumper Wires]
    1 KB (158 words) - 12:40, 8 July 2013
  • [1] As an alternative to TP103, either side of R43 (jumper/0 Ohms) or the right pad of R45 (unpopulated) works. This is near the other
    1 KB (186 words) - 10:18, 12 July 2011
  • ==== Pi Jumper & Pi Jumper Plus (GPIO breakout, 3v3 power, 3v3 & 5V I2C) ==== [http://www.mikronauts.com/raspberry-pi/pi-jumper/ Pi Jumper is the ultimate Raspberry Pi breakout board from [http://Mikronauts.com Mik
    121 KB (18,882 words) - 05:25, 30 December 2019

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)